@jcfal  ''

Off-and-On Use

Switches-

Wearing power switches will cause off-and-on use as their connections wear down, sometimes requiring several pulls of the trigger before the tool starts up.

Brushes-

Wearing or damaged brushes can cause a similar off-and-on use problem, but this is usually because wear, damage, or a "burr" formation is preventing the carbon brush from correctly contacting the armature's commutator.

If your brushes are pushed firmly against the motor armature and have no burrs and the contact wires are okay it is unlikely that the brushes that have failed.

Check on here for more

@jcfal what you see in step 12 of this guide DeWalt DWD112 Brush Replacement are the brushes. The carbon and the metal around it are the brush assembly. You can however purchase the brushes separately. Dewalt part number for the brushes assembly with the yellow wire is 64714203 for the red wire 64714202 and the brushes itself (you would need 2 of course) is 64938000. I’d go with the complete assembly since it is an easier repair but that is totally up to you.

The above answer is assuming the batteries are actually good, which is the first potential cause. They may appear charged but have such high internal resistance that you can’t get enough current out of them. Try testing them with a resistance load and a multimeter.

Mohammed Basith Awan use something like this video or even this one for the how to. Once you are going to replace your screen, it would be great if you create a guide so that teh next person looking for an answer, can find it on iFixit. It’s not complicated to create a guide. https://www.ifixit.com/Guide/new

Now if you are thinking about a glass only repair, that would be very complicated since glass and screen are fused. You would need some special tools to separate the display and subsequently to re-adhere etc. The cost for the tools and your chances of getting it right the first are slim and expensive. Replacing the complete display will have greater success.

Hi @ruggs

It depends.

If you can read schematic circuits and have and know how to use a DMM (digital multimeter) then here’s the service manual for the receiver. It has the full wiring diagram for the receiver, some troubleshooting flowcharts, disassembly instructions and a parts list, so basically it has everything you need to locate and fix the problem.

It may be something simple like a faulty connection to the left speaker output connector or as difficult as tracking down the problem from the left speaker output terminal back through the left speaker channel audio amp stages etc. until you locate where the problem lies. You won’t know until you start testing.

If you don’t know how to read wiring diagrams or how to safely test “live” circuits with a DMM, then it will be extremely difficult.

Hi,

You will have to open the phone and check what damage has occurred and then after it has been properly cleaned check to see what happens when you turn it on to know what works and what doesn’t.

Water and electronics and electricity are not a good mix.

The impurities in the water causes corrosion and provides circuit paths for the electricity which are not in the phone’s operating design and could damage the components. The corrosion process starts immediately and is ongoing until it has been properly cleaned away.

Rice does not fix the problems caused by corrosion Rice is for dinner, not repair

Bit late now but do not try to charge or to turn on your phone and then remove the battery as soon as possible to prevent any further damage.

Then you need to dis-assemble the rest of the phone and clean all the affected parts using Isopropyl Alcohol 99%+ (available from electronics parts stores) to remove all traces of corrosion. Do not use "rubbing alcohol" as in some cases this is <70% IPA, can contain additives and is not as effective. If you do have to use it, check the label to verify the amount of IPA. The higher the percentage of IPA, the better.

Here is a link that describes the process. Electronics Water Damage

As always with electronics, especially surface mounted pcb be gentle when handling and especially when brushing away the corrosion. You do not want to remove any components from the boards. You will have to remove the metal shields that are covering any of the components as the water may have got in under them and there is ongoing corrosion there as well. Also disconnect and clean any flex cable ends and their associated connectors on the systemboard.

Hopefully after you have done all this the phone might possibly work correctly again.

Here is a teardown video of the phone which may be of some help.

If this process seems too daunting, take your phone to a reputable, professional mobile repair service, experienced in water damage repair and ask for a quote for a repair. If you decide to do this, do it sooner than later.

Zaryad oladigan joyi katalashgan

You won't be able to find individual parts for the window regulator. The fix is to just buy a complete window regulator and install it. It's not really a complicated repair. You have to remove the interior door panel and secure the glass in the up position. Then disconnect the sash clips that hold the glass to the regulator and remove the regulator. This article shows a step-by-step on how to replace a regulator

You won't be able to find individual parts for the window regulator. The fix is to just buy a complete window regulator and install it. It's not really a complicated repair. You have to remove the interior door panel and secure the glass in the up position. Then disconnect the sash clips that hold the glass to the regulator and remove the regulator. This article shows a step-by-step on how to replace a regulator

@oldturkey03 PLEASE HELP, URGENT HELP, PLEASE CONNECT ME ON DISCORD. Bro I am dead, help me out💀💀💀💀💀💀