Inleiding

The guide takes place from the Camera Lens Assembly guide.

Onderdelen

Geen onderdelen nodig.

Locate the memory card and battery card latch on the bottom of the camera.
  • Locate the memory card and battery card latch on the bottom of the camera.

  • Slide the latch to the open position.

Voeg opmerking toe

Open the battery latch, and slide the battery release lever to the right.
  • Open the battery latch, and slide the battery release lever to the right.

Voeg opmerking toe

Remove the battery from the camera.
  • Remove the battery from the camera.

Voeg opmerking toe

Using a size #00 Phillips screwdriver, remove the three 4.58 mm screws on the bottom of the camera.
  • Using a size #00 Phillips screwdriver, remove the three 4.58 mm screws on the bottom of the camera.

  • Use this screwdriver for all screws in the device.

Voeg opmerking toe

Remove the 3.15 mm screw on the left side of the camera.
  • Remove the 3.15 mm screw on the left side of the camera.

Voeg opmerking toe

Remove the left side casing. Remove the left side casing.
  • Remove the left side casing.

Voeg opmerking toe

Remove the two 3.15 mm screws on the right side of the camera.
  • Remove the two 3.15 mm screws on the right side of the camera.

Voeg opmerking toe

Remove the bottom right panel.
  • Remove the bottom right panel.

Voeg opmerking toe

Gently remove the back casing. Start at the bottom and carefully pry towards the top to get this piece free.
  • Gently remove the back casing.

  • Start at the bottom and carefully pry towards the top to get this piece free.

Voeg opmerking toe

Remove the two black 5.35 mm screws that hold in the front faceplate. There may be a third screw the the right of the lens assembly.
  • Remove the two black 5.35 mm screws that hold in the front faceplate.

  • There may be a third screw the the right of the lens assembly.

Voeg opmerking toe

Carefully remove the upper assembly, which houses the buttons and the flash battery. Carefully remove the upper assembly, which houses the buttons and the flash battery. Carefully remove the upper assembly, which houses the buttons and the flash battery.
  • Carefully remove the upper assembly, which houses the buttons and the flash battery.

Voeg opmerking toe

Carefully remove the front casing after verifying that the thin plastic around the lens is not still attached.
  • Carefully remove the front casing after verifying that the thin plastic around the lens is not still attached.

Voeg opmerking toe

Remove the three black 5mm screws attached to the lens frame. Remove the three black 5mm screws attached to the lens frame.
  • Remove the three black 5mm screws attached to the lens frame.

Voeg opmerking toe

Remove the lens frame.
  • Remove the lens frame.

Voeg opmerking toe

Lift out the circuit board as shown.
  • Lift out the circuit board as shown.

Voeg opmerking toe

Lift the two black latches that hold the connector ribbons in place. Disconnect the two ribbons.
  • Lift the two black latches that hold the connector ribbons in place.

  • Disconnect the two ribbons.

Voeg opmerking toe

Remove the lens assembly as shown.
  • Remove the lens assembly as shown.

Voeg opmerking toe

Remove four 4mm screws from the lens assembly.
  • Remove four 4mm screws from the lens assembly.

Voeg opmerking toe

Carefully turn over the assembly. Carefully turn over the assembly.
  • Carefully turn over the assembly.

Voeg opmerking toe

Remove the Fixed Frame Unit by separating it from the assembly. Remove the Direct Frame Unit from the assembly.
  • Remove the Fixed Frame Unit by separating it from the assembly.

  • Remove the Direct Frame Unit from the assembly.

Voeg opmerking toe

Remove the 1st lens frame from the lens assembly.
  • Remove the 1st lens frame from the lens assembly.

Voeg opmerking toe

Detach the 2nd Frame Unit from the assembly.
  • Detach the 2nd Frame Unit from the assembly.

Voeg opmerking toe

Remove the 4mm screw from the lens housing.
  • Remove the 4mm screw from the lens housing.

Voeg opmerking toe

Separate the lens housing.
  • Separate the lens housing.

  • Replace the lens by gently prying away from the assembly.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

4 andere personen hebben deze handleiding voltooid.

Caleb Fink

Lid sinds: 11-10-10

186 Reputatie

2 handleidingen geschreven

Team

Cal Poly, Team 9-22, Regan Fall 2010 Lid van Cal Poly, Team 9-22, Regan Fall 2010

CPSU-REGAN-F10S9G22

4 Leden

8 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 2

Afgelopen 30 Dagen: 15

Altijd: 11,870