Repareer je spullen Gemeenschap Winkel

Repair guides and troubleshooting for the Whirlpool Quiet Partner II insulated dishwasher.

53 Vragen Bekijk alle

Opties

How do I reset my Quite Partner II Dishwasher

My Quiet Partner II dishwasher is not working - the control panel is no longer lit up. I am having a difficult time trying to find out how to Reset it with the correct control panel button sequence for this model. I believe it is hard-wired so I have checked the breakers in my basement. I have pushed some buttons and the lights came on and off but not working. and When I push the cancel button it comes on -:O) instead of the start button and the washing selections. Help! :O)

Beantwoord deze vraag Dit probleem heb ik ook

Is dit een goede vraag?

Ja Nee
Score 1
4 opmerkingen

Hi,

What is the model number of the dishwasher?

door

Model #Du1055xtvq8

door

Hi @stihl209

Did you try the Most Helpful Answer below, you didn't say?

door

I have power to the unit but no lights. Model DU950PWKQ1. I tried the reset as described with no success

door

Voeg een opmerking toe

6 Antwoorden

Filteren op:
Meest nuttige Nieuwste Oudste
Het nuttigste antwoord

Opties

Judy Doughty some of this will depend on your DW exact model. In general to reset the Quiet Partner II you:

Open the DW door

Push "heated dry," "normal," "heated dry" and "normal" in quick succession. immediately after this close the dishwasher door.

Was dit antwoord nuttig?

Ja Nee
Score 13

21 opmerkingen:

Thank you it worked. Dishwasher is up and running. DT

door

@daybreak1964 good job and thanks for letting us know!

door

It didnt work for me .. Any other ideas ?? Please

door

@Wanda Reddick

What is the model number of the dishwasher?

door

I had success with pressing both buttons at the same time, twice. Then closing the door. I may have even closed the door as I was pushing the buttons for the 2nd time.

door

16 commentaren meer tonen

Voeg een opmerking toe

Opties

Turn off the power. Open the dishwasher, take out the top 6 screws. The top control panel should pull away from the dishwasher. Pop off the plastic cover inside to expose the circuit board. Disconnect the 14 or 16 pin ribbon cable. Turn the power on. With the power on, carefully reconnect the ribbon cable. Reassemble your dishwasher. My dishwasher works again for me!šŸ˜€

Was dit antwoord nuttig?

Ja Nee
Score 2

3 opmerkingen:

The pin ribbon cable approach worked for me. Thanks very much

Used a Torx 10 bit to remove and tighten the screws.

Pressing buttons in different manners hadn't been successful

According to dishwasher's serial number and information I obtained from the Internet, the Quiet Partner II was manufactured in 2010.

door

The pin ribbon cable worked for us!

Pushing the buttons did not work for us.

Thanks

door

I popped open the cover, the ribbon pin was permanently attached and I couldn't remove it. I jiggled it and a couple of other connections, cleaned up a bit and closed it up. Now the dishwasher is working again! The only issue is that on the left side, the Pots&Pans, Normal, and Light lights remain dimly glowing even when the DW is completely off. I never noticed this before. Is this a normal thing, or is it something for me to be concerned about?

door

Voeg een opmerking toe

Opties

I had success with pressing both buttons at the same time, twice. Then closing the door. I may have even closed the door as I was pushing the buttons for the 2nd time.

Was dit antwoord nuttig?

Ja Nee
Score 0

1 Opmerking:

I have a whirlpool gold DW model # GU1500XTKT0 not operating and have a constant flashing rinse only light. Any ideas that I may try?

door

Voeg een opmerking toe

Opties

Normal wash, light wash and off/reset lights are flashing at same time. No other buttons will work.

Was dit antwoord nuttig?

Ja Nee
Score 0

2 opmerkingen:

This worked for me as well! Thank you!

door

Same issue here! I turned the breaker off and pulled the chipboard out unplugging it completely, put it all back together and it worked just fine!

door

Voeg een opmerking toe

Opties

My dishwasher is flashing on the normal wash and will not come on

Was dit antwoord nuttig?

Ja Nee
Score 0

2 opmerkingen:

Same issue here! I turned the breaker off and pulled the chipboard out unplugging it completely, put it all back together and it worked just fine! Sometimes just turning the breaker off for 30 seconds will reset it.

door

I posted same issue above but now see you have dealt with this already. Is the CPU board behind the inside door panel? Removing i think 14 screws will allow me access?

door

Voeg een opmerking toe

Opties

Iā€™m just getting all lights on with no response to any button being pushed after doing the heated dry/normal push reset. Any ideas what could be going on?

Was dit antwoord nuttig?

Ja Nee
Score 0

1 Opmerking:

Hi,

What is the model number of the dishwasher?

Have you tried disconnecting the power to the dishwasher for 5 minutes and checked if that reset it?

door

Voeg een opmerking toe

Voeg je antwoord toe

Judy Doughty zal eeuwig dankbaar zijn.
Weergavestatistieken:

Afgelopen 24 uren: 40

Afgelopen 7 dagen: 257

Afgelopen 30 dagen: 1,174

Altijd: 34,273