Ga door naar hoofdinhoud

Repareer je spullen

Recht op reparatie

Winkel

Inleiding

Follow this guide to replace the charging assembly on a Sony Dualshock 4 CHU-ZCT2U PlayStation controller.

  1. Use a Phillips screwdriver to remove the four 6.4 mm-long screws from the rear panel. Use a Phillips screwdriver to remove the four 6.4 mm-long screws from the rear panel.
    • Use a Phillips screwdriver to remove the four 6.4 mm-long screws from the rear panel.

  2. Insert an opening tool into the crease where the front and rear panel meet, starting from the outside edge of either handle. Gently pry the rear panel off of the front panel until they become partially separated.
    • Insert an opening tool into the crease where the front and rear panel meet, starting from the outside edge of either handle.

    • Gently pry the rear panel off of the front panel until they become partially separated.

  3. Use the opening tool to separate the panels by releasing the plastic clips around the perimeter of the controller. Use the opening tool to separate the panels by releasing the plastic clips around the perimeter of the controller. Use the opening tool to separate the panels by releasing the plastic clips around the perimeter of the controller.
    • Use the opening tool to separate the panels by releasing the plastic clips around the perimeter of the controller.

  4. Lift the rear panel directly away from the controller. Do not completely remove the rear panel. It is still attached to the controller by a ribbon cable.
    • Lift the rear panel directly away from the controller.

    • Do not completely remove the rear panel. It is still attached to the controller by a ribbon cable.

  5. Use your fingers to gently pull the ribbon cable straight out of its connector on the motherboard. Since this cable's pull tab is too small to grab with fingers or tweezers, grab the cable itself. Otherwise utilize pull tabs whenever possible.
    • Use your fingers to gently pull the ribbon cable straight out of its connector on the motherboard.

    • Since this cable's pull tab is too small to grab with fingers or tweezers, grab the cable itself. Otherwise utilize pull tabs whenever possible.

    • During reassembly, grab the ribbon cable by the blue tab and gently press the cable straight into the connector. Push the blue tab rather than the ribbon cable itself.

  6. Use an opening tool or spudger to separate the white plastic bar from the rear panel. Use an opening tool or spudger to separate the white plastic bar from the rear panel. Use an opening tool or spudger to separate the white plastic bar from the rear panel.
    • Use an opening tool or spudger to separate the white plastic bar from the rear panel.

  7. Remove the white plastic bar. Remove the white plastic bar.
    • Remove the white plastic bar.

  8. Lift the light guide away from the rear panel to remove it. During reassembly, align the light guide with the rear panel using the notch near the bottom left. During reassembly, align the light guide with the rear panel using the notch near the bottom left.
    • Lift the light guide away from the rear panel to remove it.

    • During reassembly, align the light guide with the rear panel using the notch near the bottom left.

  9. Use your fingers to press the translucent plastic piece down through the top of the controller. Remove the translucent plastic piece. Remove the translucent plastic piece.
    • Use your fingers to press the translucent plastic piece down through the top of the controller.

    • Remove the translucent plastic piece.

  10. Use a Phillips screwdriver to remove the 4.4 mm-long screw from the charging assembly. Use a Phillips screwdriver to remove the 4.4 mm-long screw from the charging assembly.
    • Use a Phillips screwdriver to remove the 4.4 mm-long screw from the charging assembly.

  11. Use the pointed end of a spudger to lift the charging assembly away from the rear panel. Use the pointed end of a spudger to lift the charging assembly away from the rear panel.
    • Use the pointed end of a spudger to lift the charging assembly away from the rear panel.

  12. Use your fingers or a pair of tweezers to remove the charging assembly from the rear panel. Use your fingers or a pair of tweezers to remove the charging assembly from the rear panel.
    • Use your fingers or a pair of tweezers to remove the charging assembly from the rear panel.

Conclusie

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Sam Omiotek

Lid sinds: 25-02-19

12.911 Reputatie

94 handleidingen geschreven

Team

iFixit Lid van iFixit

Community

135 Leden

13.965 handleidingen geschreven

Question:

I have a ps4 controller model CUH-ZCT2U. My charging board model is jds 050.

Can I buy the jds 055 charging board and put that in? Is the jds 050 and the jds 055 charging board interchangeable?

I can't seem to find the jds 050 charging boards anywhere. Only the jds 055. Any help would be very much appreciated. Thanks.

Treadway Customs - Antwoord

I have not tested the JDS-055 and JDS-050 in a ZCT2U so I cannot guarantee it will work. However, visually they appear to be the same part made by a different manufacturer. I suspect that it will work, but understand that it’s a gamble and make sure the store you buy from has a good return policy like iFixit. If you can wait, add yourself to the notify list for the JDS-050 and order once they become available again.

Sam Omiotek -

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 3

Afgelopen 7 dagen: 45

Afgelopen 30 dagen: 197

Altijd: 942