Ga door naar hoofdinhoud

Razer DeathAdder Chroma Motherboard Replacement Guide

Wat je nodig hebt

  1. Razer DeathAdder Chroma Motherboard Replacement Guide, Outer Casing: stap 1, afbeelding 1 van 1
    • Opening the mouse casing will void any warranty that exists for the mouse.

    • Turn the mouse over so the bottom is facing up.

  2. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 2, afbeelding 1 van 2 Razer DeathAdder Chroma Motherboard Replacement Guide: stap 2, afbeelding 2 van 2
    • Use the blunt end of the spudger to pry the adhesive rubber pads from the top left and right edges.

  3. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 3, afbeelding 1 van 2 Razer DeathAdder Chroma Motherboard Replacement Guide: stap 3, afbeelding 2 van 2
    • Use a Phillips #0 screwdriver to remove two 6.7 mm screws.

  4. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 4, afbeelding 1 van 1
    • Use your fingers to identify the location of the screw under the bottom label.

  5. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 5, afbeelding 1 van 1
    • Use a Phillips #0 screwdriver to remove one 6.7 mm screw.

    • Clear the label away from around the screw for easier removal.

  6. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 6, afbeelding 1 van 3 Razer DeathAdder Chroma Motherboard Replacement Guide: stap 6, afbeelding 2 van 3 Razer DeathAdder Chroma Motherboard Replacement Guide: stap 6, afbeelding 3 van 3
    • Turn the mouse over so the bottom is facing down.

    • Separate the top casing from the bottom base by pulling the top casing upwards.

    • Separating the casing too quickly could damage the ribbon connector between the motherboard and the LED lights.

  7. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 7, afbeelding 1 van 2 Razer DeathAdder Chroma Motherboard Replacement Guide: stap 7, afbeelding 2 van 2
    • Disconnect the ribbon connector between the motherboard and the LED lights by pulling upward.

    • Pulling too hard could damage the wire connections.

  8. Razer DeathAdder Chroma Motherboard Replacement Guide, Motherboard: stap 8, afbeelding 1 van 2 Razer DeathAdder Chroma Motherboard Replacement Guide, Motherboard: stap 8, afbeelding 2 van 2
    • Disconnect the ribbon connector between the motherboard and the USB cable by pulling upward.

  9. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 9, afbeelding 1 van 1
    • Use a Phillips #0 screwdriver to remove three 5.5 mm screws.

  10. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 10, afbeelding 1 van 2 Razer DeathAdder Chroma Motherboard Replacement Guide: stap 10, afbeelding 2 van 2
    • Use a Phillips #0 screwdriver to remove two 11.5 mm screws on the side buttons.

  11. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 11, afbeelding 1 van 1
    • Use a Phillips #000 screwdriver to remove one 5.0 mm screw.

  12. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 12, afbeelding 1 van 2 Razer DeathAdder Chroma Motherboard Replacement Guide: stap 12, afbeelding 2 van 2
    • Disconnect the ribbon connector between the motherboard and the optical sensor.

  13. Razer DeathAdder Chroma Motherboard Replacement Guide: stap 13, afbeelding 1 van 2 Razer DeathAdder Chroma Motherboard Replacement Guide: stap 13, afbeelding 2 van 2
    • Remove the motherboard by grasping the sides and gently pulling upward.

Conclusie

To reassemble your device, follow these instructions in reverse order.

5 andere personen hebben deze handleiding voltooid.

Nathan D. Kappler

Lid sinds: 03/27/17

343 Reputatie

2 handleidingen geschreven

Team

Baylor, Team S5-G2, Williams Spring 2017 Lid van Baylor, Team S5-G2, Williams Spring 2017

BU-WILLIAMS-S17S5G2

3 Leden

6 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 4

Afgelopen 7 dagen: 9

Afgelopen 30 dagen: 52

Altijd: 9,833