Repareer je spullen Gemeenschap Winkel

iPhone XR 배터리 교체

Waarschuwing: Je bewerkt een vooraf vereiste handleiding. Alle wijzigingen die je hierin maakt, beïnvloeden de handleiding die deze stap bevat.

Terug naar de handleiding
Engels
Koreaans
Stap 3
iPhone XR Battery Replacement: stap 0, afbeelding 1 van 3 iPhone XR Battery Replacement: stap 0, afbeelding 2 van 3 iPhone XR Battery Replacement: stap 0, afbeelding 3 van 3

  • Try to keep the adhesive strips flat and unwrinkled during this procedure; twisted or wrinkled strips will stick together and break instead of pulling out cleanly.

  • Additionally, do not press down on the battery as you pull the strips. Pressing on the battery creates pressure points that can snag and break the adhesive.

  • Slowly pull one battery adhesive tab away from the battery, towards the bottom of the iPhone.

  • Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the rear case. For best results, pull the strip at as low an angle as possible, without snagging it on any of the iPhone's other components.

  • The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.

  • If the battery adhesive tabs break during the removal process, use your fingers or blunt tweezers to retrieve the remaining length of adhesive, and continue pulling.

  • If any of the adhesive strips break underneath the battery and cannot be retrieved, try to remove the remaining strips, and then proceed as instructed below.

이 과정에서 접착 스트립을 평평하고 주름이 생기지 않도록 하십시오; 꼬이거나 주름진 스트립은 깨끗하게 잡아당겨지는 대신 서로 달라 붙어 파손됩니다.

또한, 스트립을 잡아당길 때 배터리를 누르지 마십시오. 배터리를 누르면 압력 점이 생겨서 접착제가 걸리거나 찢어질 수 있습니다.

배터리 접착 탭 한 개를 천천히 배터리에서 iPhone 아래쪽으로 잡아당겨 주십시오.

배터리와 후면 케이스 사이에서 스트립이 빠져나올 때까지 스트립을 일정한 힘으로 당겨 주십시오. 최상의 결과를 얻으려면 iPhone의 다른 부품에 걸리지 않게 최대한 낮은 각도로 스트립을 당겨 주십시오.

스트립은 원래 길이의 몇 배로 늘어납니다. 필요하다면 스트립을 잡아당기면서 늘어난 스트립을 배터리에 가깝게 다시 잡고 당겨주십시오.

제거 과정에서 배터리 접착 탭이 끊어지는 경우 손가락 또는 무딘 핀셋을 사용하여 남아있는 접착제를 찾아 계속 당겨주십시오.

배터리 아래에서 접착 스트립이 끊어져 회수할 수 없는 경우 나머지 스트립을 제거하려 노력하고 아래 지침에 따라 진행하십시오.

[* icon_caution] Try to keep the adhesive strips flat and unwrinkled during this procedure; twisted or wrinkled strips will stick together and break instead of pulling out cleanly.
[* icon_caution] Additionally, do not press down on the battery as you pull the strips. Pressing on the battery creates pressure points that can snag and break the adhesive.
[* black] ***''Slowly''*** pull one battery adhesive tab away from the battery, towards the bottom of the iPhone.
[* black] Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the rear case. For best results, ***pull the strip at as low an angle as possible***, without snagging it on any of the iPhone's other components.
[* icon_note] The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.
-[* black] If the battery adhesive tabs break during the removal process, use your fingers or blunt tweezers to retrieve the remaining length of adhesive, and continue pulling.
+[* black] If the battery adhesive tabs break during the removal process, use your fingers or [product|IF145-020-4|blunt tweezers] to retrieve the remaining length of adhesive, and continue pulling.
[* icon_caution] If any of the adhesive strips break underneath the battery and cannot be retrieved, try to remove the remaining strips, and then proceed as instructed below.

Je bijdragen zijn gelicentieerd onder de open source Creative Commons-licentie.