Inleiding

This repair guide will give instructions on how to remove the Macintosh PowerBook 1400c RAM.

Onderdelen

Geen onderdelen nodig.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

Voeg opmerking toe

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

Voeg opmerking toe

Continue holding the latch then gently pull the battery out of the device.
  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

Voeg opmerking toe

Locate the CD-ROM Drive latch.
  • Locate the CD-ROM Drive latch.

Voeg opmerking toe

Slide the latch to the right to release the CD ROM drive.
  • Slide the latch to the right to release the CD ROM drive.

Voeg opmerking toe

Continue holding the latch then gently pull the CD-ROM Drive out of the device.
  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

Voeg opmerking toe

Locate the speaker cover.
  • Locate the speaker cover.

Voeg opmerking toe

Press firmly on each end of the speaker cover and slide it to the left.
  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - Antwoord

Gently lift the speaker cover to remove it.
  • Gently lift the speaker cover to remove it.

Voeg opmerking toe

Lift the keyboard up from the back using a spudger(wedge side).
  • Lift the keyboard up from the back using a spudger(wedge side).

Voeg opmerking toe

Gently lift the keyboard until only the ribbon cable remains attached.
  • Gently lift the keyboard until only the ribbon cable remains attached.

Voeg opmerking toe

Tilt the keyboard away from the screen.
  • Tilt the keyboard away from the screen.

Voeg opmerking toe

Locate the six screws that secure the heatsink.
  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - Antwoord

That isn't the HDD!

Dix Dox - Antwoord

Remove the six screws from the heatsink using the Philips #1 screwdriver.
  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

Voeg opmerking toe

Lift the heatsink from the side closest to the laptop screen.
  • Lift the heatsink from the side closest to the laptop screen.

Voeg opmerking toe

Remove the heatsink.
  • Remove the heatsink.

Voeg opmerking toe

Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.
  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

Voeg opmerking toe

Detach the ribbon cable.
  • Detach the ribbon cable.

Voeg opmerking toe

Remove the keyboard.
  • Remove the keyboard.

Voeg opmerking toe

Identify RAM Memory stick
  • Identify RAM Memory stick

  • These are the upgradeable RAM Memory sticks, they must be removed first

Voeg opmerking toe

Gently grasp the ram on the far end as shown in the picture and then pull up and away from the right side of the computer
  • Gently grasp the ram on the far end as shown in the picture and then pull up and away from the right side of the computer

Voeg opmerking toe

Remove the upgradeable RAM stick
  • Remove the upgradeable RAM stick

  • If the upgradeable RAM stick is all you are repairing you can end the guide here, however to remove the factory installed RAM please continue

Voeg opmerking toe

Gently grasp the factory installed RAM by grabbing each end as shown in the picture and pull the stick directly up
  • Gently grasp the factory installed RAM by grabbing each end as shown in the picture and pull the stick directly up

Voeg opmerking toe

Remove the factory installed RAM memory module
  • Remove the factory installed RAM memory module

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

4 andere personen hebben deze handleiding voltooid.

Kian Dinyari

Lid sinds: 07-04-11

125 reputatie

1 Handleiding geschreven

Team

Cal Poly, Team 10-39, Forte Spring 2011 Lid van Cal Poly, Team 10-39, Forte Spring 2011

CPSU-FORTE-S11S10G39

5 Leden

6 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 1

Afgelopen 7 Dagen: 5

Afgelopen 30 Dagen: 13

Altijd: 2,808