Menu

Jouw instellingen

Mijn werkbank

Krijg snel toegang tot handleidingen, onderdelen en antwoorden voor jouw apparaten
Winkelwagen

Het lijkt erop dat je mandje leeg is

Doorblader onze winkel

Canon Selphy CP720 Screen Replacement

Geschreven door: Peter Ely (en 3 andere bijdragers)
  • Reacties: 0
  • Favorieten: 0

Moeilijkheid

Gemiddeld

Stappen

8

Tijd vereist

10 - 15 minuten

Secties

1

Markeringen

0

Inleiding

This guide will show you how to properly remove and replace the screen on the Canon Selphy CP720 in the event that it is damaged or does not work.

Gereedschap

Koop deze gereedschappen

Onderdelen

Geen onderdelen opgegeven.

  1. Remove the three 6mm Phillips #1 screws.

    • Remove the three 6mm Phillips #1 screws.

    Bewerken

  2. Remove the four 8mm Phillips #1 screws, located in each corner of the device. Remove the four 8mm Phillips #1 screws, located in each corner of the device.

    • Remove the four 8mm Phillips #1 screws, located in each corner of the device.

    Bewerken

  3. Grasp one half of the device's shell in each hand, and pull them apart. They are connected, so don't separate them completely.

    • Grasp one half of the device's shell in each hand, and pull them apart. They are connected, so don't separate them completely.

    Bewerken

  4. MacBook-reparatiesets voor batterijen

    Vanaf $69.99

    Buy Now

    MacBook-reparatiesets voor batterijen

    Vanaf $69.99

    Buy Now

  5. Lift the side panel off to expose the inside of the printer. Lift the side panel off to expose the inside of the printer.

    • Lift the side panel off to expose the inside of the printer.

    Bewerken

  6. Remove the four 8mm Phillips #00 screws that hold the upper circuit board to the shell.

    • Remove the four 8mm Phillips #00 screws that hold the upper circuit board to the shell.

    Bewerken

  7. Remove two 8mm Phillips #00 screws from the yellow board.

    • Remove two 8mm Phillips #00 screws from the yellow board.

    Bewerken

  8. Remove the two 8mm Phillips #00 screws from the screen.

    • Remove the two 8mm Phillips #00 screws from the screen.

    • Lift off the circuit board, yellow board, and screen.

    Bewerken

  9. To separate the screen from the circuit board, grasp the data ribbon cable near the base of the black connector on the circuit board and pull parallel to the surface of the board, toward the screen. To separate the screen from the circuit board, grasp the data ribbon cable near the base of the black connector on the circuit board and pull parallel to the surface of the board, toward the screen. To separate the screen from the circuit board, grasp the data ribbon cable near the base of the black connector on the circuit board and pull parallel to the surface of the board, toward the screen.

    • To separate the screen from the circuit board, grasp the data ribbon cable near the base of the black connector on the circuit board and pull parallel to the surface of the board, toward the screen.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 3 andere bijdragers

Peter Ely

Lid sinds: 26-09-18

785 Reputatie

5 handleidingen geschreven

Badges: 4

+1 extra badge

Team

Eastern Washington University, Team S1-G1, Carnegie Fall 2018 Lid van Eastern Washington University, Team S1-G1, Carnegie Fall 2018

EWU-CARNEGIE-F18S1G1

4 Leden

5 handleidingen geschreven

0 Opmerkingen

Een opmerking toevoegen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 4

Altijd: 45