Repareer je spullen

Recht op reparatie

Onderdelen & Gereedschap

iPod 2nd Generation Display Replacement

Geschreven door: iRobot (en 2 andere bijdragers)
  • Reacties: 0
  • Favorieten: 3
  • Voltooide reparaties: 1

Moeilijkheid

Gemiddeld

Stappen

19

Tijd vereist

Stel een tijd voor??

Secties

4

Markeringen

0

Inleiding

Replace a cracked or faulty display.

Gereedschap

Koop deze gereedschappen

Onderdelen

Geen onderdelen opgegeven.

  1. Before opening your iPod, ensure that the hold switch is in the locked position.

    • Before opening your iPod, ensure that the hold switch is in the locked position.

    Bewerken

  2. Opening the iPod can be challenging. Don't get discouraged if it takes a few tries before the iPod is opened.

    • Opening the iPod can be challenging. Don't get discouraged if it takes a few tries before the iPod is opened.

    • Insert a plastic iPod opening tool in the seam between the white plastic front and metal back of the iPod. Once you've inserted the tool, run it along the seam to free the five tabs holding the iPod together.

    Bewerken

  3. Continue to run the opening tool along the side of the case until all five tabs have been released.

    • Continue to run the opening tool along the side of the case until all five tabs have been released.

    Bewerken

  4. Work around the corner of the iPod and release the two tabs holding the iPod together near the dock connector.

    • Work around the corner of the iPod and release the two tabs holding the iPod together near the dock connector.

    Bewerken

  5. Free the five tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.

    • Free the five tabs holding the iPod together on the other side. You may be able to free the tabs by gently wiggling the front panel of the iPod.

    Bewerken

  6. Lift the rear panel away from the iPod, making sure it doesn't catch on the headphone jack.

    • Lift the rear panel away from the iPod, making sure it doesn't catch on the headphone jack.

    Bewerken

  7. Peel up the metallic tape attached to the top of the battery.

    • Peel up the metallic tape attached to the top of the battery.

    Bewerken

  8. Nintendo Switch-kits

    Een snelle oplossing die je weer mee laat doen

    Koop Switchkits

    Nintendo Switch-kits

    Een snelle oplossing die je weer mee laat doen

    Koop Switchkits

  9. Lift the battery up from the hard drive and lay it next the the iPod (it is still connected to the logic board).

    • Lift the battery up from the hard drive and lay it next the the iPod (it is still connected to the logic board).

    Bewerken

  10. Carefully disconnect the orange ribbon cable from the hard drive.

    • Carefully disconnect the orange ribbon cable from the hard drive.

    • If the cable doesn't come free easily, it may be helpful to gently wiggle the cable from side to side.

    • Lift the hard drive out of the iPod.

    Bewerken

  11. For the following step, you only need to move the locking bar about 2 mm. Pushing too hard or too far will damage the connector.

    • For the following step, you only need to move the locking bar about 2 mm. Pushing too hard or too far will damage the connector.

    • Loosen the connector by pulling the brown locking bar toward the hard drive cable using the tips of your fingers.

    Bewerken

  12. Slide the hard drive cable out of its connector.

    • Slide the hard drive cable out of its connector.

    Bewerken

  13. Lift the blue hard drive mounting bracket out of the iPod.

    • Lift the blue hard drive mounting bracket out of the iPod.

    Bewerken

  14. Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

    • Carefully disconnect the white battery connector from the logic board. Be sure to pull only on the connector itself and not on the cables.

    Bewerken

  15. Like the hard drive connector, for the following step, you only need to move the connector about 2 mm. Pushing too hard or too far will damage the connector.

    • Like the hard drive connector, for the following step, you only need to move the connector about 2 mm. Pushing too hard or too far will damage the connector.

    • Loosen the touch wheel connector by pulling the brown locking bar toward the side of the iPod using the tips of your fingers.

    Bewerken

  16. Remove the 8 T6 Torx screws from the logic board.

    • Remove the 8 T6 Torx screws from the logic board.

    Bewerken

  17. Lift the logic board up enough to disconnect the orange touch wheel cable.

    • Lift the logic board up enough to disconnect the orange touch wheel cable.

    • Lift the logic board out of the iPod.

    Bewerken

  18. Note the location of the four white plastic tabs securing the display to the logic board. These tabs must be released before the display can be removed.

    • Note the location of the four white plastic tabs securing the display to the logic board. These tabs must be released before the display can be removed.

    Bewerken

  19. Use a spudger or your finger to free the four white plastic tabs indicated in the previous picture.

    • Use a spudger or your finger to free the four white plastic tabs indicated in the previous picture.

    Bewerken

  20. Use a spudger to carefully disconnect the display ribbon cable from beneath the scroll wheel.

    • Use a spudger to carefully disconnect the display ribbon cable from beneath the scroll wheel.

    • Lift the display off the logic board.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Auteur

met 2 andere bijdragers

iRobot

Lid sinds: 24-09-09

1 Reputatie

648 handleidingen geschreven

Badges: 35

+32 andere badges

0 Opmerkingen

Voeg een opmerking toe

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 3

Afgelopen 30 dagen: 8

Altijd: 6,747