Inleiding

This repair guide will give you step by step instructions on how to remove the Macintosh PowerBook 1400c Monitor.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

Voeg opmerking toe

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

Voeg opmerking toe

Continue holding the latch then gently pull the battery out of the device.
  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

Voeg opmerking toe

Locate the CD-ROM Drive latch.
  • Locate the CD-ROM Drive latch.

Voeg opmerking toe

Slide the latch to the right to release the CD ROM drive.
  • Slide the latch to the right to release the CD ROM drive.

Voeg opmerking toe

Continue holding the latch then gently pull the CD-ROM Drive out of the device.
  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

Voeg opmerking toe

Locate the speaker cover.
  • Locate the speaker cover.

Voeg opmerking toe

Press firmly on each end of the speaker cover and slide it to the left.
  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - Antwoord

Gently lift the speaker cover to remove it.
  • Gently lift the speaker cover to remove it.

Voeg opmerking toe

Lift the keyboard up from the back using a spudger(wedge side).
  • Lift the keyboard up from the back using a spudger(wedge side).

Voeg opmerking toe

Gently lift the keyboard until only the ribbon cable remains attached.
  • Gently lift the keyboard until only the ribbon cable remains attached.

Voeg opmerking toe

Tilt the keyboard away from the screen.
  • Tilt the keyboard away from the screen.

Voeg opmerking toe

Locate the six screws that secure the heatsink.
  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - Antwoord

That isn't the HDD!

Dix Dox - Antwoord

Remove the six screws from the heatsink using the Philips #1 screwdriver.
  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

Voeg opmerking toe

Lift the heatsink from the side closest to the laptop screen.
  • Lift the heatsink from the side closest to the laptop screen.

Voeg opmerking toe

Remove the heatsink.
  • Remove the heatsink.

Voeg opmerking toe

Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.
  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

Voeg opmerking toe

Detach the ribbon cable.
  • Detach the ribbon cable.

Voeg opmerking toe

Remove the keyboard.
  • Remove the keyboard.

Voeg opmerking toe

Identify the right and left monitor end caps.
  • Identify the right and left monitor end caps.

Voeg opmerking toe

Pry off the end caps by putting a spudger between the monitor hinge and the end cap and prying outwards.
  • Pry off the end caps by putting a spudger between the monitor hinge and the end cap and prying outwards.

Voeg opmerking toe

Once the end cap has been loosened by the spudger, pull outwards on the end caps.
  • Once the end cap has been loosened by the spudger, pull outwards on the end caps.

Voeg opmerking toe

Completely remove both end caps.
  • Completely remove both end caps.

Voeg opmerking toe

Identify the 4 total screw under the end caps (2 under each end cap).
  • Identify the 4 total screw under the end caps (2 under each end cap).

    • The two outside 16mm long screws

    • The two inside 5.4mm long screws

Voeg opmerking toe

Lay the monitor all the way back.
  • Lay the monitor all the way back.

Voeg opmerking toe

Remove the 4 screws using the Phillips #0 screwdriver.
  • Remove the 4 screws using the Phillips #0 screwdriver.

Voeg opmerking toe

Identify the center cap of the monitor.
  • Identify the center cap of the monitor.

Voeg opmerking toe

Pry the center cap off by placing the spudger between the hinge and the center cap and prying upwards.
  • Pry the center cap off by placing the spudger between the hinge and the center cap and prying upwards.

Voeg opmerking toe

Detach the center cap completely.
  • Detach the center cap completely.

Voeg opmerking toe

Identify the one 12.6mm long screw under the center cap.
  • Identify the one 12.6mm long screw under the center cap.

Voeg opmerking toe

Remove the center screw with a Phillips #0 screwdriver.
  • Remove the center screw with a Phillips #0 screwdriver.

Voeg opmerking toe

Lift upwards on the metal cover under the screw.
  • Lift upwards on the metal cover under the screw.

Voeg opmerking toe

Completely remove the metal cover.
  • Completely remove the metal cover.

Voeg opmerking toe

Identify where the left and right monitor cords are attached to the logic board
  • Identify where the left and right monitor cords are attached to the logic board

    • The base of the left monitor cord

    • The base of the right monitor cord

Voeg opmerking toe

To detach the left monitor cord grab the left monitor cord at the base of the cord and pull vertically up.
  • To detach the left monitor cord grab the left monitor cord at the base of the cord and pull vertically up.

Voeg opmerking toe

Completely detach the left monitor cord from the logic board.
  • Completely detach the left monitor cord from the logic board.

Voeg opmerking toe

To detach the right monitor cord grab the right monitor cord at the base of the cord and pull vertically up.
  • To detach the right monitor cord grab the right monitor cord at the base of the cord and pull vertically up.

Voeg opmerking toe

Completely detach the right monitor cord from the logic board.
  • Completely detach the right monitor cord from the logic board.

Voeg opmerking toe

Completely remove the monitor from the computer.
  • Completely remove the monitor from the computer.

Voeg opmerking toe

Conclusie

Once the monitor has been removed, to attach the new monitor follow these instructions in reverse order.

2 andere personen hebben deze handleiding voltooid.

Taylor Chris

Lid sinds: 01-04-11

85 Reputatie

1 Handleiding geschreven

Team

Cal Poly, Team 10-39, Forte Spring 2011 Lid van Cal Poly, Team 10-39, Forte Spring 2011

CPSU-FORTE-S11S10G39

5 Leden

6 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 1

Afgelopen 30 Dagen: 9

Altijd: 2,485