Complete Part List With Tips
BULLETIN NO. 54-26-2480
SERVICE PARTS LIST
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M12™ Brushless 1/4" Hex Impact Driver
CATALOG NO.
2453-20
REVISED BULLETIN
DATE May 2019
WIRING INSTRUCTION
SEE PAGE 3
STARTING SERIAL NO.
E51A
3
FIG.
| FIG. PART NO. | DESCRIPTION OF PART | NO. REQ. |
|---|---|---|
| 1 31-12-0575 | Rubber Cap | (1) |
| 2 45-22-2653 | Sleeve | (1) |
| 3 34-60-0725 | Retaining Ring | (1) |
| 4 45-88-1881 | Washer | (1) |
| 5 40-50-1470 | Spring | (1) |
| 6 --- | Anvil Bushing (Not Shown) | (1) |
| 9 45-88-2135 | Plastic Washer | (1) |
| 10 02-02-0170 | 3.5mm Steel Ball | (1) |
| 11a 42-06-0720 | 1/4" Hex Anvil | (1) |
| 12 02-02-1300 | 5mm Steel Ball | (1) |
| 19 02-02-0180 | 4.7mm Steel Ball | (2) |
| 22 --- | Ball Bearing | (1) |
| 23 --- | Gearcase End Cap | (1) |
| 24 --- | Ring Gear | (1) |
| 25 44-66-1065 | Gearcase End Cap Assembly | (1) |
| 27 --- | Stator Assembly | (1) |
| 28 45-30-0300 | Rubber Slug | (4) |
| 34 --- | PCBA | (1) |
| 35 --- | On-Off Switch | (1) |
| 36 --- | Terminal Block Assembly | (1) |
| 37 45-24-0810 | Fwd/Rev Shuttle | (1) |
| 38 40-50-1135 | Spring | (1) |
| 42 42-70-0055 | Housing Connection Clip | (1) |
| 43 --- | Left Handle Halve with Fuel Gauge | (1) |
| 44 42-70-0580 | Belt Clip | (1) |
| 45 --- | Belt Hook Screw | (1) |
| 46 06-82-1090 | M3 x 7mm Pan Hd. Plastite Screw | (2) |
Table Caption: This table lists parts for a device, including their part numbers, descriptions, and quantities required. It details components ranging from small rubber caps and springs to larger assemblies like the stator and gearcase end cap.
Table Caption: This table lists parts for a tool, including their figure number, part number, description, and quantity required, along with lubrication instructions for specific components.
Early M12™ Handle Sets utilize Housing Connection Clip No. 42-70-0055. Install this clip design by aligning the side rails of the clip with the two slots in the handle set. Gently push into place with the aid of a small flat blade screwdriver or a similar instrument. Be sure that the clip is properly seated in both slots and that the clip is flush to sub-flush to the end of the handle set. To remove the clip, use the same small flat blade screwdriver or a similar instrument and push the clip out of the handle set. If the clip is loose or will not stay in place, a needle nose pliers can be used to gently bend/pinch the side rails of the clip. If the clip is damaged do not use, replace with a new 42-70-0055 housing clip.
Updated M12™ Handle Sets utilize Housing Connection Clips No. 42-70-0055 and 42-700058. (The 42-70-0058 is a preferred upgrade). Install this clip design by aligning the side rails of the clip with the two slots in the handle set. Gently push into place with the aid of a small flat blade screwdriver or a similar instrument. Be sure that the clip is properly seated in both slots and that the tab of the clip snaps down in the round dimpled cavity of the handle set. Be sure that the clip is flush to sub-flush to the end of the handle set. To remove the clip, use the same small flat blade screwdriver or a similar instrument and lift up on the clip tab while pushing the clip out of
Meld je gratis aan bij iFixit om het volledige document te lezen (3 pagina's)
We vragen je om een gratis account aan te maken, zodat we bots kunnen blokkeren en iFixit voor mensen kunnen houden.
