Israel

@israel

Israel

3.589	Reputatie
150	Oplossingen
0	Handleidingen
Lid sinds 28-07-15

Electronics - My hobby and my job!

- Specialize in Apple and Samsung Devices

- Board repair such as pry damage, connectors, water damage, ICs, Backlight...

- LCD Refurbishing.

Stemmen

Electronics is my career and hobby!

Background:

I am and Electrical Engineer by trade. Decided to study my M.S. in Biomedical Engineering which I recently completed. Now pursuing my PhD for fun.

How did I get into the repair business?

One of my friends broke her iPhone and decided to give it a shot. I loved the experience and kept doing it on the side while going to school. I asked her to keep the screens that came in the toolkit instead of money... haha

A few months later I opened my first shop in Memphis, TN and it has been a very fun experience. This was in 2012 so I have been in the industry for a little while now. I am very experienced with refurbishing and micro soldering, so feel free to reach out if you have any questions!

STS Repair has recently opened its Board Repair Services (Mail-ins).

You are welcome to check out our website at www.stsrepair.com!

You can contact me at cs@stsrepair.com

Demontages waar ik aan gewerkt heb

iPhone 6s Display Teardown

Uitgevoerde reparaties

Adding images to an existing question

Antwoorden

Antwoord op "How to put a screw hole back after long screw damage" 18-11-17
You can solder it back on. Just place it and sit your soldering iron on top of the socket, it will heat enough to solder itself back on.
Antwoord op "Broke the lightning connector - parts stuck in logicboard" 18-11-17
It seems like corrosion made those connectors stick. You have to replace that connector and inspect around logic board to make sure there is no more damage on the logic board. If you are not a micro solderer id recommend finding a shop who can help!
Antwoord op "Side Clips Not Holding on Replacement Screen" 18-11-17
Start by the top clips on the screen. Make sure they go into the frame. Then you do the sides and make sure they go in. If they are not easily going in and the frame is not bent you can help sliding a knife looking tool to help those clips to slide into place. Lastly, do the bottom. Triple check for bent frame, otherwise you will be breaking that screen!
Antwoord op "Need Replacement Coax Wifi Connector - Any place to buy?" 18-11-17
Sometimes if you cant find in a marketplace you can buy a "dead" motherboard. I usually keep some to be donor boards.
Antwoord op "How much does a new screen cost" 18-11-17
It depends where you buy, however I'd say around $150 for the part.
Antwoord op "Why is this happening?" 16-11-17
Have you tried reset all settings?
Antwoord op "White lines on screen" 15-11-17
Jack, This could have happened due to the phone being dropped as well. If no repairs were performed a drop could cause the flex cables to lose contact with the LCD contact glass causing the glitch you describe. You have to replace the screen in this case for a successful repair!
Antwoord op "New battery doesn't work" 14-11-17
It seems like you might have received a faulty battery. I would try another one!!
Antwoord op "Charge port not working" 14-11-17
You would be looking at the Tristar IC. Let me know if you need help!
Antwoord op "iPhone is on but no screen" 14-11-17
Hey there! haha Thanks Mayer, we all learn things everyday. Savas, you can either have a no backlight issue or a not image issue. It sounds like no backlight is the issue even though you say shining a light doesn't help. It is hard sometimes to see image, usually when you are turning on the phone and the apple logo is shown the best time to identify backlight issue. If it is a non image issue most likely there are small square components on top of the LCD connector that could be knocked off easily. However backlight circuit can be affected when working on a phone with a plugged battery, so make sure to ALWAYS disconnect the battery first! I can look at it if you want to mail it in ;)

Pagina 1 van 15

HTC One M9 Teardown 10-11-17

Metal spudger is never a good idea against motherboard. Use heat gun for a FEW seconds while you wiggle board out. It will come off easily!
HTC One M9 Teardown 10-11-17

Guys.. COME ON.. BATTERY FIRST before connector.
HTC One M9 Teardown 10-11-17

Take the SIM card and the SD Card before the next STEP!!
iPhone 6s Display Teardown 08-02-16

Go to step 4 on this tutorial. You can swap it out with a different one if needed.
iPhone 6s Display Teardown 08-02-16

What do you mean spot weld? The ear speaker mesh is glued around the ear speaker hole, you can purchase these individually.
iPhone 6s Display Teardown 08-02-16

The backlight power flex is still soldered to the flex cable like other models. The only difference is that the force touch is part of the backlight.
iPhone 6s Display Teardown 08-02-16

Dylan, if this is due to screen being refurbished keep in mind the "assembling" of the screen in the refurbishing process is done in a clean dust free environment.