Skip to main content

Inleiding

The JBL Charge 3 has two front speaker that can be replaced individually or together. If your speakers are blown out replace them with this guide.

  1. Turn your speaker upside down and insert the plastic opening tool vertically into the slit in the front cover. Slowly pull the plastic opening tool outward to remove the four clips holding the covering in place. Repeat this process for all four edges of the front cover.
    • Turn your speaker upside down and insert the plastic opening tool vertically into the slit in the front cover.

    • Slowly pull the plastic opening tool outward to remove the four clips holding the covering in place.

    • Repeat this process for all four edges of the front cover.

  2. Pull apart your cover gently from both sides and remove it from the speaker housing.
    • Pull apart your cover gently from both sides and remove it from the speaker housing.

    • The inside of the front cover has holes that must match with their corresponding pins on the speaker housing for proper reassembly.

    • Removing the Front Cover does not affect the waterproof seals of the device. However, removing any further disassembly of your speaker will require removing waterproof seals and gaskets. Your device may no longer be waterproof after these have been altered.

  3. Remove the eight 10mm Phillips #1 screws from around the two front speakers. Remove the eight 10mm Phillips #1 screws from around the two front speakers.
    • Remove the eight 10mm Phillips #1 screws from around the two front speakers.

  4. MacBook-reparatiesets voor batterijen

    Vanaf $69.99

    Buy Now

    MacBook-reparatiesets voor batterijen

    Vanaf $69.99

    Buy Now
  5. Pull gently on one of the speakers so it is outside of the housing. Be careful as it is still attached with the wires to the motherboard.
    • Pull gently on one of the speakers so it is outside of the housing. Be careful as it is still attached with the wires to the motherboard.

  6. Press the small metal tab on the speaker connector with a Phillips #000 screwdriver and gently pull the connector apart. Press the small metal tab on the speaker connector with a Phillips #000 screwdriver and gently pull the connector apart. Press the small metal tab on the speaker connector with a Phillips #000 screwdriver and gently pull the connector apart.
    • Press the small metal tab on the speaker connector with a Phillips #000 screwdriver and gently pull the connector apart.

  7. Repeat the previous step for the second connector.
    • Repeat the previous step for the second connector.

  8. Grab the bundled cable connector that joins the speakers to the motherboard with tweezers. Gently pull the connector free. Grab the bundled cable connector that joins the speakers to the motherboard with tweezers. Gently pull the connector free.
    • Grab the bundled cable connector that joins the speakers to the motherboard with tweezers. Gently pull the connector free.

  9. Now that the second speaker is disconnected from the motherboard, pull the speaker and wires out of the housing.
    • Now that the second speaker is disconnected from the motherboard, pull the speaker and wires out of the housing.

Conclusie

To reassemble your device, follow these instructions in reverse order.

6 andere personen hebben deze handleiding voltooid.

Aidan Hays

Lid sinds: 08-10-18

576 Reputatie

2 handleidingen geschreven

Team

Cal Poly, Team S13-G1, White Fall 2018 Lid van Cal Poly, Team S13-G1, White Fall 2018

CPSU-WHITE-F18S13G1

4 Leden

14 handleidingen geschreven

Where I can buy the same jbl speaker ?

Ekinox - Antwoord

Where can buy the small speakers? Helpp

Luis Cilia - Antwoord

I have to pull out the motherboard to get those speakers out.

Tr0ll05aur0s 3z - Antwoord

where can i buy the replacement speakers?

Yhamani Pangarungan - Antwoord

Mine did not have the little clips in step 5. It was just soldered on. I ended up removing it from the other end. At the little white clip that goes in the motherboard (shown in step &) I was able to remove the pin. by pressing down on the top where you can see the silver.

Mike - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 59

Afgelopen 7 Dagen: 295

Afgelopen 30 Dagen: 1,381

Altijd: 6,630