/
Mijn werkbank

Krijg snel toegang tot handleidingen, onderdelen en antwoorden voor jouw apparaten

DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
Lid worden
Inloggen
Word lid van 's werelds grootste reparatiegemeenschap
OnderdelenHandleidingenAntwoorden
Bewerken
iPod 2nd Generation Logic Board Replacement

iPod 2nd Generation Logic Board Replacement

iRobot

iRobot en een andere bijdrager

Voor het laatst geüpdatet op August 16, 2022

Geen schatting
Gemiddeld

Inleiding

Ga naar stap 1

Your iPod's motherboard controls just about everything on the iPod.

Wat je nodig hebt

Gereedschap

  1. iPod 2nd Generation Logic Board Replacement, Rear Panel: stap 1, afbeelding 1 van 1

    • Before opening your iPod, ensure that the hold switch is in the locked position.

    Bewerken

  2. iPod 2nd Generation Logic Board Replacement: stap 2, afbeelding 1 van 1

    • Opening the iPod can be challenging. Don't get discouraged if it takes a few tries before the iPod is opened.

    • Insert a plastic iPod opening tool in the seam between the white plastic front and metal back of the iPod. Once you've inserted the tool, run it along the seam to free the five tabs holding the iPod together.

    Bewerken

  3. iPod 2nd Generation Logic Board Replacement: stap 3, afbeelding 1 van 1

    • Continue to run the opening tool along the side of the case until all five tabs have been released.

    Bewerken

  4. iPod 2nd Generation Logic Board Replacement: stap 4, afbeelding 1 van 1

    • Work around the corner of the iPod and release the two tabs holding the iPod together near the dock connector.

    Bewerken

  5. iPod 2nd Generation Logic Board Replacement: stap 5, afbeelding 1 van 1

    • Free the five tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.

    Bewerken

  6. iPod 2nd Generation Logic Board Replacement: stap 6, afbeelding 1 van 1

    • Lift the rear panel away from the iPod, making sure it doesn't catch on the headphone jack.

    Bewerken

  7. iPod 2nd Generation Logic Board Replacement, Hard Drive: stap 7, afbeelding 1 van 1

    • Peel up the metallic tape attached to the top of the battery.

    Bewerken

  9. iPod 2nd Generation Logic Board Replacement: stap 8, afbeelding 1 van 1

    • Lift the battery up from the hard drive and lay it next the the iPod (it is still connected to the logic board).

    Bewerken

  10. iPod 2nd Generation Logic Board Replacement: stap 9, afbeelding 1 van 1

    • Carefully disconnect the orange ribbon cable from the hard drive.

    • If the cable doesn't come free easily, it may be helpful to gently wiggle the cable from side to side.

    • Lift the hard drive out of the iPod.

    Bewerken

  11. iPod 2nd Generation Logic Board Replacement, Hard Drive Cable: stap 10, afbeelding 1 van 1

    • For the following step, you only need to move the locking bar about 2 mm. Pushing too hard or too far will damage the connector.

    • Loosen the connector by pulling the brown locking bar toward the hard drive cable using the tips of your fingers.

    Bewerken

  12. iPod 2nd Generation Logic Board Replacement: stap 11, afbeelding 1 van 1

    • Slide the hard drive cable out of its connector.

    Bewerken

  13. iPod 2nd Generation Logic Board Replacement, Display: stap 12, afbeelding 1 van 1

    • Lift the blue hard drive mounting bracket out of the iPod.

    Bewerken

  14. iPod 2nd Generation Logic Board Replacement: stap 13, afbeelding 1 van 1

    • Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

    Bewerken

  15. iPod 2nd Generation Logic Board Replacement: stap 14, afbeelding 1 van 1

    • Like the hard drive connector, for the following step, you only need to move the connector about 2 mm. Pushing too hard or too far will damage the connector.

    • Loosen the touch wheel connector by pulling the brown locking bar toward the side of the iPod using the tips of your fingers.

    Bewerken

  16. iPod 2nd Generation Logic Board Replacement: stap 15, afbeelding 1 van 1

    • Remove the 8 T6 Torx screws from the logic board.

    Bewerken

  17. iPod 2nd Generation Logic Board Replacement: stap 16, afbeelding 1 van 1

    • Lift the logic board up enough to disconnect the orange touch wheel cable.

    • Lift the logic board out of the iPod.

    Bewerken

  18. iPod 2nd Generation Logic Board Replacement: stap 17, afbeelding 1 van 1

    • Note the location of the four white plastic tabs securing the display to the logic board. These tabs must be released before the display can be removed.

    Bewerken

  19. iPod 2nd Generation Logic Board Replacement: stap 18, afbeelding 1 van 1

    • Use a spudger or your finger to free the four white plastic tabs indicated in the previous picture.

    Bewerken

  20. iPod 2nd Generation Logic Board Replacement: stap 19, afbeelding 1 van 1

    • Use a spudger to carefully disconnect the display ribbon cable from beneath the scroll wheel.

    • Lift the display off the logic board.

    Bewerken

  21. iPod 2nd Generation Logic Board Replacement, Logic Board: stap 20, afbeelding 1 van 1

    • Logic board remains.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

2 andere personen hebben deze handleiding voltooid.

Auteur

met 1 andere bijdrager

iRobot

Lid sinds: 09/24/09

1 Reputatie

636 handleidingen geschreven

Medailles: 36

+33 andere badges

4 opmerkingen

I wish all iPods were this easy to fix!

Donald Fournier - Antwoord

I just replaced a battery and Logic Board in an iPod 2nd Generation. Totally easy; No soldering necessary. The hardest part was waiting for the Logic Board in the mail.

Donald Fournier - Antwoord

My 2G will not connect to either windows or macos via FW. I have cleaned the connector, checked the logic board for obvious damage, etc. My 1G connects to the same computers just fine. The 2G otherwise works, passes all diagnostics (seems to), and wakes up and charges when I plug it in to the computer. Do I need a new logic board? Otherwise, I am thinking of just manually transferring my music to the drive and living with it.

Rusty Lingenfelter - Antwoord

Hi,

try to replace the hard drive from your 1G first ans see if this works.

Please let me know.

Thanks,

Georg Balzereit -

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 3

Afgelopen 30 dagen: 12

Altijd: 10,029