No power no detect on itunes from a good batt

Question

iPhone 6

Repair information and guides for the iPhone 6 that was released on September 19, 2014. Model Numbers: A1549, A1586, and A1589

4994 Vragen Bekijk alle

Nathan Pelling @nathanpelling

Rep: 13

2

Gepost: 10 apr. 2017

Opties

No power no detect on itunes from a good batt

HI guys,

I have an iPhone 6 in for repair and its got me a little stuck.

iHave a known good working battery hooked up and no detection by itunes or CPU isnt getting warm.

Took the following voltages thus far VCC_main from CF 5202 ( 1.1v) these are all taken with direct power from mains via charging dock.

Values from around tristar

C1299 on PP3v3 reads (1.33v)

C1704 on tristar PIN ( 3.36v)

C1738 on tristar by pass ( 1.90v)

C1700 PP3V0 (1.420)

SOme values from BATT VCC

C1695 (1.1v)

Any help in right direction will be much appreciated.

Kind Regards

Nathan

Beantwoord! Bekijk het antwoord Dit probleem heb ik ook

Is dit een goede vraag?

Ja Nee

Score 0

2 opmerkingen

Changed tristar. Still nothing, no heat being generated at all through the board.

10 apr. 2017 door Nathan Pelling

PP5V0 - is down at 3-4.2v which is a little low at C1408

10 apr. 2017 door Nathan Pelling

Voeg een opmerking toe

2 Antwoorden

Gekozen oplossing

Minho @refectio

Rep: 221,5k

15

290

807

Gepost: 11 apr. 2017

Opties

Some of those test points are not really important. Focus on the main power rails first (PP_BATT_VCC, PP_VCC_MAIN and PP5V0_USB). Seeing as how those rails are not where they should be, that's what you must troubleshoot first.

Either your PMIC is bad (hence all of the low voltage readings) or something is dragging it down (it would be hot though). So check all your main power rails (see above) and then check all of the rails generated by the PMIC. Note which ones are there vs which ones are low vs which ones are possibly shorted and then take your troubleshooting forward.

Get back to us with your findings.

Was dit antwoord nuttig?

Ja Nee

Score 3

5 opmerkingen:

Hi mate,

Thanks for response.

I have the following readings

vcc main - 2.3/2.4v

vcc batt - 2.4v

pp5v0 - 3.4- 4.4v flucuates

PP3v3-acc ( not sure if this matters ) - 0V

Mains power & dock connected

PS. If I say something stupid bare with me im still learning haha. But I have a fair idea of what im doing

t

11 apr. 2017 door Nathan Pelling

Going off lines from scematic now -

PP gpu/1.1v - 0V

11 apr. 2017 door Nathan Pelling

pp tristar pin - 4.3/4v

11 apr. 2017 door Nathan Pelling

PMC is what I would've suggested next. Thanks @refectio. Never done one of those. And aren't there ...3? Pretty sure there's definately 2. And you'll want to test those circuits as well

11 apr. 2017 door iMedic

Yep

Apple/Dialog 338S1251-AZ Power Management IC

Qualcomm PM8019 Power Management IC

Also, unrelated, when someone has trouble hearing, and you try replacing the front camera flex, and that doesn't take. Then it's either the socket, or the Cirrus Logic 338S1201 Audio Codec?

11 apr. 2017 door iMedic

Voeg een opmerking toe

Changed tristar. Still nothing, no heat being generated at all through the board. — Nathan Pelling
Hi mate,

Thanks for response.

I have the following readings

vcc main - 2.3/2.4v

vcc batt - 2.4v

pp5v0 - 3.4- 4.4v flucuates

PP3v3-acc ( not sure if this matters ) - 0V

Mains power & dock connected

PS. If I say something stupid bare with me im still learning haha. But I have a fair idea of what im doing

t — Nathan Pelling
PMC is what I would've suggested next. Thanks @refectio. Never done one of those. And aren't there ...3? Pretty sure there's definately 2. And you'll want to test those circuits as well — iMedic
Yep

Apple/Dialog 338S1251-AZ Power Management IC

Qualcomm PM8019 Power Management IC

Also, unrelated, when someone has trouble hearing, and you try replacing the front camera flex, and that doesn't take. Then it's either the socket, or the Cirrus Logic 338S1201 Audio Codec? — iMedic