Repareer je spullen Gemeenschap Winkel

ORFELD EV-660-S222 Battery LED Board Replacement

Inleiding

If the LEDs for the battery life indicator on your ORFELD EV-660 have gone out, it can make it impossible to tell how much charge you have left and how long you can continue to vacuum for. Make sure to exercise caution when desoldering wires.

Wat je nodig hebt

  1. ORFELD EV-660-S222 Battery LED Board Replacement, Battery LED Board: stap 1, afbeelding 1 van 1

    • Separate the dust cover and the motor from the vacuum body by pressing the eject button.

    Vertaal

  2. ORFELD EV-660-S222 Battery LED Board Replacement: stap 2, afbeelding 1 van 2 ORFELD EV-660-S222 Battery LED Board Replacement: stap 2, afbeelding 2 van 2

    • Place the vacuum on its side, with the screws facing towards you.

    • Remove the 11.5 mm screws using a Phillips #1 screwdriver.

    Vertaal

  3. ORFELD EV-660-S222 Battery LED Board Replacement: stap 3, afbeelding 1 van 2 ORFELD EV-660-S222 Battery LED Board Replacement: stap 3, afbeelding 2 van 2
    Gereedschap gebruikt in deze stap:
    Tweezers
    $4.99
    Koop

    • Using tweezers, remove the sticker connecting the two halves.

    • Use the opening pick to gently separate the top half and the bottom half of the vacuum.

    • Press the blue buttons near the sides of the battery LEDs to remove the top half.

    Vertaal

  5. ORFELD EV-660-S222 Battery LED Board Replacement: stap 4, afbeelding 1 van 2 ORFELD EV-660-S222 Battery LED Board Replacement: stap 4, afbeelding 2 van 2

    • Slide out the charging port.

    Vertaal

  6. ORFELD EV-660-S222 Battery LED Board Replacement: stap 5, afbeelding 1 van 1

    • Lift the battery slightly to reveal the pin connectors.

    • Gently disconnect the six-pin connector that connects to the power button and battery LEDs.

    Vertaal

  7. ORFELD EV-660-S222 Battery LED Board Replacement: stap 6, afbeelding 1 van 3 ORFELD EV-660-S222 Battery LED Board Replacement: stap 6, afbeelding 2 van 3 ORFELD EV-660-S222 Battery LED Board Replacement: stap 6, afbeelding 3 van 3

    • Slide out the battery LEDs from the compartment.

    • Remove the plastic LED cover from the LED board.

    Vertaal

  8. ORFELD EV-660-S222 Battery LED Board Replacement: stap 7, afbeelding 1 van 1

    • Desolder the LED board from the wires.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 3 andere bijdragers

Sarthak Shrestha

Lid sinds: 09/12/23

441 Reputatie

3 handleidingen geschreven

Medailles: 6

+3 andere badges

Team

University of North Texas, Team 2-4, Harold Fall 2023 Lid van University of North Texas, Team 2-4, Harold Fall 2023

UNT-HAROLD-F23S2G4

4 Leden

5 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 1

Afgelopen 30 dagen: 20

Altijd: 194