Ga door naar hoofdinhoud

Repareer je spullen

Recht op reparatie

Winkel

Help

Deze versie is geschreven door: m0t3x ,

Tekst:

Steps you should take before advanced soldering techniques.
 
1. Hold Power and Home Button for Hard Reset
 
2. Unplug battery cable, reconnect, power on
 
3. Check your LCD connector for damage, dirt, metal, lint, etc
 
a. Check LCD connector on the motherboard for same
 
4. Curse yourself for not unplugging the battery while working on it
 
5. Multi meter the green traces that YoloRepair pointed out
 
6. Perform a fuse replacement, or a jump. - Recommended you seek pro help, because this type of repair requires a stereoscope and a extremely steady hand with soldering skills.
 
-----------------------------------------------
 
Making Jumper Steps
 
1. Make sure it's that part - http://i39.tinypic.com/3130ry8.jpg
 
2. Give yourself access to both side, I made small cut on shield
 
3. Remove blown fuse, replace or jump. I chose jump - http://i44.tinypic.com/2lbno5k.jpg
 
4. Test - WOOHOO! Thanks YoloRepair <3 - http://i39.tinypic.com/2924cyb.jpg
 
5. Clean excess flux and leave repair area in best shape possible - http://i40.tinypic.com/mbtok3.jpg
 
6. Test everything again, close it, and get sigh of relief.
 
7. Thank YoloRepair once more.
 
I accept mail in - m0t3x@yahoo.com

Status:

open

Bewerkt door: m0t3x ,

Tekst:

Steps you should take before advanced soldering techniques.
 
1. Hold Power and Home Button for Hard Reset
 
2. Unplug battery cable, reconnect, power on
 
3. Check your LCD connector for damage, dirt, metal, lint, etc
 
a. Check LCD connector on the motherboard for same
 
4. Curse yourself for not unplugging the battery while working on it
 
5. Multi meter the green traces that YoloRepair pointed out
 
6. Perform a fuse replacement, or a jump. - Recommended you seek pro help, because this type of repair requires a stereoscope and a extremely steady hand with soldering skills.
 
-----------------------------------------------
 
Making Jumper Steps
 
1. Make sure it's that part - http://i39.tinypic.com/3130ry8.jpg
 
2. Give yourself access to both side, I made small cut on shield
 
3. Remove blown fuse, replace or jump. I chose jump - http://i44.tinypic.com/2lbno5k.jpg
 
4. Test - WOOHOO! Thanks YoloRepair <3 - http://i39.tinypic.com/2924cyb.jpg
 
5. Clean excess flux and leave repair area in best shape possible - http://i40.tinypic.com/mbtok3.jpg
 
6. Test everything again, close it, and get sigh of relief.
 
7. Thank YoloRepair once more.
 
I accept mail in - m0t3x@yahoo.com

Status:

open

Origineel bericht door: m0t3x ,

Tekst:

Steps you should take before advanced soldering techniques.

1. Hold Power and Home Button for Hard Reset

2. Unplug battery cable, reconnect, power on

3. Check your LCD connector for damage, dirt, metal, lint, etc

a. Check LCD connector on the motherboard for same

4. Curse yourself for not unplugging the battery while working on it

5. Multi meter the green traces that YoloRepair pointed out

6. Perform a fuse replacement, or a jump. - Recommended you seek pro help, because this type of repair requires a stereoscope and a extremely steady hand with soldering skills.

-----------------------------------------------

Making Jumper Steps

1. Make sure it's that part - http://i39.tinypic.com/3130ry8.jpg

2. Give yourself access to both side, I made small cut on shield

3. Remove blown fuse, replace or jump. I chose jump - http://i44.tinypic.com/2lbno5k.jpg

4. Test - WOOHOO! Thanks YoloRepair <3 - http://i39.tinypic.com/2924cyb.jpg

5. Clean excess flux and leave repair area in best shape possible - http://i40.tinypic.com/mbtok3.jpg

6. Test everything again, close it, and get sigh of relief.

7. Thank YoloRepair once more.

Status:

open