Gereedschappen die in deze demontage worden gebruikt

Inleiding

We disassembled this iPod on September 7, 2007.

Deze demontage is geen reparatiehandleiding. Om je iPod Nano 3rd Generation te repareren, gebruik onze reparatiehandleidingen.

There it is, in the same style box as the last Nano, but quite a bit shorter and wider.
  • There it is, in the same style box as the last Nano, but quite a bit shorter and wider.

Voeg opmerking toe

Here's what you'll find in the box:
  • Here's what you'll find in the box:

    • A manual (even smaller than the iPod).

    • The usual, much-maligned headphones.

    • A USB to iPod cable.

    • A dock insert.

    • A brand new iPod.

Voeg opmerking toe

  • The growing iPod Nano family.

  • Although the new Nano is shorter and wider than its older siblings, it has approximately the same area (36 square centimeters).

Voeg opmerking toe

  • Apple appears to be going in circles. Anodized aluminum, shiny, anodized, shiny...

  • But of course, it's what's inside that counts.

Voeg opmerking toe

  • And here's our first look inside this newest Nano.

  • The case has eight locking tabs:

    • Three on the left, evenly spaced.

    • Three on top.

    • Two on the right, near the bottom, to make room for the display circuitry at the upper right.

How do i get the back panel off? it wont seem to slide up or anything

andy - Antwoord

  • We've removed six Phillips screws fixing the logic board to the casing.

  • We can now lift the logic board up, but it's still tethered by the visible click wheel cable and the hidden display cable.

Voeg opmerking toe

  • We've disconnected the click wheel cable and flipped the board over to disconnect the display cable.

Voeg opmerking toe

  • Now we use a spudger to pry up the display, which is held along the case's edge by an adhesive strip.

  • The first generation Nano's display was attached in exactly the same way. If you're not careful when prying it up, you may crack it.

Voeg opmerking toe

  • We're noticing a strong trend as we take apart this iPod: adhesive.

  • The click wheel is held in place by nothing but a very strong adhesive, which is going to make replacing it difficult. You'll have to get it to stay in place as well as Apple has (i.e. very well).

Voeg opmerking toe

  • Here the battery is out of its metal housing, which is attached to the logic board by, that's right, adhesive.

  • The battery is attached to the logic board by three through-hole solder points, as in the second generation Nano (sorry, no easy replacements).

Samsung????!!

Toni Palmer - Antwoord

Yes, that's how alot of flash based devices run Samsung chips

fraijoni - Antwoord

Of course!!!

Toni Palmer -

  • And here's everything together again, but apart.

Voeg opmerking toe

  • A close-up of the logic board's top, which sports an eight gigabyte Samsung flash memory chip and headphone jack.

  • The headphone jack is soldered to the logic board, as in the first generation Nano, but not in the second.

Voeg opmerking toe

  • A close-up of the logic board's bottom.

The top middle chip (below the dock connector is 256 megs of sdram

Lucas Hoekstra (Lucas9810) - Antwoord

Is it possible to replace the power port?

Brionced Loo - Antwoord

  • And it still works! Now, having satisfied our curiosity, we can put some music on it.

Voeg opmerking toe

I have done the same thing to my ipod nano 3g as shown on these pics u posted.I've changed my ipod housing and now it looks as new as ever..thanks! i luv ya!

grimjaww - Antwoord

Which two out of three terminals are positive and negative.

Ravi - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 33

Afgelopen 30 Dagen: 174

Altijd: 181,541