Released September 25, 2015. Model A1688/A1633. Repair of this device is similar to previous generations, requiring screwdrivers and prying tools. Available as GSM or CDMA / 16, 64, or 128 GB / Silver, Gold, Space Gray, or Rose Gold options.

1654 Vragen Bekijk alle

iPhone stuck in Boot Loop only when plugged in to power outlet.

Hello everyone,

My iPhone 6s fell this past weekend and since then has been stuck in a boot loop (apple logo appears and disappears) whenever it is plugged in to an outlet.

Ultimately I'd like to pull the data out of my phone via iTunes backup, but the problem I'm facing is that my iPhone does not seem to boot up when plugged in to my PC's usb port.

Anyone have an idea how I can enact atleast a bootloop on a PC or get my turned off iPhone recognized in iTunes?

I tried finding answers via search, but nothing seems to touch on the issue of my iPhone not booting when plugged in to a usb port on the PC.

Thank you.

Beantwoord! View the answer Dit probleem heb ik ook

Is dit een goede vraag?

Score 1
Een opmerking toevoegen
Verspreid de kerstsfeer
Krijg 12€ korting op je aankoop van 50€ of meer met de code FIXMAS12
Verspreid de kerstsfeer
Krijg 12€ korting op je aankoop van 50€ of meer met de code FIXMAS12

4 Antwoorden

Gekozen oplossing

Here are some things to try when you are faced with a boot-looping phone.

  • Try a hard reset (Home & Power button for 10 secs)
  • Use a genuine Apple Lightning connector
  • Use a genuine Apple charging brick and let it charge overnight
  • Try to connect it to different computers (mac/pc if possible) with an updated iTunes
  • Put the phone in recovery mode (search DFU Mode). Careful, this can reset your data
  • Use 3uTools for putting it in and out of Recovery Mode
  • Use 3uTools to flash the firmware (you can't downgrade)
  • Check the condition of all the flexes (with magnification)
  • Disconnect the Front Camera Ribbon from the logic board and reboot your phone
  • Disconnect the screen assembly completely and see if iTunes will recognize the phone.

Otherwise, you may have a logic board issue. If you are uncomfortable doing these steps, consider finding a repair shop to do the troubleshooting. A shop that also does micro-soldering can go deeper if the problem is not modular in nature.

Was dit antwoord nuttig?

Score 2
Een opmerking toevoegen

Hi everyone and thank you for the responses.

It turned out my phone had simply died and I ended up having to go with the hard reset in order for my phone to work again.

Was dit antwoord nuttig?

Score 0

Commentaar:

Can you explain how did the hard reset work for you? ive been stuck on this one

door

Een opmerking toevoegen

Try force restart, press and hold power button and Home button at the same time about 10s until you see an Apple Logo then release it.

Was dit antwoord nuttig?

Score 0
Een opmerking toevoegen

I tried using 3U tool to restore my 6s from Recovery Mode. Screen with apple Logo Started flashing (@ 2-3sec per flash). On & OFF .. it is just going on. Nothing is working.

Status is also started showing “Not Connected”

When i remove the Lightening Cable from the phone, it just shuts Off Instantly.

Any Advice / suggestions ..

Regards

Was dit antwoord nuttig?

Score 0

Commentaar:

DFU recovery!!! search up videos on youtube

door

you may have to attempt it a few times. Ive seen reviews of people needing it upwards up 3 times before it works. It will erase ALL data, just make sure its backed up

door

Een opmerking toevoegen

Voeg je antwoord toe

CGSK zal eeuwig dankbaar zijn.
Weergavestatistieken:

Afgelopen 24 Uren: 8

Afgelopen 7 Dagen: 97

Afgelopen 30 Dagen: 358

Altijd: 4,830