Repareer je spullen Gemeenschap Winkel

Zoomer Jurassic World Indominus Rex Motherboard Replacement

Inleiding

Motherboard is the most important component of a Zoomer Jurassic World Indominus Rex. If all else fails, we can always replace the motherboard. Knowing how to solder before attempting this guide is extremely encouraged. Details about soldering technique guide can be found at the last step of this guide.

Wat je nodig hebt

  1. Zoomer Jurassic World Indominus Rex Motherboard Replacement, Back Cover: stap 1, afbeelding 1 van 1

    • Turn off and unplug Zoomer Jurassic World Indominus Rex from any power source before doing replacements.

    • Remove all eight (8) 9.3mm Phillips screws using Phillips #1 screwdriver.

    Vertaal

  2. Zoomer Jurassic World Indominus Rex Motherboard Replacement: stap 2, afbeelding 1 van 2 Zoomer Jurassic World Indominus Rex Motherboard Replacement: stap 2, afbeelding 2 van 2

    • Pry apart the back cover of the Jurassic Indominus Rex and the rest of the body using a spudger.

    • Do not take out the back cover immediately as it it still attached to the motherboard by a wire.

    Vertaal

  4. Zoomer Jurassic World Indominus Rex Motherboard Replacement: stap 3, afbeelding 1 van 2 Zoomer Jurassic World Indominus Rex Motherboard Replacement: stap 3, afbeelding 2 van 2

    • Disconnect the orange wire that connects the motherboard and the back cover.

    • Separate the back cover and the rest of the Zoomer Jurassic World Indominus Rex.

    • Gently press the tab on the side of the orange connector if you are having trouble disconnecting the wire.

    Vertaal

  5. Zoomer Jurassic World Indominus Rex Motherboard Replacement, Motherboard: stap 4, afbeelding 1 van 2 Zoomer Jurassic World Indominus Rex Motherboard Replacement, Motherboard: stap 4, afbeelding 2 van 2

    • Let the toy rest firmly on a flat surface before processing to the next step.

    • Gently pull each wire out of the connector on the motherboard. Use a set of tweezers, if necessary.

    Vertaal

  6. Zoomer Jurassic World Indominus Rex Motherboard Replacement: stap 5, afbeelding 1 van 2 Zoomer Jurassic World Indominus Rex Motherboard Replacement: stap 5, afbeelding 2 van 2

    • Remove the two (2) #0 7.5mm phillips screws from the left side of the motherboard.

    • Remove the one (1) 7.5mm #0 phillips screw from the right side of the motherboard.

    Vertaal

  7. Zoomer Jurassic World Indominus Rex Motherboard Replacement: stap 6, afbeelding 1 van 1

    • Use a soldering iron to remove the red and black wires from the motherboard .

    • Soldering technique guide from iFixit can be found here.

    • Use caution while soldering to avoid being burned.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 2 andere bijdragers

Anh Le

Lid sinds: 01/20/16

504 Reputatie

3 handleidingen geschreven

Medailles: 12

+9 andere badges

Team

USF Tampa, Team 10-3, Remmell Spring 2016 Lid van USF Tampa, Team 10-3, Remmell Spring 2016

USFT-REMMELL-S16S10G3

4 Leden

14 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 7

Altijd: 761