Ga door naar hoofdinhoud
Help

Deze versie is geschreven door: julian clark

Tekst:

-(Kenmore HE3)…same thing... mine would not lock, error 'DL'... i replaced the door latch mechanism, which did '''not''' solve the problem. -i removed the three torx screws from the top-back of the unit, lifted the back cover up '''gently''' an inch, and slid the top of the washer away from me, removed top. -then i just reseated the pink wire connector (i reseated them all). -problem solved, for now. -must be a poor connection (vibration?). -cost me $73 for the latch i didn't need, hope i save you $.
-update 1/20/18:
--eventually i had to re-solder the board where the connectors make contact, which involved removing the board and adding a bit of solder to each of the contact points on the board, been years now without a fault.
+*****eventually i had to re-solder the board where the connectors make contact, which involved removing the board and adding a bit of solder to each of the contact points on the board, been years now without a fault. This was the solution.

Status:

open

Bewerkt door: julian clark

Tekst:

--same thing... mine would not lock, error 'DL'... i replaced the door latch mechanism, which did '''not''' solve the problem. -i removed the three torx screws from the top-back of the unit, lifted the back cover up '''gently''' an inch, and slid the top of the washer away from me, removed top. -then i just reseated the pink wire connector (i reseated them all). -problem solved, for now. -must be a poor connection (vibration?). -cost me $73 for the latch i didn't need, hope i save you $.
+-(Kenmore HE3)…same thing... mine would not lock, error 'DL'... i replaced the door latch mechanism, which did '''not''' solve the problem. -i removed the three torx screws from the top-back of the unit, lifted the back cover up '''gently''' an inch, and slid the top of the washer away from me, removed top. -then i just reseated the pink wire connector (i reseated them all). -problem solved, for now. -must be a poor connection (vibration?). -cost me $73 for the latch i didn't need, hope i save you $.
--update 1/20/18:
+-update 1/20/18:
+
-eventually i had to re-solder the board where the connectors make contact, which involved removing the board and adding a bit of solder to each of the contact points on the board, been years now without a fault.

Status:

open

Bewerkt door: julian clark

Tekst:

-same thing... mine would not lock, error 'DL'... i replaced the door latch mechanism, which did '''not''' solve the problem. -i removed the three torx screws from the top-back of the unit, lifted the back cover up '''gently''' an inch, and slid the top of the washer away from me, removed top. -then i just reseated the pink wire connector (i reseated them all). -problem solved, for now. -must be a poor connection (vibration?). -cost me $73 for the latch i didn't need, hope i save you $.
+
+-update 1/20/18:
+-eventually i had to re-solder the board where the connectors make contact, which involved removing the board and adding a bit of solder to each of the contact points on the board, been years now without a fault.

Status:

open

Origineel bericht door: julian clark

Tekst:

-same thing... mine would not lock, error 'DL'... i replaced the door latch mechanism, which did '''not''' solve the problem.  -i removed the three torx screws from the top-back of the unit, lifted the back cover up '''gently''' an inch, and slid the top of the washer away from me, removed top. -then i just reseated the pink wire connector (i reseated them all). -problem solved, for now.  -must be a poor connection (vibration?).  -cost me $73 for the latch i didn't need, hope i save you $.

Status:

open