Ga door naar hoofdinhoud

Video overzicht

Deze demontage is geen reparatiehandleiding. Om je PlayStation 2 te repareren, gebruik onze reparatiehandleidingen.

  1. Deze stap is niet vertaald. Help het te vertalen

    Here we have the system console fully assembled. The USB Ports. The S400 ports
    • Here we have the system console fully assembled.

    • The USB Ports.

    • The S400 ports

    • The Optical Drive

    • The reset button

    • The eject button

  2. Deze stap is niet vertaald. Help het te vertalen

    These are the only tools that we will need. 4 screwdrivers and a tweezer. In the next photo we can see the console, the joystick, the wires and a memory card.
    • These are the only tools that we will need. 4 screwdrivers and a tweezer.

    • In the next photo we can see the console, the joystick, the wires and a memory card.

  3. Deze stap is niet vertaald. Help het te vertalen

    In the Back, in this case we have a Ethernet adapter, to play online and to use with a Hdd. And the cooler,
    • In the Back, in this case we have a Ethernet adapter, to play online and to use with a Hdd.

    • And the cooler,

    • The power switch

    • The AC in.

    • The Av out

    • And the digital output (optical)

  4. Deze stap is niet vertaald. Help het te vertalen

    Lets start the teardown. At first we use a Flathead screwdriver to remove the ethernet adapter. Remove these 2 screws with a Flathead screwdriver. And is quite simple to pull.
    • Lets start the teardown. At first we use a Flathead screwdriver to remove the ethernet adapter.

    • Remove these 2 screws with a Flathead screwdriver.

    • And is quite simple to pull.

  5. Deze stap is niet vertaald. Help het te vertalen

    This is the expansion bay, where the hard drive goes.
    • This is the expansion bay, where the hard drive goes.

  6. Deze stap is niet vertaald. Help het te vertalen

    Turn the console upside down. Using a small Flathead screwdriver, remove the screw protections. In this model, we have 8 of them.
    • Turn the console upside down.

    • Using a small Flathead screwdriver, remove the screw protections. In this model, we have 8 of them.

  7. Deze stap is niet vertaald. Help het te vertalen

    Under the protection, suprise! a screw! Remove all eight (8) screws with your Philips "0" screwdriver. Yes, hard work!
    • Under the protection, suprise! a screw!

    • Remove all eight (8) screws with your Philips "0" screwdriver.

    • Yes, hard work!

  8. Deze stap is niet vertaald. Help het te vertalen

    Put the console in the normal horizontal position, and pull the top cover from back to front. Put the console in the normal horizontal position, and pull the top cover from back to front.
    • Put the console in the normal horizontal position, and pull the top cover from back to front.

  9. Deze stap is niet vertaald. Help het te vertalen

    This model has a flat cable to the reset and eject button. Take extreme caution to not destroy it. Remove the button structure just pulling with a small Flathead screwdriver. Remove the button structure just pulling with a small Flathead screwdriver.
    • This model has a flat cable to the reset and eject button. Take extreme caution to not destroy it.

    • Remove the button structure just pulling with a small Flathead screwdriver.

  10. Deze stap is niet vertaald. Help het te vertalen

    The button structure comes out of the case. It have some tape to prevent a new destruction. Yes, I already destroyed this flat cable.
    • The button structure comes out of the case. It have some tape to prevent a new destruction. Yes, I already destroyed this flat cable.

  11. Deze stap is niet vertaald. Help het te vertalen

    Remove the two screws with a Philips "0" screwdriver to deatach the controller port. Remove the two screws with a Philips "0" screwdriver to deatach the controller port. Remove the two screws with a Philips "0" screwdriver to deatach the controller port.
    • Remove the two screws with a Philips "0" screwdriver to deatach the controller port.

  12. Deze stap is niet vertaald. Help het te vertalen

    Here we remove the screws from the cooler and the main power switch Here we remove the screws from the cooler and the main power switch
    • Here we remove the screws from the cooler and the main power switch

  13. Deze stap is niet vertaald. Help het te vertalen

    Pull the cooler up, but take care to not destroy the wire. Pull up the fan grid.
    • Pull the cooler up, but take care to not destroy the wire.

    • Pull up the fan grid.

  14. Deze stap is niet vertaald. Help het te vertalen

    The power cable go to inside the case. Is better let to remove in a further step. The fan wire also go to inside the case. Take extreme care to not destroy it.
    • The power cable go to inside the case. Is better let to remove in a further step.

    • The fan wire also go to inside the case. Take extreme care to not destroy it.

  15. Deze stap is niet vertaald. Help het te vertalen

    Lets turn the console upside down again, with caution because the pieces are locked, and just in the next step we can remove them. Lets turn the console upside down again, with caution because the pieces are locked, and just in the next step we can remove them. Lets turn the console upside down again, with caution because the pieces are locked, and just in the next step we can remove them.
    • Lets turn the console upside down again, with caution because the pieces are locked, and just in the next step we can remove them.

  16. Deze stap is niet vertaald. Help het te vertalen

    Lets remove the bottom case. Lets remove the bottom case.
    • Lets remove the bottom case.

  17. Deze stap is niet vertaald. Help het te vertalen

    This is the power source board. remove the 4 screws where I marked in blue. This is the power source board. remove the 4 screws where I marked in blue. This is the power source board. remove the 4 screws where I marked in blue.
    • This is the power source board. remove the 4 screws where I marked in blue.

  18. Deze stap is niet vertaald. Help het te vertalen

    Looking from the back, pull up the board, releasing from the pins of the main board. Finally you can remove the power switch. And this is the power source board.
    • Looking from the back, pull up the board, releasing from the pins of the main board.

    • Finally you can remove the power switch.

    • And this is the power source board.

    • When working on the power supply, be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply. Only handle the board by the edges.

  19. Deze stap is niet vertaald. Help het te vertalen

    Now we remove the expansion bay grid. And now is the time to remove the fan wire from the main board, using a precision tweezer. But..  I can't, it is simply stuck. I already removed this ealier, but now is harder, so I will try later, in the end of the teardown. And now is the time to remove the fan wire from the main board, using a precision tweezer. But..  I can't, it is simply stuck. I already removed this ealier, but now is harder, so I will try later, in the end of the teardown.
    • Now we remove the expansion bay grid.

    • And now is the time to remove the fan wire from the main board, using a precision tweezer. But.. I can't, it is simply stuck. I already removed this ealier, but now is harder, so I will try later, in the end of the teardown.

  20. Deze stap is niet vertaald. Help het te vertalen

    Remove the isolation cover from the metal case. Remove the small screws using a thin crosshead screwdriver. And release the metal case from the DVD player, as indicated, using a small flat screwdriver
    • Remove the isolation cover from the metal case.

    • Remove the small screws using a thin crosshead screwdriver.

    • And release the metal case from the DVD player, as indicated, using a small flat screwdriver

  21. Deze stap is niet vertaald. Help het te vertalen

    Now you can remove the metal case and find the main board. Look, the flat cables! Now is the time to remove them. Be gentle please. Look, the flat cables! Now is the time to remove them. Be gentle please.
    • Now you can remove the metal case and find the main board.

    • Look, the flat cables! Now is the time to remove them. Be gentle please.

  22. Deze stap is niet vertaald. Help het te vertalen

    There are 2 more and the DVD player is free. There are 2 more and the DVD player is free. There are 2 more and the DVD player is free.
    • There are 2 more and the DVD player is free.

  23. Deze stap is niet vertaald. Help het te vertalen

    Now you can turn upside down again, and remove the metal protection. This is the other side of the main board.
    • Now you can turn upside down again, and remove the metal protection.

    • This is the other side of the main board.

  24. Deze stap is niet vertaald. Help het te vertalen

    Well, the try to remove the cooler wire was a total failure. The plug is made to deatach, but it is old. The plug had turned into one piece, and broke the soldering. Well, I'll find a way to fix it. I always do =)
    • Well, the try to remove the cooler wire was a total failure.

    • The plug is made to deatach, but it is old. The plug had turned into one piece, and broke the soldering.

    • Well, I'll find a way to fix it. I always do =)

  25. Deze stap is niet vertaald. Help het te vertalen

    This is the end of the teardown.
    • This is the end of the teardown.

    • From top, from the left: Ethernet adapter, Ps2 case, Hdd, Cooler, Cooler grid, bottom metal cover protection, screws protectors, screws, Controller board, Power swtich, Power source board, Plastic cover to isolate the power source board, top metal cover, DVD Drive, Expansion Bay cover, main board, reset/eject structure.

Pollux

Lid sinds: 22-10-09

643 Reputatie

1 Handleiding geschreven

8 Opmerkingen

reverse procedures..step by step..

a to z cellutions belize - Antwoord

Yep in reverse, take your time or you'll be like me breaking things and having to rig it haha. Put the shielding back together, drive, power board, the other shield for hard drive. Everything, plug all connections. Even power-reset buttons. Then put it on the bottom casing, connect controller ports and close it up with top casing.

juan hernandez - Antwoord

How did you fix the flat cable?

Bigs - Antwoord

If a cable is ripped or broken, unfortunately there is no way to fix it. You will have to replace the cable.

Molten Toast -

I put a lot of layers of tape on mine, the last owner of my system was very naughty and disassembled the system when it was still under warranty, so the cable was brokem

John Doe -

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 69

Afgelopen 7 dagen: 342

Afgelopen 30 dagen: 1,574

Altijd: 114,156