Ga door naar hoofdinhoud

Back Case

Wat je nodig hebt

  1. Back Case, Battery: stap 1, afbeelding 1 van 1
    • Orient camera to look directly at battery compartment side as shown.

  2. Back Case: stap 2, afbeelding 1 van 3 Back Case: stap 2, afbeelding 2 van 3 Back Case: stap 2, afbeelding 3 van 3
    • Locate the two latches on the battery compartment.

    • First, move the "lock" switch left to reveal red indicator.

    • Next, move the "cover latch" switch downward to reveal red indicator.

    • You have to move the switches in that order for the compartment to unlatch.

  3. Back Case: stap 3, afbeelding 1 van 2 Back Case: stap 3, afbeelding 2 van 2
    • Allow the battery compartment latch to completely open.

    • Insert battery with the writing face up.

    • The bigger slot is for the battery. The smaller slot is for the memory card.

    • Battery not shown.

  4. Back Case, Back Case: stap 4, afbeelding 1 van 1
    • Orient the camera so you are looking at the bottom.

    • Remove the three 3.85mm Phillips #00 screws from the bottom of the camera.

  5. Back Case: stap 5, afbeelding 1 van 1
    • Orient the camera so you are looking at the side plate.

    • Remove the two 3.15mm Phillips #00 screws from the side plate of the camera.

  6. Back Case: stap 6, afbeelding 1 van 2 Back Case: stap 6, afbeelding 2 van 2
    • Orient the camera so you are looking at the front plate.

    • Remove the two 3.8mm with the Phillips H1.5 from the front plate.

    • Remove the "Olympus" plate.

  7. Back Case: stap 7, afbeelding 1 van 1
    • Remove face plate.

  8. Back Case: stap 8, afbeelding 1 van 3 Back Case: stap 8, afbeelding 2 van 3 Back Case: stap 8, afbeelding 3 van 3
    • Locate three small black screws inside of the battery compartment.

    • Remove the 3.85mm Phillips #00 screw on the far left side.

    • Remove the two 5mm Phillips #00 screws on the right side

  9. Back Case: stap 9, afbeelding 1 van 3 Back Case: stap 9, afbeelding 2 van 3 Back Case: stap 9, afbeelding 3 van 3
    • Orient the camera to be look at the top.

    • Remove the 5.4mm Phillips #00 screw on the top left side.

    • Remove the 7.4mm Phillips #00 screw next to the "ON/OFF" label.

    • Pry off top button plate with black nylon spudger.

  10. Back Case: stap 10, afbeelding 1 van 2 Back Case: stap 10, afbeelding 2 van 2
    • Rotate to bottom of camera and locate bottom latch.

    • Wedge black nylon spudger in between bottom latch and camera base to release LCD Screen from camera.

    • Push firmly apart.

    • Some buttons might fall out.

  11. Back Case: stap 11, afbeelding 1 van 3 Back Case: stap 11, afbeelding 2 van 3 Back Case: stap 11, afbeelding 3 van 3
    • Orient the camera to the LCD screen side that is now wedged open.

    • Locate the white ribbon cable and pull out from motherboard.

    • Locate the brown ribbon cable and pull out from motherboard.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Larissa Knight

Lid sinds: 03/21/16

549 Reputatie

5 handleidingen geschreven

Team

Clemson, Team 7-2, Benson Spring 2016 Lid van Clemson, Team 7-2, Benson Spring 2016

CLEM-BENSON-S16S7G2

4 Leden

16 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 3

Altijd: 681