Razer DeathAdder Chroma Scroll Wheel Replacement - iFixit reparatiehandleiding

Word lid van de reparatiegemeenschap - Account aanmaken

Inleiding

The Razer DeathAdder Chroma may experience faulty scroll wheel operation, such as a stuck wheel or having a non-functional scroll wheel click. This guide will show you how to access the scroll wheel for cleaning or replacement.

Wat je nodig hebt

1. Stap 1 Outer Casing
  Opening the mouse casing will void any warranty that exists for the mouse.
  
  Turn the mouse over so the bottom is facing up.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
2. Stap 2
  Use the blunt end of the spudger to pry the adhesive rubber pads from the top left and right edges.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
3. Stap 3
  Use a Phillips #0 screwdriver to remove two 6.7 mm screws.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
4. Stap 4
  Use your fingers to identify the location of the screw under the bottom label.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
5. Stap 5
  Use a Phillips #0 screwdriver to remove one 6.7 mm screw.
  
  Clear the label away from around the screw for easier removal.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
7. Stap 6
  Turn the mouse over so the bottom is facing down.
  
  Separate the top casing from the bottom base by pulling the top casing upwards.
  
  Separating the casing too quickly could damage the ribbon connector between the motherboard and the LED lights.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
8. Stap 7
  Disconnect the ribbon connector between the motherboard and the LED lights by pulling upward.
  
  Pulling too hard could damage the wire connections.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
1. Stap 8 Motherboard
  Disconnect the ribbon connector between the motherboard and the USB cable by pulling upward.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
2. Stap 9
  Use a Phillips #0 screwdriver to remove three 5.5 mm screws.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
3. Stap 10
  Use a Phillips #0 screwdriver to remove two 11.5 mm screws on the side buttons.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
4. Stap 11
  Use a Phillips #000 screwdriver to remove one 5.0 mm screw.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
5. Stap 12
  Disconnect the ribbon connector between the motherboard and the optical sensor.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
6. Stap 13
  Remove the motherboard by grasping the sides and gently pulling upward.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024
1. Stap 14 Scroll Wheel
  Remove the scroll wheel from the socket by pulling to the right.
  
  Pulling too hard could damage the scroll wheel connector.
  Vertaal
  
  Vraag FixBot
  
  Voeg opmerking toe
  
  1024

Conclusie

To reassemble your device, follow these instructions in reverse order.

Annuleren: ik heb deze handleiding niet afgemaakt.

11 andere personen hebben deze handleiding voltooid.

Auteur

met 1 andere bijdrager

Corrie Tung

Lid sinds: 03/24/17

711 Reputatie

2 handleidingen geschreven

+9 andere badges

Team

Baylor, Team S5-G2, Williams Spring 2017 Lid van Baylor, Team S5-G2, Williams Spring 2017

BU-WILLIAMS-S17S5G2

3 Leden

6 handleidingen geschreven

0Gids Commentaar

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 10

Afgelopen 30 dagen: 78

Altijd: 21,262