Ga door naar hoofdinhoud

Inleiding

Having wireless (Wi-Fi or Bluetooth) connectivity issues? Use this guide to replace the AirPort board.

  1. Remove the following pentalobe screws securing the lower case to the MacBook Pro:
    • Remove the following pentalobe screws securing the lower case to the MacBook Pro:

    • Eight 3.1 mm

    • Two 2.3 mm

  2. Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro. Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.
    • Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.

  3. The lower case has two plastic pegs (red) that fit into plastic clips in the upper case (orange). During reassembly, gently push down the center of the lower case to reattach the case to its two plastic clips. During reassembly, gently push down the center of the lower case to reattach the case to its two plastic clips.
    • The lower case has two plastic pegs (red) that fit into plastic clips in the upper case (orange).

    • During reassembly, gently push down the center of the lower case to reattach the case to its two plastic clips.

  4. MacBook-reparatiesets voor batterijen

    Vanaf $69.99

    Buy Now

    MacBook-reparatiesets voor batterijen

    Vanaf $69.99

    Buy Now
  5. Peel back the sticker covering the battery connector.
    • Peel back the sticker covering the battery connector.

  6. Gently lift each side of the battery connector to pry the connector out of its socket on the logic board. Bend the connector back toward the battery, ensuring that the battery connector doesn't accidentally make contact with the logic board. Bend the connector back toward the battery, ensuring that the battery connector doesn't accidentally make contact with the logic board.
    • Gently lift each side of the battery connector to pry the connector out of its socket on the logic board.

    • Bend the connector back toward the battery, ensuring that the battery connector doesn't accidentally make contact with the logic board.

  7. Disconnect the three airport Antenna cable connectors from their sockets on the AirPort board and bend them up and out of the way. Be careful to pry only against each connector, and not its cable or socket. Be careful to pry only against each connector, and not its cable or socket.
    • Disconnect the three airport Antenna cable connectors from their sockets on the AirPort board and bend them up and out of the way.

    • Be careful to pry only against each connector, and not its cable or socket.

  8. Remove the single 2.9 mm T5 Torx screw securing the AirPort board.
    • Remove the single 2.9 mm T5 Torx screw securing the AirPort board.

  9. Lift the end of the AirPort board up enough to pass over the heat sink directly behind it. Do not lift the AirPort board too high, or you could damage the contacts or socket. Pull the AirPort board straight out of its socket on the logic board.
    • Lift the end of the AirPort board up enough to pass over the heat sink directly behind it.

    • Do not lift the AirPort board too high, or you could damage the contacts or socket.

    • Pull the AirPort board straight out of its socket on the logic board.

    • There is a slightly adhesive thermal pad beneath the AirPort board. Be sure to reapply this when reinstalling the board, or transfer it to your replacement board.

Conclusie

To reassemble your device, follow these instructions in reverse order.

5 andere personen hebben deze handleiding voltooid.

Andrew Optimus Goldheart

Lid sinds: 17-10-09

417.309 Reputatie

411 handleidingen geschreven

Team

iFixit Lid van iFixit

Community

98 Leden

8.935 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 7

Afgelopen 7 Dagen: 96

Afgelopen 30 Dagen: 394

Altijd: 10,810