Ga door naar hoofdinhoud

Inleiding

Use this guide to remove the front speaker panel in your device. You’ll need to know how to solder to fully replace the speaker panel in your Braven BRV-X. The How to Solder and Desolder Connections guide may help you with this guide.

Onderdelen

Geen onderdelen opgegeven.

  1. Braven BRV-X Front Speaker Panel Replacement, Front Speaker Panel: stap 1, afbeelding 1 van 1
    • Remove four 1.1 cm outer screws in the outer shell using the Phillips #00 screwdriver.

  2. Braven BRV-X Front Speaker Panel Replacement: stap 2, afbeelding 1 van 1
    • Remove four 1.3 cm inner screws in the outer shell using the 1.5mm Hex screwdriver.

  3. Braven BRV-X Front Speaker Panel Replacement: stap 3, afbeelding 1 van 1
    • Gently remove the outer shell.

  4. Braven BRV-X Front Speaker Panel Replacement: stap 4, afbeelding 1 van 2 Braven BRV-X Front Speaker Panel Replacement: stap 4, afbeelding 2 van 2
    • Cut adhesive tape on both sides.

  5. Braven BRV-X Front Speaker Panel Replacement: stap 5, afbeelding 1 van 2 Braven BRV-X Front Speaker Panel Replacement: stap 5, afbeelding 2 van 2
    • Remove eighteen 0.9cm screws in the inner shell using the Phillips #00 screwdriver.

  6. Braven BRV-X Front Speaker Panel Replacement: stap 6, afbeelding 1 van 3 Braven BRV-X Front Speaker Panel Replacement: stap 6, afbeelding 2 van 3 Braven BRV-X Front Speaker Panel Replacement: stap 6, afbeelding 3 van 3
    • Pry open the glued inner shell using a spudger around all sides of the shell.

    • Don't use too much pressure as that could cause damage to the plastic.

  7. Braven BRV-X Front Speaker Panel Replacement: stap 7, afbeelding 1 van 2 Braven BRV-X Front Speaker Panel Replacement: stap 7, afbeelding 2 van 2
    • Remove ten 0.7 cm screws in the front plate using the 1.5 mm Hex screwdriver.

  8. Braven BRV-X Front Speaker Panel Replacement: stap 8, afbeelding 1 van 2 Braven BRV-X Front Speaker Panel Replacement: stap 8, afbeelding 2 van 2
    • Use a spudger to open the front speaker plate.

  9. Braven BRV-X Front Speaker Panel Replacement: stap 9, afbeelding 1 van 1
    • Remove three 1.0 cm screws from the battery unit.

    • It is recommended (but not required) to remove the battery.

  10. Braven BRV-X Front Speaker Panel Replacement: stap 10, afbeelding 1 van 2 Braven BRV-X Front Speaker Panel Replacement: stap 10, afbeelding 2 van 2
    • Disconnect the ribbon cable attached the main board.

  11. Braven BRV-X Front Speaker Panel Replacement: stap 11, afbeelding 1 van 3 Braven BRV-X Front Speaker Panel Replacement: stap 11, afbeelding 2 van 3 Braven BRV-X Front Speaker Panel Replacement: stap 11, afbeelding 3 van 3
    • Pry open the second plate holding in the speaker using a spudger around all sides.

    • It is recommended to use a spudger to remove the heavily glued areas between the plates before prying.

    • Don't use too much pressure as that could cause damage to the plastic.

  12. Braven BRV-X Front Speaker Panel Replacement: stap 12, afbeelding 1 van 3 Braven BRV-X Front Speaker Panel Replacement: stap 12, afbeelding 2 van 3 Braven BRV-X Front Speaker Panel Replacement: stap 12, afbeelding 3 van 3
    • Cut the 20 gauge wires attached to the front IR sensor and two speaker wires.

    • Leave enough length on the wire to work with it afterwards.

    • Cut the 22 gauge wire attached in the corner.

    • Solder the new speaker plate during reassembly.

    • To properly solder and desolder connections, visit the How to Solder and Desolder Connections guide.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Trey Peterson

Lid sinds: 01-04-19

301 Reputatie

2 handleidingen geschreven

Team

IUPUI, Team S1-G5, Harley Spring 2019 Lid van IUPUI, Team S1-G5, Harley Spring 2019

IUPUI-HARLEY-S19S1G5

3 Leden

2 handleidingen geschreven

0 Opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 4

Afgelopen 30 dagen: 5

Altijd: 179