Deze gebruiker heeft hun profiel nog niet ingevuld.
Mijn wiki's
Vragen
I have a 4Patriots D320 powerbank that was sitting unused and not charged for a couple of years. It would not charge, so I...
Meer informatieWestinghouse WD24HB6101. 24" with DVD player. I plug it in, LED lights red. I press on/off button or use remote. LED...
Meer informatieI have a Whirlpool WRF736SDAM14 refer. When it runs it makes a noise at 1.2kHz per my phone app. Sometimes I see a 2nd...
Meer informatieI just had to fix a flea power problem. The solution said to remove the battery. fortunately, that wasn't necessary...
Meer informatieMy phone was working fine until a week or so ago. Now I can't receive calls. I can make calls, I can make and rcv text....
Meer informatieI put a voltmeter on a 2017 Highlander that I just bought. The readings don’t make any sense. When it is idling in park,...
Meer informatieMy sister has a Logitech Type+ keyboard for an Ipad. It does not have replaceable batteries, they are rechargeable. The...
Meer informatieAntwoorden
Search on AliExpress for one for your device.
Meer informatieI had a white to green line on my Samsung. Bad display. Replaced, line gone.
Meer informatieWhat I found with a simple search: You can to A loud noise during the spin cycle of a Kenmore 110 Series washing machine could be caused by several issues, including a worn-out transmission, clutch assembly, tub bearing, or drain pump. Other potential causes include foreign objects in the tub, a misaligned or unbalanced load, or a problem with the drive belt or moto
Meer informatieSparking brushes are common with a new set of brushes. Hopefully, you cleaned the commutator and polished it up a bit. That should reduce the a time it takes for the brushes to seat and the sparks to minimize.
Meer informatieIt might help to post the old and new p/n, and also what "power IC" you are talking about. Maybe even what page of the manual it is on. I just downloaded the manual and it is huge. A thermal camera would be a useful tool here to see what is overheating. A blown device might indicate it had some external help blowing out, or not. That cause may still be present, or it may be the part substitution doesn't work.
Meer informatieYour observation is good. Expanding capacitors would be a very likely cause. It is an all to common problem. The voltage to your backlights is going on/off and those caps will cause if they are in that circuit. They can also cause it if they are in another circuit.
Meer informatieSince you replaced the battery prior to this issue, I would start by reviewing your work. It is possible you did not get the battery connector or other connector properly seated. If it really isn't charging, then it is more likely the battery connector or a connector from the USB port if it is not integral with a PCB. If it is charging, then maybe another connector.
Meer informatieFirst, you must find the wires from the thermo to the pcb. Shorting out the thermo, might cause the PCB to shut down (if it were smart). But what does it do that leads you to believe it might be the thermo? How long between days of operation? What happens during its down time? Does it make any strange noises? Does anything work during its downtime?
Meer informatieSounds like the fix may be more than it is worth. If you are handy, you could probably do the screen replacement, but you need to figure out the port problem first. If that involves replacing an internal component, it might be $ or $$$. Water can cause corrosion on a PCB or just on your charging connector. So, there is no telling what that issue is.
Meer informatieBeing a Ninja, my experience with a couple of Bullets might indicate a factory defect of an open power connection. I also had a broken switch activator. Being totally dead I would start at the plug, not the PCB. It might be a bad connection in the plug itself.
Meer informatiePagina 1 van 129
Commentaar Gids
there is double face tape at each end of the chromed plastic piece along with the tabs that need to be unhooked when prying off. So be tender and do not use brute force. Also, the clear plastic piece will likely just fall out so be aware.
You must use a very small blade Phillips screwdriver. A #0 will be too big. Significant downward pressure is also needed to break the screw loose and prevent stripping the screw. It feels like they are glued in. The battery is available in many places and is a 14500 type rated at 750mAh with a 4mm tab on the positive side and a 2.5mm tab on the negative side.
bill
@ruggb
5.567
Reputatie
1.290
Oplossingen
0
Handleidingen
Lid sinds 05/09/21
Stemmen
4
94