Repareer je spullen Gemeenschap Winkel

iPod Shuffle 2nd Generation Logic Board Assembly Replacement

Geschreven door: Andrew Bookholt (en 3 andere bijdragers)
  • Reacties: 3
  • Favorieten: 6
  • Voltooide reparaties: 20

Moeilijkheid

Gemiddeld

Stappen

10

Tijd vereist

Stel een tijd voor??

Secties

1

Markeringen

0

Inleiding

Use this guide to remove your Shuffle's logic board assembly. The logic board assembly includes the logic board, headphone jack, and battery.

Gereedschap

Onderdelen

Geen onderdelen opgegeven.

  1. Before beginning, be sure your Shuffle is turned off as shown.

    • Before beginning, be sure your Shuffle is turned off as shown.

    Bewerken

  2. Use the edge of an iPod opening tool to pry the plastic cover off the headphone jack side of the Shuffle. Remove the plastic cover and set it aside.

    • Use the edge of an iPod opening tool to pry the plastic cover off the headphone jack side of the Shuffle.

    • Remove the plastic cover and set it aside.

    Bewerken

  3. Remove the two Phillips screws from the headphone jack side of the Shuffle.

    • Remove the two Phillips screws from the headphone jack side of the Shuffle.

    Bewerken

  4. Use the edge of an iPod opening tool to remove the steel cover from the headphone jack side of the Shuffle. Use the edge of an iPod opening tool to remove the steel cover from the headphone jack side of the Shuffle.

    • Use the edge of an iPod opening tool to remove the steel cover from the headphone jack side of the Shuffle.

    Bewerken

  6. Use the edge of an iPod opening tool to pry the plastic cover off the controls side of the Shuffle. Remove the plastic cover and set it aside.

    • Use the edge of an iPod opening tool to pry the plastic cover off the controls side of the Shuffle.

    • Remove the plastic cover and set it aside.

    Bewerken

  7. Use a pair of tweezers to remove the hold and shuffle sliders from the Shuffle. Use a pair of tweezers to remove the hold and shuffle sliders from the Shuffle.

    • Use a pair of tweezers to remove the hold and shuffle sliders from the Shuffle.

    Bewerken

  8. Remove the two Phillips screws on the controls side of the Shuffle.

    • Remove the two Phillips screws on the controls side of the Shuffle.

    Bewerken

  9. Use the edge of an iPod opening tool to remove the steel plate from the controls side of the Shuffle. Use the edge of an iPod opening tool to remove the steel plate from the controls side of the Shuffle.

    • Use the edge of an iPod opening tool to remove the steel plate from the controls side of the Shuffle.

    Bewerken

  10. Use the edge of an iPod opening tool to slightly pry the steel plate on the headphone jack side of the Shuffle away from the lip cut into the outer case.

    • Use the edge of an iPod opening tool to slightly pry the steel plate on the headphone jack side of the Shuffle away from the lip cut into the outer case.

    Bewerken

  11. Use your iPod opening tool to push the logic board assembly out of the outer case enough to grab the logic board by its edges. Pull the logic board assembly out of the outer case.

    • Use your iPod opening tool to push the logic board assembly out of the outer case enough to grab the logic board by its edges.

    • Pull the logic board assembly out of the outer case.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

20 andere personen hebben deze handleiding voltooid.

0 Opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 1

Afgelopen 7 dagen: 10

Afgelopen 30 dagen: 39

Altijd: 18,067