Ga door naar hoofdinhoud

Inleiding

Follow this guide to remove and replace a shattered rear glass panel, or to change the color of the panel, for the Google Pixel XL.

  1. Heat an iOpener and apply it to the phone's back glass panel for two minutes.
    • Heat an iOpener and apply it to the phone's back glass panel for two minutes.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

  2. When the glass is warm to the touch, apply a suction cup close to the edge. Lift on the suction cup and insert an opening pick in the gap. If your back glass is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. You can also superglue the suction cup to the broken screen.
    • When the glass is warm to the touch, apply a suction cup close to the edge.

    • Lift on the suction cup and insert an opening pick in the gap.

    • If your back glass is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. You can also superglue the suction cup to the broken screen.

    • If the edge of the glass is cracked, you can try to slide an opening pick underneath the crack and slowly chip the glass out.

    • Reapplying heat will help loosen adhesive and make the process easier.

  3. Use the opening pick to slice through the glass panel's perimeter adhesive. If the slicing becomes hard, reapply heat to the panel. If the slicing becomes hard, reapply heat to the panel.
    • Use the opening pick to slice through the glass panel's perimeter adhesive.

    • If the slicing becomes hard, reapply heat to the panel.

  4. When you free the back glass around the fingerprint sensor, press down on the sensor firmly until it separates from the back glass. Continue to slice through the adhesive underneath the back glass until you are able to remove the panel.
    • When you free the back glass around the fingerprint sensor, press down on the sensor firmly until it separates from the back glass.

    • Continue to slice through the adhesive underneath the back glass until you are able to remove the panel.

    • Cracked glass can be extremely sharp! Be careful while prying and clean up all glass fragments.

  5. Use a spudger or opening tool to scrape all adhesive from the frame.
    • Use a spudger or opening tool to scrape all adhesive from the frame.

    • Use high concentration isopropyl alcohol (over 90%) to wipe away any remaining residue.

    • Be meticulous with the cleaning. If any adhesive is left on the frame, the replacement panel may not lay flat and adhere properly.

  6. Peel the white backing away from the included adhesive sheet, making sure to punch out all cutouts. Line the bottom edge of the adhesive to the bottom edge of the replacement glass panel. Make sure that the backside of the glass panel is facing upwards.
    • Peel the white backing away from the included adhesive sheet, making sure to punch out all cutouts.

    • Line the bottom edge of the adhesive to the bottom edge of the replacement glass panel.

    • Make sure that the backside of the glass panel is facing upwards.

    • Slowly lower the adhesive onto the glass panel.

    • Rub your fingers against the adhesive to help it bond with the glass panel.

  7. If your replacement part did not come with a flash lens, you must transfer it from your old panel. Use a spudger or your finger to firmly press on the lens from the outward-facing side (the side you can usually see on the phone) of the glass panel until it loosens from its recess. Remove the lens and transfer it onto the back side of the replacement panel.
    • If your replacement part did not come with a flash lens, you must transfer it from your old panel.

    • Use a spudger or your finger to firmly press on the lens from the outward-facing side (the side you can usually see on the phone) of the glass panel until it loosens from its recess.

    • Remove the lens and transfer it onto the back side of the replacement panel.

    • Make sure to orient the flash lens properly such that the fresnel rings are stacked vertically.

  8. Peel the liner off of the adhesive-backed glass panel. Align the glass panel to the bottom edge of the indentation. Lower the glass panel into place.
    • Peel the liner off of the adhesive-backed glass panel.

    • Align the glass panel to the bottom edge of the indentation.

    • Lower the glass panel into place.

  9. To help the back glass adhesive bond more securely, stack some heavy books on top of the phone for 30 minutes.
    • To help the back glass adhesive bond more securely, stack some heavy books on top of the phone for 30 minutes.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Check out our Google Pixel XL Answers community for troubleshooting help.

8 andere personen hebben deze handleiding voltooid.

Arthur Shi

Lid sinds: 03-01-18

79.949 Reputatie

262 handleidingen geschreven

Team

iFixit Lid van iFixit

Community

107 Leden

9.557 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 11

Afgelopen 7 dagen: 55

Afgelopen 30 dagen: 303

Altijd: 3,195