Deze gebruiker heeft hun profiel nog niet ingevuld.
Vragen
Hey everyone, I replaced two ipad mini digitizers. These were the kind you have to solder. I used a stereoscopic...
Meer informatieAntwoorden
We have two of these with this problem. Interestingly, they both have i7 processors. We have a bunch of these with i5 and none of these have charging problems. Any luck with this? We are still searching for an answer.
Meer informatieTry a reset. Hold down the power button and the home button simultaneously until you see the apple logo. If this doesn't work, you likely blew a fuse. You can google the fuse locations and replace it or bridge it with a bit of solder. Good luck!
Meer informatieBuy it on ebay.com http://www.ebay.com/sch/i.html?_trksid=m...-810+digitizer&_sacat=0 Here's a link to a video showing the replacement of a similar device. If you haven't worked on these before consider taking it to a local repair shop and save yourself much grief... http://www.youtube.com/watch?v=F4Ly87OLC...
Meer informatieI had this problem and used electrician's tape to tape of the exposed metal around the bottom and it solved the problem. I theorized it was shorting when metal touched metal. But I've also read that magnets can cause this if they get to close to the digitizer so if you put the rare earth magnets back onto the glass' underside, make sure they are away from the digitizer itself. Good luck!
Meer informatieIf you can smell it, you need to replace it. We've had an iphone 4s battery explode in our shop. Not something you want to happen ;)
Meer informatieIf the multimeter shows a reading on the pins that connect to the battery then you know you have current flowing through the board and making it to charge the battery. I check this to rule out fried board quickly. Also, an easy quick check is to look in all the USB ports and make sure none of them are damaged. if two pins in any of the USB ports are bent up and touching each other the computer will short and not start. Simply bending them so they no longer touch would resolve such an issue. Good luck!
Meer informatieTry putting a thin piece of plastic on top of the flex cable as you slide it in. This will provide more downward pressure. Although I have never used this technique for ipad I have successfully used this on PS3 drive flex cables and keyboard cables in laptops. The trick is to find a thin hard plastic and then cut it to the exact width of the flex cable. Good luck!
Meer informatieLooks like some of these presoldered digitizers are coming without the magnetic sensors which are located on the home button flex cable. After purchasing two of these I ended up having to harvest the OEM home button flex and moving it to the purchased digitizer. I sent a picture to the seller showing the issue. I figured I ought to put it up for your viewing as well. Note that this is showing one of the sensors near the home button. There is another sensor near the soldering joints which is a bit smaller. You can see how they work together in the youtube video above. Thanks, Mark T.
Meer informatieIts just to the left of the connector if holding the device with home button towards you. Under a scope you will be able to see it missing. If you don't have the resistor, you may want to just put a solder ball to bridgethe connection. DDon't quote me but I think a bridge of solder will work fine and not cause any problems.. That device went back with customer shortly after and unfortunately I never got photos. Good luck! - Mark
Meer informatieHere is an update in case someoneelse finds themselves with the same problem. I found a small resistor that had come off next to the battery push connector. Was able to resoler it and battery charged again. Barely visible without microscope.
Meer informatieCommentaar Gids
System update partition is 12GB but the files that need to go into A and B folders will not fit in this partition. It is slightly too small. :(
Mark
@mark67264
211
Reputatie
10
Oplossingen
0
Handleidingen
Lid sinds 03/29/13
Team
$99 PC Repair Centers
We Repair phones, consoles, computers, tablets etc
Stemmen
1
0