daniel

@tech_ni

daniel

8.161	Reputatie
607	Oplossingen
0	Handleidingen
Lid sinds 06-08-17

Stemmen

Vragen

Stuck at apple logo 19-12-19
After lcd fpc replacement phone booted fine. Now stuck on apple logo and power supply showing 0.33 amps when button is...
Red light a beep 07-05-19
Has anyone found a fix for ghd platinum red light and beep yet
Need schematics urgently please 03-04-19
This laptop won't turn on after a power cut. When the charger is plugged in the power brick light goes out. I felt a...
not charging and taking along time to boot to home screen 18-01-19
@refectio i have an issue with this iphone 6. when i got it, it wouldnt boot. on dc and charger with battery disconnected...
no power even after both power ics changed 24-08-18
so i have an s6 edge+ no power, replaced both power ic’s. getting around 3.5v in both locations but not turning on and no...
vdd main short but no heat 14-07-18
so i have an iphone 7 in this morning and as title says i have a vdd main short, wire soldered on and drawing 2 amps but...
dim backlight after liquid damage 24-05-18
i have a macbook air 820-3437 which was liquid damaged, doa. corrosion was around smc and u7700, reballed smc and it...
about gsx account not phone 23-05-18
does anyone have an apple gsx account that can help me figure out how to get an account
will only boot to safe mode 22-04-18
i have a ps4 that wont boot when the power button is pressed just blue pulsing light, yet it will boot into safe mode and...
iPhone 6 not booting 19-04-18
im having an issue with an iphone 6, when i got it, it was bootlooping, now i have replaced pmic, tristar and tigris. but...

Pagina 1 van 4

Antwoord op "PSU connector ripped from motherboard" 15-01-20
Scrape the vias until you see copper. Where the bottom 2 arrows point. The other pad is there and the 1 with no via is probably ground so can be jumped from the ground side of the capacitor. Use epoxy to attach the connector then solder wires from the vias to the connector pins. Once done add some more epoxy for strength.
Antwoord op "iPhone stuck in boot loop after Apple logo replacement" 12-01-20
Ok if you were adding an led apple logo, then smelt burning and stopped. How did you eventually add it.
Antwoord op "iPhone XR Boot loop after water damage" 09-01-20
Have you tried it with just the lcd connected, no cameras etc. Could also be a screen issue. Remember the logic board is 2 seperate pcbs soldered together and you would only see damage when they are seperate.
Antwoord op "Why does my ipad not work after digitizer,LCD and battery replacement?" 03-01-20
Check for pry damage around the connectors. Also download 3utool, connect the ipad and see if it detects it as you can use this to kick it out of recovery mode.
Antwoord op "MacBook Pro No backlight" 03-01-20
Change the fuse. You shouldn't just get voltage on 1 side.
Antwoord op "Missing resistor near charging port" 24-12-19
There is no photo attached.
Antwoord op "Anyone know of a screw mat for the iPhone SE?" 24-12-19
Is the 5s not pretty much the same.
Antwoord op "Microphone repair iPhone 6" 19-12-19
The microphone is on the charge port board. iPhone 6 Lightning Connector Assembly Replacement.
Antwoord op "iPhone 6 kills battery every time it dies" 19-12-19
If it drains the battery quickly get your friend to replace tristar.
Antwoord op "Mobile data signal horrible after repair" 19-12-19
Sounds like a bad port if you get good reception with the old 1

Pagina 1 van 61

Reputatieverdeling

Gebeurtenis	Telling	Delta
Post is positief beoordeeld	449	5360
Antwoord geaccepteerd	107	3210
Goedgekeurd antwoord	4	40
Beoordeelde een post negatief	1	-2
Post is negatief beoordeeld	8	-48
Jouw opmerking is verwijderd vanwege markeringen	4	-400