Deze gebruiker heeft hun profiel nog niet ingevuld.
Vragen
Hello all I have recently replaced the digitizer on a Nokia Lumia 820 (aftermarket part not original). All is ok except...
Meer informatieHello Fellow Techncians I was wondering if you could help me I have replaced a battery in a ipod 4th gen with Click wheel,...
Meer informatieHi Wondering if you clever people could assist I have a iphone 5c that has no sound from the ear speaker, i have replaced...
Meer informatieHello All Wondering if you could assist with a strange fault. I have a iphone 5s which I have now replaced TWO original...
Meer informatieHi Please can anybody point me in the direction of the microphone used when recording a audio clip on the galaxy S5,...
Meer informatieHello All I was wondering if you could asssit, i need to change the volume flex on a ipod touch 5th gen, and i cant seem...
Meer informatieHello All Wondering if you could help me My Son decided to vomit into my phone and into my pocket today (i love him)...
Meer informatieHi Please can somebody tell me where the secondary mic is located on the 4S please note i say 4S not 4 Regards Ali
Meer informatieHi I have a Ihpone 4S which works fine, the only problem is when i record video the sound on the feedback is just very...
Meer informatieHi Wondering if someone can help I have a iphone 4 to repair which has been dropped in the toilet and then flushed I...
Meer informatiePagina 1 van 2
Antwoorden
Hi Thank you for the answer however to ensure others are not confused I think youll find that cable in the picuture is for the power and volume button, i located the digitizer cable its on the bottom of the screen Regards Ali
Meer informatieBlack piece phot can be found here little ribbon guard mainboard
Meer informatieHi when replacing the screen you dont need to bend it as much as the exisitng one, you only need to push down on the little metal tab enough for the motherboard to sit in you will not get any replacement digitizers with the cables bent for you Regards Ali
Meer informatieHi Please can you recheck the connectors of the LCD/Digtizer to ensure they are seated properly if not then the usual problem is that when feeding the replacement digitizer cables through the midframe if you dont pull them through completely sometimes you can squash and crimp the cable resulting inwhat you are saying Regards Ali
Meer informatiehi it may be that the battery needs calibrating, this means that the actual battery power and what the software think are out of synch please try the following 1) Allow the battery to completely Die 2) Charge it fully 3) Allow it to completely die 4) Charge it fully This should recalibrate the battery
Meer informatieHi The backplate at the top is the WiFi shield and in my experience if screws are missing from there MOST of the time WiFi will not work, you will need to ensure all screws for that black plate are in place and screwed into the motherboard Regards Ali
Meer informatieThe issue you are having is due to a motherboard issue a fix can be found here http://www.youtube.com/watch?v=0jhWxYTVx... Regards Ali
Meer informatieHi The issue is maybe 2 things The mic connector at the bottom (the balc with the antenna cable) you will notice has 4 metal prongs, these need to be tucked in underneath the metal midframe, if they sit on top you may get the issues you are describing if these 4 prongs are correct then the fault is likely to be with the cable that feeds these things not being on properley, this is the cable that has the little black metal plate with the 2 screws. Ensure this cable is down properly i provide a link to a video that may help http://www.youtube.com/watch?v=QRSvswPGl... At about 2:43 you will see the metal plate and cable i am referring to Regards Ali
Meer informatieHi It looks like you may have damaged the mic at the bottom. you will most likely need to get this replaced Replacing the mic can be found here and if your confident moderate to repair http://www.youtube.com/watch?v=xaA5Kh0Hp... Please note all repairs are at your own risk Regards
Meer informatieHi As mentioned above if you are using a metal spudger to get the old screen off, you may have gone through the charging dock cable, however before removing this new digitizer, please ensure you try another charger in case the current one is faulty Regards Ali
Meer informatiePagina 1 van 2
Ali
@ali50509
287
Reputatie
16
Oplossingen
0
Handleidingen
Lid sinds 01/15/13