Ga door naar hoofdinhoud

三星 盖乐世 S8 Plus背板更换指南

Waarschuwing: Je bewerkt een vooraf vereiste handleiding. Alle wijzigingen die je hierin maakt, beïnvloeden alle 5 handleidingen die deze stap bevatten.

Stap 11 vertalen

Stap 11
Samsung Galaxy S8+ Back Glass Replacement: stap 0, afbeelding 1 van 1
  • Remove the back cover.

  • To install a new back cover:

  • Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.

  • Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.

  • To reinstall the back cover, or to install a back cover without pre-installed adhesive, follow this guide.

  • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

  • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

  • You may also need to transfer the camera bezel to your new part. If that's the case, follow our camera bezel replacement guide.

您已经成功移除了背板。

重新组装背板:

首先使用镊子移除背板和手机背面所有的残胶。

接着,使用至少90%异丙醇和不起毛布清洁粘胶的位置。请朝一个擦拭,不要往回或者转圈。这回帮助你准备好重新上胶的表面。

使用与背板匹配的预切胶条。如果买不到的话,请使用高粘性的双面胶,比如Tesa 61395. 注意使用双面胶将会留下缝隙,并且影响防水性能。

在装回背板后,施加一个稳定的强大的压力几分钟来帮助胶粘牢。比如说把你的手机压在几本厚重的百科全书下面。

如果你很着急,你可以不更换胶条而冲洗装上背板。移除会使背板无法平整装回的大块胶条。在装上去之后,加热背板并且施加一定的压力来固定她。尽管这样的胶条不再防水,但是固定住背板还是足够了。

[* black] Remove the back cover.
-[* icon_reminder] To reinstall the back cover:
- [* black] First use tweezers to peel away any remaining adhesive from both the back cover and the phone's chassis.
- [* black] Then, clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.
- [* black] Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
- [* icon_note] Replacement adhesive comes in a pre-cut sheet to match the exact contours of the back cover. If that's not available, you can use a high-bond double-sided tape, such as [product|IF317-072-1|Tesa 61395|new_window=true]. Be aware that this leaves gaps that are vulnerable to liquid intrusion.
- [* black] After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.
+[* icon_reminder] To install a new back cover:
+ [* black] Use [product|IF145-020|tweezers] to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.
+ [* black] Peel the adhesive backing off of the new rear glass, carefully line up one edge of the glass against the phone chassis, and firmly press the glass onto the phone.
+[* icon_reminder] To reinstall the back cover, or to install a back cover without pre-installed adhesive, [guide|124003|follow this guide|new_window=true].
+ [* icon_note] Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.
+[* icon_reminder] You may also need to transfer the camera bezel to your new part. If that's the case, follow our [guide|123030|camera bezel replacement guide|stepid=237617|new_window=true].

Je bijdragen zijn gelicentieerd onder de open source Creative Commons-licentie.