Inleiding

How to repair a loose power button.

Remove stylus and SD card. Using T-5 torx driver, remove 4 back panel screws.
  • Remove stylus and SD card.

  • Using T-5 torx driver, remove 4 back panel screws.

  • The screws are small and can be lost easily. Be sure to place them in a secure area.

Voeg opmerking toe

Begin to remove back cover by inserting the plastic opening tool under the usb and power input slots. Continue by sliding the plastic opener to the right at the markers shown until the cover releases. Continue by sliding the plastic opener to the right at the markers shown until the cover releases.
  • Begin to remove back cover by inserting the plastic opening tool under the usb and power input slots.

  • Continue by sliding the plastic opener to the right at the markers shown until the cover releases.

I think it's better to open from the right, not the left. The right will separate if you lever the metal back to the outside and push the plastic to the inside. The lft is more like a inge and would damage more easily.

Just my $0.02.

Yishai Sered - Antwoord

Your device may not have a screen protector. If not, you do not need to complete step three. Please move on to step four. Remove screen protector by lifting hinge out of plastic housing.
  • Your device may not have a screen protector. If not, you do not need to complete step three. Please move on to step four.

  • Remove screen protector by lifting hinge out of plastic housing.

  • Remove top cover by gently pulling away from the device with plastic tool

Voeg opmerking toe

Mac RAM Kits
Versnel je Mac. Breid zijn geheugen uit.
Mac RAM Kits
Haal meer megabytes uit je Mac.
Carefully remove motherboard from the standoffs without damaging the LCD flex connector. Using spudger( the black pencil-like tool shown in picture two), unlock both sides of the flex connector block (shown in the purple boxes in picture two) by pushing down.
  • Carefully remove motherboard from the standoffs without damaging the LCD flex connector.

  • Using spudger( the black pencil-like tool shown in picture two), unlock both sides of the flex connector block (shown in the purple boxes in picture two) by pushing down.

  • Remove motherboard completely.

  • Metal washers may pop out of the device during this step

Voeg opmerking toe

Remove buttons using fingers. Gently flex frame to release screen from plastic frame. Lift out screen.
  • Remove buttons using fingers.

  • Gently flex frame to release screen from plastic frame.

  • Lift out screen.

Voeg opmerking toe

Congratulations! You have successfully taken apart a Palm Tungsten E.
  • Congratulations! You have successfully taken apart a Palm Tungsten E.

Voeg opmerking toe

Follow steps 1 through 4 in the Tungsten E Teardown

Voeg opmerking toe

On the motherboard, find the power button near the upper right corner.
  • On the motherboard, find the power button near the upper right corner.

  • Check for disconnection of the power button.

Voeg opmerking toe

Use soldering iron to reattach the damaged power button to the motherboard.
  • Use soldering iron to reattach the damaged power button to the motherboard.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Kathleen Hix

Lid sinds: 21-01-10

49 Reputatie

2 handleidingen geschreven

Team

Cal Poly, Team 13-22, Maness Winter 2010 Lid van Cal Poly, Team 13-22, Maness Winter 2010

CPSU-MANESS-W10S13G22

4 Leden

4 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 1

Afgelopen 30 Dagen: 3

Altijd: 4,665