Unibody 8x SATA SuperDrive (Pre-Mid 2009)

  • Unibody 8x SATA SuperDrive (Pre-Mid 2009) / Used
Unibody 8x SATA SuperDrive (Pre-Mid 2009)

Staat: Gebruikt

US$ 49,99

US$ 49,99

We zullen een bericht sturen als het product weer op voorraad is.

MacBook-reparatiesets voor batterijen

Vanaf $69.99

Buy Now

MacBook-reparatiesets voor batterijen

Vanaf $69.99

Buy Now

Productdetails

Beschrijving

Beschrijving

Mankind's early attempts at spinning amounted to sending fleets of feather-coated sailboats in opposite directions off the ends of the earth, in effort to tickle the resting turtle on whose back it rested. Delegate the dizziness to your MacBook today with our Unibody 8x SATA SuperDrive (Pre-Mid 2009).

Dual-layer SATA drive. Metal mounting bracket and orange ribbon cable not included.

Note: This optical drive has a different connector than previous Apple drives.

Compatibiliteit

Compatibiliteit

  • All 13" Unibody MacBooks (Model A1278)
  • Late 2008 or Early 2009 Unibody 15" MacBook Pros
  • Early or Mid 2009 Unibody 17" MacBook Pros

Specificaties

Specificaties

Part #:
661-5147
Speed:
8x DVD-R write
4x DVD-RW write
8x DVD+R write
4x DVD+RW write
4x DVD+R (DL) write
24x CD-R write
10x CD-RW write
8x DVD read
24x CD read

Compatibiliteit

MacBook Pro 15" Unibody Late 2008 and Early 2009
2.4 GHz
2.53 GHz
2.66 GHz
2.8 GHz
2.93 GHz
MacBook Pro 17" Unibody
2.66 GHz (Early 2009)
2.8 GHz (Mid 2009)
2.93 GHz (Early 2009)
3.06 GHz (Mid 2009)
MacBook Unibody Model A1278
2 GHz
2.4 GHz

Reparatieverhalen

Avatar
Sondre Selnes's Story Photo #257497

Mijn probleem

The fan on my MacBook Pro was reaching its end. It was terrible noisy ! I was in the middle of a programming project for the iPhone and making video guide for the new software, when the fan of my computer broke down. I had to stop all recording (Big Blue Yeti mic, ScreenFlow recording...).

Mijn oplossing

The vi . . .

Avatar

Mijn probleem

Old drive was becoming unreliable

Mijn oplossing

Instructions were spot on.

Mijn advies

Tweezers are a must on this repair. The small screws are easy to remove but the bulk of the time is spent replacing them when you do not use tweezers. I used a plastic knife rather than a spudger. Worked just fine.

Avatar

Mijn probleem

Fan bearing started getting noisy and then fan started to be slow/intermittent causing overheat shutdown of the MacBook.

Mijn oplossing

Watched your video to see what I was in for. Seemed relatively straightforward. Opened up the case and got to the fan. 2 of the 3 Philips screws came out easy. One was REALLY torqu . . .

Avatar

Mijn probleem

The old fan had worn out bearings which caused lots of noise and bad performance.

Mijn oplossing

The switch went well. Took about 30 minutes because the screws were stripped. The comments were very helpful.

Mijn advies

If the screws are stripped, take a similar size flat screwdriver and put at 45 degrees into the screw so the s . . .

Avatar

Mijn probleem

CPU temperatures had started to spike on my laptop (80C or higher) while doing mundane things at low percentages of CPU, and fan didn't spin up to cool the machine. Apple did diagnostics, said all was well. Temperature Gauge Pro detected a problem with fan, however, so I ordered a replacement to s . . .

Avatar

Mijn probleem

Loud noises prompted me to take my Macbook Pro to the Genius Bar. They wanted to keep it for 3+ days to replace the fan, at a pretty significant cost. I happen to be blessed with a very smart teenager who cut his teeth on taking Mac's apart. Quick order on iFixit, an even faster delivery, and voi . . .

Avatar

Mijn probleem

battery only lasted about an hour fully charged, and it the whole computer would rapidly overheat.

Mijn oplossing

A bit scary. The battery went in without a hitch, but when removing the old fan, the socket ripped off of the circuit board. I ended up soldering the individual wires back on. Now it works great though! . . .

Avatar

Mijn probleem

The old fan had become noisy - bearings worn out probably. (After taking it out, I could see the blades spun crooked.)

Mijn oplossing

Pretty easy repair, only 3 internal screws. The connector is a little tricky since it's so small, you tend to think you're gonna break it. Go slowly around the edges and it'll com . . .

Avatar

Mijn probleem

My fan was making a god awful sound whenever my macbook would start heating up. This had been happening ever since an unfortunate crepe experience where I managed to spill lemon-sugar syrup into my keyboard.

Mijn oplossing

The repair was incredibly straight forward. It was a very minimal risk procedure.

Mijn advies

Be prepared . . .

Avatar

Mijn probleem

The blades on the original fan had broken and was making a lot of noise when it spun up.

Mijn oplossing

I've opened the computer many times before so the repair was a piece of cake. ~5 minutes in total.

Mijn advies

-

Geef meer weer