Ga door naar hoofdinhoud

iPhone X Vervanging van de batterij

Wat je nodig hebt

Video overzicht

  1. iPhone X Vervanging van de batterij, Pentalobe schroeven: stap 1, afbeelding 1 van 1
    • Ontlaad je batterij, voordat je begint, tot onder de 25%. Een geladen lithium-ion batterij kan in brand vliegen en/of exploderen als deze per ongeluk wordt doorboord.

    • Schakel je iPhone uit voordat je begint met het uit elkaar halen van je telefoon.

    • Verwijder de twee 6.9 mm lange pentalobe schroeven aan de onderkant van de iPhone.

    • Als de schroeven zijn beschadigd, vervang je de schroeven.

    • Het openen van het scherm van de iPhone zal de waterdichte sluiting van de telefoon aantasten. Zorg dat je vervangende sluitingen klaar hebt liggen voordat je verdergaat of zorg ervoor dat je telefoon niet wordt blootgesteld aan water als je ervoor kiest de sluitingen niet te vervangen.

    There are 6.81mm long screws!

    Daniel - Antwoord

    One of the pentalobe screws is stripped :( - suggestions for how to get it out?

    cgtyoder - Antwoord

    same situation here

    kaunomarcius - Antwoord

    Same issue for me too, how do I get the stripped screw out?

    patronics - Antwoord

    Update: I was able to get the “stripped” screw out using another Pentalobe-2 screwdriver bit from another company. It seems it wasn’t the screw, but the screw driver that was actually stripped. Hence why the other screwdriver kit I got came with 3 of this bit, I suppose.

    patronics - Antwoord

    I ended up going to a jewelry store, and they drilled down into the screw, with of course an incredibly tiny bit. That allowed me to insert the P2 driver, and I was able to unscrew it at that point. Good luck!

    cgtyoder - Antwoord

    Same issue with the stripping. The tip of the iFixit P2 head in my $70 kit just ground off on the first screw and that was that. Not much you can do.

    Kyle Harris - Antwoord

    yes correct the same happened to me, the screws were perfect shaped never been open and as soon as i used the P2 it stripped the screws, seems like the P2 is slightly smaller but Dremel kit with a very small drill bits and precise knife tool is the way to go.

    Dulce Vidal - Antwoord

    This step in automatically followed through, without any thought. Why remove these screws? Can anybody explain? The Screen is detachable all the same, with them well screwed in…

    Uri - Antwoord

    These screws attach to a plate that’s part of the screen half of the phone. If you succeed in detaching the screen without removing those, it would seem reasonable that you will have damaged that plate or its ability to keep the two halves together.

    Dan Long -

    @Dan Long is right

    Uri -

    Clean out the pentalobe screw heads first so the tool goes all the way in. A small sewing needle works well to loosen any build up and then press some putty/chewing gum into the screw head and pull away quickly for a final clean out.

    William Olstad - Antwoord

    The this kit should include screws because you’re going to strip them. Can’t even get past step one. Did anybody figure this out

    justin - Antwoord

    Never opened my phone ever, when I went to look at the first step.. I noticed one of my screws was stripped. I thought it was impossible, but I removed the non stripped one, then once I got to the stripped one.. I learned my assumptions were correct. I bought this one straight from the apple site years ago ahaha Any tips to remove the stripped screw?

    Clarence Williams - Antwoord

    William Olstad's tip about cleaning the screws with a needle and a bit of poster putty worked well for me. There was a lot of crud in there! The opening is shallow, so it's easy to see how the screwdriver wouldn't catch with even a bit of grit in the way, No problem getting the pentalobe screws out with the ifixit screwdriver.

    punkinann - Antwoord

    If all else fails, very carefully cut a slot across the head of the screw with a Dremel tool using a diamond bit that dentist will gladly give you - I ask my dentist for used bits; and chuck them in a drill bit chuck designed for Dremel. The slot allows you to use a tiny, straight blade screwdriver. You can reuse the screw or replace it with a new pentalobe screw.

    Dan Smith - Antwoord

  2. iPhone X Vervanging van de batterij, Markeer je plectrums: stap 2, afbeelding 1 van 3 iPhone X Vervanging van de batterij, Markeer je plectrums: stap 2, afbeelding 2 van 3 iPhone X Vervanging van de batterij, Markeer je plectrums: stap 2, afbeelding 3 van 3
    • Je kunt de onderdelen in je telefoon gemakkelijk beschadigen met het te diep inbrengen van je openingsplectrum. Volg deze stap om je plectrum te markeren en schade aan je toestel te voorkomen.

    • Plaats op 3 mm van de punt van je plectrum een markering met een stift.

    • Je kunt op iedere punt voor een andere markering kiezen.

    • Als alternatief kun je ook een munt als markering gebruiken in plaats van een stift. Plak hierbij de munt op de plectrum zodat de munt tegen je telefoon aandrukt zodra deze een bepaalde diepte bereikt.

    Got to step 2 and realized the fix kit doesn't include an opening pick! Looks like a guitar pick, and I have those lying around. Is that expected? Looks like the pick is used in many steps below. There's a little blue crowbar that isn't mentioned in the instructions. Perhaps that replaces the opening pick?

    Sloan Looney - Antwoord

    Hi! I can't see which guide you were using when writing this comment. Can you reply here with which guide and fix kit you used?

    Clay Eickemeyer -

    I see you posted this in Meta. I hope it's resolved soon! In the meantime, a guitar pick may work well enough for your repair.

    Clay Eickemeyer -

    what fix kit?

    Meow Purr -

    My fix kit didn't include an opening pick either

    WILLIAM HARRIS - Antwoord

    Make sure you check inside the black boxes after emptying them. My pick was stuck inside one of the boxes.

    AndyF - Antwoord

    My AliExpress refurbished screen came with a pick that has a coin-like circle that pops out, so no modification was necessary

    Gijs Leegwater - Antwoord

  3. iPhone X Vervanging van de batterij, Plak tape over eventuele barsten in het scherm: stap 3, afbeelding 1 van 3 iPhone X Vervanging van de batterij, Plak tape over eventuele barsten in het scherm: stap 3, afbeelding 2 van 3 iPhone X Vervanging van de batterij, Plak tape over eventuele barsten in het scherm: stap 3, afbeelding 3 van 3
    • Als het scherm van je iPhone gebarsten is, kun je wat tape over de barsten plakken om te voorkomen dat het scherm verder beschadigd raakt tijdens dit proces. Zo verklein je ook het risico op fysieke schade.

    • Plak een aantal lagen tape op het scherm van de iPhone tot het gehele scherm bedekt is.

    • We raden je ten sterkste aan om tijdens deze stap een veiligheidsbril te dragen zodat je je ogen beschermt tegen eventueel loskomende glasscherven.

    • Als het je in de volgende stappen niet lukt om de zuignap op het scherm te bevestigen, kun je ervoor kiezen om een stuk duct tape in een handvatvorm op het scherm te plakken. Hiermee kun je dan het scherm omhoog tillen om een opening te creëren.

    • Als alternatief kun je er ook voor kiezen om de zuignap met secondelijm op het scherm vast te plakken.

  4. iPhone X Vervanging van de batterij, Instructies voor de anti-klem: stap 4, afbeelding 1 van 3 iPhone X Vervanging van de batterij, Instructies voor de anti-klem: stap 4, afbeelding 2 van 3 iPhone X Vervanging van de batterij, Instructies voor de anti-klem: stap 4, afbeelding 3 van 3
    • De volgende twee stappen introduceren de Anti-Klem, een handige tool die we aanraden aan iedereen die regelmatig reparaties uitvoert. Als je de Anti-Klem niet gebruikt, sla dan de volgende drie stappen over voor een alternatieve methode.

    • Voor uitgebreider instructies voor het gebruik van de Anti-Klem, lees je deze handleiding door.

    • Trek de blauwe hendel naar achteren zodat de anti-klem vrij kan bewegen. (Op deze manier deactiveer je de openingsstand van de anti-klem.)

    • Schuif de armen over de linker- of rechterzijde van je iPhone.

    • Plaats de zuignappen dichtbij de onderkant van de telefoon—één op de voorkant en één aan de achterkant.

    • Druk beide zuignappen aan, om zuigkracht uit te oefenen op de gewenste plek.

    • Als het oppervlak waarop de zuignappen zich moeten vastzuigen te glad is, kun je wat tape gebruiken voor meer grip.

  5. iPhone X Vervanging van de batterij: stap 5, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 5, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 5, afbeelding 3 van 3
    • Trek het blauwe handvat naar voren om de armen van de anti-klem te vergrendelen.

    • Draai het handvat 360 graden met de klok mee of tot de zuignappen uit beginnen te rekken.

    • Zorg dat de zuignappen op één lijn met elkaar zitten voordat je begint met het openen van het toestel. Als je ziet dat de zuignappen niet meer op één lijn zitten, maak je ze los en breng je ze weer op de juiste positie aan.

  6. iPhone X Vervanging van de batterij: stap 6, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 6, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 6, afbeelding 3 van 3
    • Verwarm een iOpener en plaats deze tussen de armen van de anti-klem op je telefoon.

    • Je kunt ook een föhn, heteluchtpistool, of een kookplaat gebruiken, maar wees bij het gebruik hiervan extra voorzichtig. Te veel warmte kan tot warmteschade leiden. Vooral het scherm en de batterij zijn hier erg vatbaar voor.

    • Vouw de iOpener zodat deze op de onderkant van de iPhone komt te liggen.

    • Geef de lijm een minuutje de tijd om los te komen zodat de anti-klem een opening kan creëren.

    • Steek een plectrum in de opening onder het scherm en de plastic rand, en niet onder het scherm zelf.

    • Als de anti-klem er niet in slaagt een opening te creëren die groot genoeg is voor je plectrum gebruik je meer warmte en draai je het blauwe handvat een kwartslag met de klok mee.

    • Draai het handvat nooit verder dan een kwartslag per keer en wacht een minuut voordat je de anti-klem weer besluit aan te draaien. Laat de anti-klem het werk voor je doen.

    • Sla de volgende drie stappen over.

    DO NOT separate the glass from the plastic bumper or rim around it. These instructions don't clarify that the pick has to be inserted between the plastic rim and the metal body. It is likely that the glass will lift slightly off the plastic surround before the plastic will lift out of the metal body. I had success sliding a card or pick back and forth along the bottom edge of the plastic rim while pulling on the suction cup. Eventually there was a space large enough for the pick to go under the plastic rim.

    Anessa - Antwoord

    Thanks for pointing this out! I'll revise this step to clarify this point.

    Arthur Shi -

  7. iPhone X Vervanging van de batterij: stap 7, afbeelding 1 van 1
    • Het verwarmen van de onderkant van de iPhone helpt de lijm, die het scherm op z'n plek houdt, te verzachten, wat het makkelijker maakt om de telefoon te openen.

    • Gebruik een föhn of een warmtepistool, of prepareer een iOpener en leg deze op de onderkant van de iPhone gedurende ongeveer een minuut om zo de lijm die eronder zit te verzachten.

    General tip regarding heating necessary to remove adhesive:

    consider using a heated tip of a small screwdriver or metal spudger (not the one made of plastic, provided in kit), rather than to heat the device itself.

    Uri - Antwoord

    You then need to be careful about the temp of the tool which if hot enough can melt plastic components or harm them. Keeping the heat source (heat gun) far enough away from the object that you’ll eventually melt the glue but would be much harder to melt components. I try to keep 4” or 5” gap between the source & object

    Sandman619 -

    Thanks for the info. Could a air convector do the job

    dominique.br - Antwoord

    When opening a device that has previously been worked on, and on which the adhesive might not have been replaced, be extremely carful when opening the phone. It will open much more easily than expected. If you’re not careful you might rip a cable.

    jonpol - Antwoord

    Is this tool required or can I just use the Anti-Clamp by itself.

    Mikail - Antwoord

    If you have a 3d printer, heat the bed to 80c and put the phone screen side down on it for 30 secs

    philip.joseph123 - Antwoord

  8. iPhone X Vervanging van de batterij: stap 8, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 8, afbeelding 2 van 2
    • Als je een enkele zuignap met handvat gebruikt, druk deze dan vast aan de onderkant van de telefoon, maar vermijd het bolle deel van het glas.

    If you were using some form of screen protector, it may come off first as soon as you pull on the suction cup. Do not be alarmed. That is normal behavior.

    Alain-Daniel Wa-Baguma - Antwoord

    3m VSB double stick tape will stick to the screen when the suction cups fail (see my comment on step 1)

    Tawan Khamapirad - Antwoord

  9. iPhone X Vervanging van de batterij: stap 9, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 9, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 9, afbeelding 3 van 3
    • Trek de zuignap omhoog met een stevige, constante kracht om zo een kleine opening tussen het voorste paneel en de achterste behuizing te creëren.

    • Steek een openingsplectrum in de opening onder de plastic rand van het scherm, niet onder het scherm.

    • De waterdichte lijm die het scherm op z'n plek houdt is erg sterk; het creëren van de opening kan dus heel wat kracht vereisen. Als je moeite hebt met het openen van de telefoon, dien dan meer warmte toe en wiebel het scherm op en neer om de lijm te verzachten totdat de opening groot genoeg is voor je tool.

    In addition to safety goggles, I would recommend you also wear good gloves to avoid getting cut with the glass as you try to pry it open.

    Alain-Daniel Wa-Baguma - Antwoord

    The top about applying more heat and gently rocking the screen up and down to weaken the adhesive did the trick for me. Thank you!

    Monil Shah - Antwoord

    There needs to be more clarity on where to shove the opening pick into. There is actually two openings that the pry tool can be forced into: one below the black plastic bezel, and one above the black plastic bezel. When I heated my screen with a warming pad and pulled up the suction cup, it actually pried apart above the black plastic bezel which removed the touch screen from the display panel. With this being the first newer iPhone I'd opened since the 3GS, I didn't realize that I was opening the wrong opening as the directions only mentioned one opening and did not warn of this. I was pretty disappointed in the lack of mentioning this, as I was taking my time and following it to the tee. As a result, it destroyed my original iPhone screen.

    Caleb Davison - Antwoord

    DO NOT separate the glass from the plastic bumper or rim around it. As someone else noted, these instructions don't clarify that the pick has to be inserted between the plastic rim and the metal body of the phone. When pulling upwards with the suction cup, it is likely that the glass will lift slightly off the plastic surround before the plastic will lift out of the metal body. I had success sliding a card or pick back and forth along the bottom edge of the plastic rim while pulling on the suction cup. Eventually there was a space large enough for the pick to go under the plastic rim.

    Anessa - Antwoord

    Thank you for pointing this out! I've updated the step to reflect this.

    Arthur Shi -

    The suction cup doesn't work at all... The minimum force I apply to lift it up, it comes off completely. This is very frustrating!!!

    Mario Silva - Antwoord

  10. iPhone X Vervanging van de batterij: stap 10, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 10, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 10, afbeelding 3 van 3
    • Schuif je openingsplectrum langs de linker onderhoek en via de linkerzijde van de iPhone naar boven. Snijd daarbij alle lijm door die het scherm aan het frame bevestigt.

    • Steek je plectrum niet dieper dan 3 mm in de opening. Zo voorkom je schade aan de onderdelen in de iPhone.

  11. iPhone X Vervanging van de batterij, Informatie over het scherm: stap 11, afbeelding 1 van 1
    • Er loopt een aantal makkelijk te beschadigen kabels langs de rechterkant van de iPhone. Steek je plectrum daar niet in de opening om te voorkomen dat je je toestel beschadigt.

    Wouldn’t it be better to put this part BEFORE the step where you have to pry open the phone?

    Jan D. Höllwarth - Antwoord

  12. iPhone X Vervanging van de batterij: stap 12, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 12, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 12, afbeelding 3 van 3
    • Steek je openingsplectrum opnieuw in de onderkant van de telefoon en schuif deze nu langs de rechter onderhoek en via de rechterzijkant omhoog om de lijm daar door te snijden.

    • Steek je plectrum ook hier niet dieper dan 3 mm in de opening om te voorkomen dat je de schermkabels beschadigt.

    If you have flat feeler gauges (for adjusting engine valve tappet clearance, ignition points … old school) the .003” thick gauge goes right in. Work your way up in thickness until you can get the pic or supplied pry tool in. Don’t insert metal feeler gauge in too far, just enough to hold crack open. I didn’t need to use the suction cup. I used a hot/cold gel pack heated in microwave to heat edges to soften glue a bit. Made sure it wasn’t so hot I couldn’t stand it on my skin.

    William Olstad - Antwoord

  13. iPhone X Vervanging van de batterij: stap 13, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 13, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 13, afbeelding 3 van 3
    • De bovenkant van het scherm is bevestigd met zowel lijm als klemmen.

    • Schuif je openingsplectrum langs de bovenste hoek van het scherm, terwijl je het scherm voorzichtig naar beneden loopt of trekt, in de richting van de Lightning-poort.

    • Als je te veel kracht gebruikt, zullen de klemmen breken. Wees voorzichtig en heb geduld.

    • Steek je plectrum ook hier niet dieper dan 3 mm in de opening om te voorkomen dat je de voorste sensormodule beschadigt.

    • Schuif je plectrum naar de tegenoverliggende bovenste hoek en snijd alle lijm daartussen door.

    These are the best instructions I’ve ever read for anything.! Thank you!

    Peter Andrew - Antwoord

  14. iPhone X Vervanging van de batterij: stap 14, afbeelding 1 van 1
    • Trek aan het kleine uiteinde van de zuignap om deze van het scherm te verwijderen.

  15. iPhone X Vervanging van de batterij: stap 15, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 15, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 15, afbeelding 3 van 3
    • Open de iPhone door het scherm van links naar rechts open te klappen, alsof je de achterkant van een boek opent.

    • Probeer het scherm nog niet volledig los te krijgen, aangezien deze nog steeds aan het logic board van de iPhone verbonden is met een aantal kwetsbare lintkabels.

    • Zorg dat je, zoals je op de foto kunt zien, het frame inclusief het scherm uit het toestel haalt en voorkom dat het frame in de telefoon blijft hangen.

    • Laat het scherm op een object leunen, zodat je niet te veel spanning op de kabels zet en je nog steeds aan de telefoon kunt werken.

    • Tijdens de hermontage breng je het scherm in positie, op één lijn met de klemmen aan de bovenkant, en druk je de bovenkant van het scherm voorzichtig in de klemmen voordat je de rest van het scherm vastklikt. Als het scherm niet goed vastklikt, controleer je de klemmen om zeker te weten dat ze niet gebogen zijn.

    My phone came apart in a different way and looks not right the little box at the top of the display as actually bolted to the top of the frame body I think something went really wrong when I opened it.

    Mike Kostersitz - Antwoord

    It opens like a book but be careful not to open it all the way — only as far as shown in the photo. Otherwise it will strain the thin cable that connects the sensor module and then no more FaceID for you (or, as it turns out me). This could have been made more explicit in the instructions.

    Richard Tucker - Antwoord

    It opens like a book but be careful not to open it all the way  … the small stainless steel tabs that hold the screen around the metal frame, that are on the bend place (right side of the phone)… are tend to bend, you can straighten them back to 90 deg. but the plastic base that they are on? very fragile- watch out not to break the plastic bezel … it may come apart of the glass.

    dabur872 - Antwoord

    Advice for re-assembly: Before closing up the phone with the seal, check if phone is powering up again and speaker, mic and sensors are still working. If done this check even before installing the board connector bracket in Step 13.

    Alexander Nowak - Antwoord

  16. iPhone X Vervanging van de batterij, Schermmodule: stap 16, afbeelding 1 van 1
    Gereedschap gebruikt in deze stap:
    Magnetic Project Mat
    $19.95
    Koop
    • Verwijder de vijf Y000 schroeven die het beschermpaneel op het logic board bevestigen, met de volgende lengtes:

    • Drie 1.1 mm schroeven

    • Eén 3.1 mm schroef

    • Eén 3.7 mm schroef

    • Zorg dat je, tijdens deze reparatie, bijhoudt welke schroef waarvandaan komt, zodat je deze op de juiste plek weer terug kan schroeven. Zo voorkom je schade aan je iPhone.

    One thing I found helpful for replacing the screws was to use only the 000screwdriver tip, without the handle. This way, the tip isn’t magnetized and the screw doesn’t tend to ‘roll’ off the screwdriver tip (the screw has almost no mass, so the head (largest surface) is pulled around to the side of the screwdriver tip when magnetized).

    Rich May 23, 2020

    ungodly - Antwoord

    My 3.1mm screw had a stripped head, could not remove it. (Factory defect, this iPhone was never opened)

    So I had to give up removing the display assembly, and jumped directly to battery replacement, Step 20.

    That was tricky as I had to keep the display at 90º with a risk of breaking display connectors, but hopefully the replacement went well.

    I would not recommend to do this but to follow the guide, but, in case someone encounters a similar issue, that could help!

    vingu - Antwoord

    My 1.1mm screw had a stripped head. Used a 3mm steel drill to cut the head off (just 1 mm deep haha) so i could remove the bracket.

    Renout - Antwoord

    Be careful on reassembly. Keep the screen supported and not moving. I had difficulty getting the screws in and ended up ruining the screen connectivity at the back of the screen where the ribbon cables go in near the center. I was trying to hand hold the screen and it ended up moving around too much.

    SETH GREEN - Antwoord

    To keep track of the screws, I copy the photos showing their places, then arrange these photos on document in Pages, print it. Next I apply two sided sticky tape (the roll-on type). So all screws have their corresponding places …

    Max Glanzmann - Antwoord

  17. iPhone X Vervanging van de batterij: stap 17, afbeelding 1 van 1
    • Verwijder het paneel.

    • Het kan zijn dat het paneel ietwat vastzit. Til het voorzichtig, maar wel met wat kracht, omhoog om het los te maken.

    • Tijdens de hermontage is dit een goed moment om je iPhone weer aan te zetten om alle functies te testen voordat je de telefoon weer helemaal sluit. Vergeet je telefoon niet weer uit te schakelen als je verdergaat met de reparatie.

    I tested it, then proceeded to close up the device without the bracket. Do I need to reopen and install? All connections are good?

    monastra7 - Antwoord

    The bracket helps those many connectors underneath maintain good contact. Probably in the short term nothing bad will happen, but I’d hang onto the bracket and reinstall it when convenient.

    Jeff Suovanen -

    Agree with Jeff

    cgtyoder -

    I tested all imaginable functionality on the new OLED screen. Taptics are fine. Then, I noticed that the battery wasn't charging. Any ideas as to what could have gone wrong?

    Monica - Antwoord

    for me, the replacement battery was completely dead, small panic when the power-on button was pressed, but quickly realised that this was the situation, and now watching the phone take a power cycle.

    James Stanbridge - Antwoord

    Before clicking the screen assembly back, I tried to test the iPhone by pushing the start button, but nothing happened. After taking off the bracket, reseating the plugs I tried again - nothing happened! Then I plugged in the charging cable connected with the iMac, and it started immediately. So if the phone does not start using the startup button, it might just be a glitch when reconnecting the battery.

    Max Glanzmann - Antwoord

  18. iPhone X Vervanging van de batterij: stap 18, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 18, afbeelding 2 van 2
    • Gebruik de punt van een spudger of een schone vingernagel om de batterijaansluiting uit het contact op het logic board omhoog te duwen.

    • Zorg dat je de zwarte, siliconen afdichtingen rondom deze en andere aansluitingen niet beschadigt. Deze afdichtingen zorgen voor extra bescherming tegen water en stof.

    • Zorg dat je de aansluiting wegbuigt van het logic board om zo te voorkomen dat deze tijdens de reparatie per ongeluk contact maakt met het contact en zo de telefoon mogelijk aanzet.

    cosa può succedere se non si disconnette la scheda logica'?

    luca.valli - Antwoord

    note: be careful not to crush or puncture your battery at this step!! I gave mine a minor dent, which I hope wont be a problem.. but something to keep in mind for fxlks in the future!

    Noal Balint - Antwoord

    Thanks, already did it)

    Stephen Hedrick -

  19. iPhone X Vervanging van de batterij: stap 19, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 19, afbeelding 2 van 2
    • Gebruik de punt van een spudger of een vingernagel om de aansluiting van de sensormodule in het voorste paneel omhoog te duwen en te ontkoppelen.

  20. iPhone X Vervanging van de batterij: stap 20, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 20, afbeelding 2 van 2
    • Gebruik de punt van een spudger of een vingernagel om de aansluiting van de OLED-schermkabel los te koppelen.

    • Om drukaansluitingen zoals deze weer aan te sluiten, positioneer je deze totdat op z'n plek lijkt te zitten en duw je één kant van de aansluiting omlaag tot deze vastklikt, om vervolgens hetzelfde te doen aan de andere kant. Druk niet op het midden, want als de aansluiting verkeerd zit, zul je de pinnen buigen en zo schade veroorzaken.

    Snap ‘em in like little Legos.

    Ray Johnson - Antwoord

    Maybe the manual should flip step 17 and 18 (as the digitizer cable from 18, is in the way of the OLED cable of step 17) ?

    Renout - Antwoord

  21. iPhone X Vervanging van de batterij: stap 21, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 21, afbeelding 2 van 2
    • Gebruik de punt van een spudger om de aansluiting van de digitizerkabel uit het contact omhoog te duwen.

    • De inkeping waar deze aansluiting in zit, bemoeilijkt het opnieuw aansluiten van deze kabel. Neem je tijd en positioneer het met zorg, om het dan voorzichtig op z'n plek te drukken met het topje van je vinger—eerste de ene kant, dan de andere kant. Als het goed is, voel je het wanneer de aansluiting vastklikt.

    • Als er een deel van je scherm niet op aanraking reageert na de reparatie, ontkoppel je de batterij en sluit je deze aansluiting opnieuw aan. Zorg hierbij dat deze volledig op z'n plaats klikt en dat er geen stof of andere dingen in het contact zitten.

    This was probably the hardest part other than trying to get the screen off with the crappy suction cups. I re-installed the bracket only the find out that the touch screen would not respond to touch. Had to remove the five screws, remove the bracket and reseat the recessed screen connector. Reseating the bracket took another 10+ minutes. I carefully used the angled forceps to grab the cable and align the connector being careful not to damage the cable.

    Once you have the connector seated, I would reconnect the battery, power on the phone, and check the touch screen response before re-installing the bracket (step 13).

    Tawan Khamapirad - Antwoord

    Yeah, this was probably the trickiest part of the reassembly. The power connector cable kept getting in the way so I moved it carefully but fully out of the way. Then it was a matter of fiddling around with it a bit and being careful not to force it on.

    Jeffrey Hoy -

    I was positive that I had messed something up, I had powered up the phone to test three different times and everything seemed find except there was no touch at all. On my fourth attempt, I carefully examined everything for dust and debris (blowing gently), and I did notice that a corner of the connector (more like part of the ribbon) was bent slightly, and I straightened it. I don't know if it was the ribbon or some tiny debris, but after reseating a fourth time, it worked.

    Pol Llovet - Antwoord

    Very important part of the tutorial. Be careful and patience! In my case the screen and camera didn't respond after assemble, so I tried again to reconnect the connector like tutorial said and it worked well. Now my iPhone feel like a new one 💪🏼

    Efrain Maestre - Antwoord

  22. iPhone X Vervanging van de batterij: stap 22, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 22, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 22, afbeelding 3 van 3
    • De flexkabel van de sensormodule in het voorste paneel zit lichtjes vast op z'n plek.

    • Til de kabel voorzichtig omhoog totdat deze loskomt van de lijm eronder.

    Do this sensor affect face id?

    bonglkv - Antwoord

    It is part of the face id part so yes. This is the ear piece too so if the ribbon tears there is a chance the ear piece will stop working as well.

    Stephen Patterson - Antwoord

    Be super careful handling this ribbon particularly. I did a battery install and, when I was done, I had a phone with a new battery and no Face ID. That’s a $300 Apple repair, and no 3rd party shop will touch it. I believe the ribbon lays vertically (i.e., perpendicular to the “floor” of the phone, against the side edge of the battery. During the re-install, I must have forced the ribbon into position after seating the connector, causing fatal flexing of the ribbon. (Don’t know this for sure, but I see another comment saying that this cable is part of Face ID.) Anyway, bottom line: BE CAREFUL REMOVING AND REINSTALLING THIS RIBBON!

    Jonathan Pines - Antwoord

    My flex cable was more than lightly adhered in place. I needed to use a guitar pic or similar to help encourage adhesive to separate. I wouldn’t pull too hard like shown in pictures unless you had just the right grip on the ribbon cable so as to avoid damaging flex cable. See note above (5/31/20)

    William Olstad - Antwoord

    Bizarre — it turns out my whole front panel sensor assembly came entire off of the front screen and is stuck to the logic board.

    Karl Jarvis - Antwoord

    I also found the glue quite recluctant to release so I applied a second or two of heat using the wife's hair dryer which softened it and the cable lifted much easier then. Be careful not to apply too much heat though which could then impact other internal components.

    LosBenitos - Antwoord

    Cho ít cồn 90° vào để mềm keo dễ tháo

    huuhaukimngan - Antwoord

    my iphone x doesn't have a front panel sensor? in fact, it looks completely different than the picture???

    Kenneth McLeod - Antwoord

    @kennethmcleod, most likely you've separated the screen frame from the screen itself. We see this most commonly when people neglect to remove the pentalobe screws next to the charging port. Usually the cure is to take out those screws, then repeat the screen removal process on the frame that's still attached to the phone.

    Jerry Wheeler -

    You don't need to disconnect the front sensor to change the screen. Just leave it connected and remove from the screen side.

    Anthony Boshell - Antwoord

  23. iPhone X Vervanging van de batterij: stap 23, afbeelding 1 van 1

    I tried this and broke the cable can it still repair

    Alexis Rodriguez - Antwoord

    At this point I would have found it easier to remove the glue from the edges than later on when I was reassembling it. I bought the kit that had the replacement glue in it.

    Grant - Antwoord

    Excellent guide! Would love to have a link to moving the sensor assembly from the old display to the new here.

    Nicole - Antwoord

    CAUTION:

    Removing the Taptic Engine or Speaker in next step is optional and the guide continues as this was per se needed.

    Unnecessary work and also If you remove the speaker you lose the adhesive gasket and this is not included in the scope of delivery of the "Battery replacement" offering.

    So do not remove and avoid losing waterproofing.

    Julian Gonzalez - Antwoord

  24. iPhone X Vervanging van de batterij, Onderste speaker: stap 24, afbeelding 1 van 2 iPhone X Vervanging van de batterij, Onderste speaker: stap 24, afbeelding 2 van 2
    • Zorg dat je de drie rijen met 'grounding pads' aan de onderkant van de iPhone niet aanraakt.

    • Verwijder de zeven schroeven die het paneel onder de trilmotor en de speaker bevestigen:

    • Twee Y000 1.9 mm schroeven

    • Eén Y000 1.2 mm schroef

    • Eén Y000 1.6 mm schroef

    • Eén Phillips 2.4 mm schroef

    • Eén Phillips 1.7 mm schroef

    • Eén Phillips 1.5 mm schroef

    For battery replacement:

    It is not necessary to remove Taptic Engine and speaker to replace a battery. Go straight to the step #33

    Additional video: https://youtu.be/2GfBOlJEW10

    Alexander - Antwoord

    I wish I seen this before I did all that! Thank you for that information. Next time I do something like this. I'm gonna pay more attention to the comments.

    Eric Marino -

    Removing the Taptic Engine and speaker greatly improves your chances of getting the battery adhesive strips out intact. If those break, you’ll have a much tougher time.

    Jeff Suovanen -

    Boy, I tried to skip removing these items but was unable to get the glue strips out with them in place, not much to grab and tabs were kind of stuck to a seam in the battery, and hard to tell the difference between the seam and the strip tabs. For me I had to remove these items to get this done.

    marshallburchard -

    I stopped removing things after getting the display side off. There were 3 screws stripped on the speaker cover which wouldn't come out so I punted. Just pried the battery out with a smudger tool and some patience, starting at the top and working towards the bottom. New battery is in and working fine.

    Andy Price - Antwoord

    The 2.4mm screw identified as “green” needs a Y000 screwdriver

    seb6po - Antwoord

    Thanks for not removing the following steps. this made me break the connector for the bottom speakers >:(

    Andrew Romano - Antwoord

    The color codes are missing from my display — only on this step.

    nat2 - Antwoord

    The screws color and quantities in list don’t match the schematic ! I wish i had a magnetic screw mat before starting, because not only i removed the Taptic Engine and speaker unnecessarily, but i also lost a screw ?

    fb.mailing.lists - Antwoord

    For first timer, dont think its possible to skip these steps and remove battery. It’s hard to remove the glue

    Wex - Antwoord

    Does anyone know the purpose of this bracket "with grounding pads"? What would be the possible side effects if it was damaged or not connected properly during reassembly?

    Anne Aunyme - Antwoord

    I had to remove the tactic and speaker could not get the glue strips out so glad the steps to do so were in this guide.

    P Bond - Antwoord

    Sure would like to know WHY the warning "Be careful not to touch the three rows of grounding pads..." What would or could happen if I did touch them??

    Chad Gagnon - Antwoord

    Removing the battery strips is a major PITA, just skip this step and everything onwards, remove the one strip on the top part of the battery (according to step 33) and for the bottom part of the battery, pry it off with a plastic spudger.

    Yes, this is not the elegant solution, but the quickest and easiest one. This method is better, as you don't want to keep the old battery anyway, so why bother. (You must not puncture the battery though! But as long as you're only working with a plastic tool and are careful, nothing can happen from my experience.)

    speaker gasket - Antwoord

  25. iPhone X Vervanging van de batterij: stap 25, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 25, afbeelding 2 van 2
    • Til het paneel op vanaf de kant die het dichtst bij de batterij ligt. Probeer deze nog niet volledig te verwijderen aangezien deze nog steeds vastzit met een kleine flexkabel.

  26. iPhone X Vervanging van de batterij: stap 26, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 26, afbeelding 2 van 2
    • Gebruik, terwijl je het paneel uit de weg houdt, de punt van een spudger om de flexkabel eronder omhoog te duwen en los te koppelen.

  27. iPhone X Vervanging van de batterij: stap 27, afbeelding 1 van 1
    • Verwijder het paneel.

    My bracket was in two pieces.

    Jim Steward - Antwoord

  28. iPhone X Vervanging van de batterij: stap 28, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 28, afbeelding 2 van 2
    • Verwijder de 2.1 mm Y000 schroeven die het plaatje op de speakeraansluiting bevestigt.

    L'unique vis non?

    Easy Repair - Antwoord

    Effectivement ;-) Merci pour les bons yeux et la remarque !

    Claire Miesch -

  29. iPhone X Vervanging van de batterij: stap 29, afbeelding 1 van 1
    • Verwijder het beschermplaatje bovenop de speakeraansluiting.

  30. iPhone X Vervanging van de batterij: stap 30, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 30, afbeelding 2 van 2
    • Gebruik de punt van een spudger om de speakeraansluiting omhoog te duwen en los te koppelen.

    As mentioned in a comment by timblake2112 (see step 29), this step is not necessary and can be skipped skipped. I would advise you to do so, as removing your speaker is guaranteed to ruin your gasket and rubber seal. This will result in loss of water resistancy of your iPhone and could potentially harm the sound quality of your speaker.

    Try removing the Taptic Engine without removing the speaker. It might still be possible removing the battery adhesive strips and your speaker will stay in its original condition.

    speaker gasket - Antwoord

  31. iPhone X Vervanging van de batterij: stap 31, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 31, afbeelding 2 van 2
    • Wees, bij het omhoogduwen van de speaker, voorzichtig dat je de flexkabel die je zojuist hebt losgekoppeld, niet beschadigt. Indien nodig kun je deze naar een zijde wegduwen, zodat je ruimte maakt voor de speaker om eruit te komen.

    • Steek een spudger onder de bovenkant van de speaker dichtbij de zijkant van de behuizing van de iPhone.

    • Duw en til de bovenkant van de speaker voorzichtig omhoog.

    • Check, bij het herinstalleren van de speaker, de positie van de flexkabel en zorg dat deze niet vast of klem komt te zitten onder de speaker.

  32. iPhone X Vervanging van de batterij: stap 32, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 32, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 32, afbeelding 3 van 3
    • Pak de speaker vast bij de zijkanten en wiebel deze heen en weer, zodat deze langzaam loskomt van de lijm die het aan de onderkant van de iPhone bevestigt.

    • Trek de speaker weg van de onderkant van de iPhone totdat deze loskomt van de gelijmde pakking.

    As mentioned in a comment by timblake2112 (see step 29), this step is not necessary and can be skipped skipped. I would advise you to do so, as removing your speaker is guaranteed to ruin your gasket and rubber seal. This will result in loss of water resistancy of your iPhone and could potentially harm the sound quality of your speaker.

    Try removing the Taptic Engine without removing the speaker. It might still be possible removing the battery adhesive strips and your speaker will stay in its original condition.

    speaker gasket - Antwoord

  33. iPhone X Vervanging van de batterij: stap 33, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 33, afbeelding 2 van 2
    • Verwijder de speaker.

    • De gelijmde pakking van de speaker is niet herbruikbaar. Schraap alle lijmresten weg met behulp van een pincet.

    • Om te zorgen dat je telefoon beschermd blijft tegen water- en stofschade, is het handig om tijdens de remontage de afdichting te vervangen. Maak de plek schoon met wat isopropyl alcohol en een stuk stofvrij doek of een koffiefilter om ervoor te zorgen dat de afdichting goed kan hechten. Breng een nieuwe afdichting aan op de speaker en installeer dan pas de speaker.

    You don’t need to remove the speaker and ruin its gasket. You can wiggle and slide the taptic engine out without removing the speaker. I’ve done this twice on rear shell replacement jobs.

    timblake2112 - Antwoord

    Maybe I'm a bit daft, but where's the instruction just how to line up the speaker gasket when replacing? I only have one so I'd like to avoid wrecking it. And I completely cleaned off the old one in order to do a good job of things. Why no simple instruction from part supply link?

    MrRoundel - Antwoord

  34. iPhone X Vervanging van de batterij, Trilmotor: stap 34, afbeelding 1 van 2 iPhone X Vervanging van de batterij, Trilmotor: stap 34, afbeelding 2 van 2
    • Verwijder de 2.3 mm Phillips schroef die de trilmotor bevestigt.

  35. iPhone X Vervanging van de batterij: stap 35, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 35, afbeelding 2 van 2
    • Gebruik een spudger om de flexkabel van de trilmotor los te koppelen door deze in een rechte beweging uit het contact omhoog te duwen.

  36. iPhone X Vervanging van de batterij: stap 36, afbeelding 1 van 1
    • Verwijder de trilmotor.

  37. iPhone X Vervanging van de batterij, Batterij: stap 37, afbeelding 1 van 1
    • De batterij van de iPhone X is vastgemaakt aan de achterste behuizing door middel van vier kleefstrips met treklipjes—één onder de bovenste batterijcel en drie onder de onderste batterijcel.

    • Iedere kleefstrip heeft een zwarte treklip aan het einde welke lichtjes vastzit aan de zijkant van de batterij.

  38. iPhone X Vervanging van de batterij: stap 38, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 38, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 38, afbeelding 3 van 3
    • Scheid de eerste kleefstrip onder de batterij van de onderkant van de batterij.

    • Ieder treklipje heeft een klein gat in het midden; steek een tool door het gat als je moeite hebt om het treklipje vast te pakken.

    • Zorg er wel voor dat je de batterij niet steekt met scherpe voorwerpen. Een doorboorde of beschadigde batterij kan gevaarlijke chemicaliën lekker of in brand vliegen.

    hole breaks instantly on pulling. adhesive tab does not release from side of battery

    Dominick garton - Antwoord

    I had a lot of trouble with this. Only two came out properly and the others snapped off. I heated up the back of the phone with a hair dryer then used the flat end of the spudger to slowly pry it off right to left, bottom to top.

    Grant - Antwoord

    just pry it off, why bother

    speaker gasket - Antwoord

  39. iPhone X Vervanging van de batterij: stap 39, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 39, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 39, afbeelding 3 van 3
    • Herhaal de stap hiervoor om de resterende twee kleefstrips aan de onderkant van de batterij los te maken.

    • Zorg dat je de speakerkabelaansluiting, onder de middelste kleefstrip, niet beschadigt.

  40. iPhone X Vervanging van de batterij: stap 40, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 40, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 40, afbeelding 3 van 3
    • In de volgende stappen zul je aan ieder lipje trekken om zo de kleefstrips onder de batterij uit te rekken. De kleefstrips laten door het uitrekken uiteindelijk los en zorgen ervoor dat de batterij makkelijker uit de telefoon te verwijderen is.

    • Als de strips breken, geen paniek! Ze werken niet altijd zoals het hoort. Lees verder voor wat extra tips voor het verwijderen van afgebroken strips.

    • Om je kans van slagen te vergroten:

    • Zet geen extra druk op de batterij. Zorg dat je de iPhone aan de zijkanten vast hebt.

    • Houd de strips plat en vlak terwijl je trekt.

    • Trek zo langzaam mogelijk, zodat je de strips de tijd geeft om uit te rekken en los te komen. Het duurt ongeveer 15-30 seconden voordat de strips zijn uitgerekt en loskomen.

    • Trek in een zo laag mogelijke hoek aan de lipjes, zodat je zeker weet dat de strips niet scheuren op de zijkant van de batterij.

    • Als één van de strips wel afbreekt terwijl deze nog onder de batterij vastzit en niet kan worden verwijderd, ga je gewoon verder met de andere strips en de hierna volgende stappen.

  41. iPhone X Vervanging van de batterij: stap 41, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 41, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 41, afbeelding 3 van 3
    • Pak één van de buitenste kleefstrips onder de batterij vast en trek deze langzaam weg van de batterij, in de richting van de onderkant van je iPhone.

    • Trek met een constante kracht zodat er steeds spanning op de strip staat, totdat deze tussen de batterij en de achterkant van het frame wegschiet.

    • De kleefstrip zal een stuk langer worden — meerdere keren z'n eigen lengte. Blijf trekken en herpak de strip dichter bij de batterij als dat nodig is.

    • Als de kleefstrips tijdens het verwijderingsproces breken, kun je je vingers of een pincet gebruiken om de overgebleven lengte van de strip te pakken te krijgen om hieraan te kunnen trekken.

    • Als één van de strips breekt en niet meer kan worden gepakt, ga je gewoon verder met de overige kleefstrips en daarna met de volgende stappen.

    I found it easier to grab the end of the adhesive strip sideways with narrow tweezers, "twirl " the tweezers to wrap the strip around them a few times, then gently pull the strip with the tweezers.

    punkinann - Antwoord

  42. iPhone X Vervanging van de batterij: stap 42, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 42, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 42, afbeelding 3 van 3
    • Herhaal de vorige stap om de kleefstrip aan de overkant los te maken en laat de middelste van de drie onderste kleefstrips zitten om als laatste los te trekken.

  43. iPhone X Vervanging van de batterij: stap 43, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 43, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 43, afbeelding 3 van 3
    • Verwijder de middelste kleefstrip. Wees voorzichtig dat je deze niet breekt op de flexkabel van de speaker.

  44. iPhone X Vervanging van de batterij: stap 44, afbeelding 1 van 2 iPhone X Vervanging van de batterij: stap 44, afbeelding 2 van 2
    • De laatste kleefstrip licht erg dicht bij de hardware van de Face ID. Als deze beschadigd raakt, kan dit enkel worden gerepareerd door Apple, dus wees extra voorzichtig.

    • Peuter het laatste treklipje, aan de bovenkant van de bovenste batterijcel, los en scheid deze van de batterij.

    surtout ne pas passer avec la spatule par le bas, vous risqueriez d arracher la nappe du volume et du nfc,

    Ludovic Klein - Antwoord

  45. iPhone X Vervanging van de batterij: stap 45, afbeelding 1 van 3 iPhone X Vervanging van de batterij: stap 45, afbeelding 2 van 3 iPhone X Vervanging van de batterij: stap 45, afbeelding 3 van 3
    • Trek en verwijder de laatste kleefstrip.

    • Als je de laatste kleefstrip lostrekt, kan het zijn dat je de batterij meetrekt, dus zorg dat je deze vasthoudt zodat deze niet wegvliegt—maar druk niet op de batterij zelf aangezien deze druk ervoor kan zorgen dat de kleefstrip eronder breekt.

    • Als je alle kleefstrips succesvol hebt weten te verwijderen, kun je de volgende stap overslaan.

    • Als één van de kleefstrips onder de batterij is afgebroken en deze niet meer vast te pakken is, kun je wat druppels isopropyl alcohol (>90%) onder de batterij toedienen aan de kant waar de kapotte kleefstrip zich bevindt.

    • Wacht ongeveer een minuutje, zodat de alcohol in kan trekken en de lijm kan verzwakken. Gebruik het platte einde van je spudger om de batterij op voorzichtige wijze omhoog te tillen.

    • Probeer de batterij er niet geforceerd uit te wrikken. Indien nodig kun je ervoor kiezen om nog wat extra druppels isopropyl alcohol toe te dienen om de lijm te verzwakken. Voorkom dat de batterij vervormt of beschadigd raakt door je tool.

    • Wees voorzichtig en zorg ervoor dat je noch de lintkabel noch de draadloze oplaadspoel direct onder de batterij beschadigt.

    • Als je meer wilt weten over alternatieve methoden om de batterij uit de behuizing te verwijderen, ga je verder met de volgende stap.

  46. iPhone X Vervanging van de batterij, Alternatieve methode om de batterij uit de behuizing te verwijderen: stap 46, afbeelding 1 van 2 iPhone X Vervanging van de batterij, Alternatieve methode om de batterij uit de behuizing te verwijderen: stap 46, afbeelding 2 van 2
    • Als één van de kleefstrips is afgebroken en de batterij nog steeds aan de achterkant van het frame vastgeplakt zit, prepareer je een iOpener of gebruik je een föhn om de achterkant, direct achter de batterij, te verwarmen.

    • Verwarm de iPhone totdat de achterste behuizing net iets te heet is om comfortabel aan te raken, maar maak het niet heter aangezien je de batterij hiermee kan ontsteken.

    • Draai de iPhone weer om en rijg een sterk stuk dun draad (zoals flosdraad of een stuk van een dunne gitaarsnaar) onder de batterij door.

    • Draag handschoenen om je vingers je beschermen of wikkel ieder eind van het stuk draad om een tool die fijner vast te houden is.

    • Trek het stuk draad van links naar rechts in een zagende beweging over de gehele lengte van de batterij om zo de kleefstrip los te krijgen. Dit kan even duren, aangezien de kleefstrip langzaam loskomt, maar met wat geduld moet dit lukken. Zorg dat je de batterij niet vervormt of beschadigt.

    • Als je ervoor kiest om de batterij uit de iPhone te wrikken, wees dan extreem voorzichtig aangezien je met gemak de lintkabels of de draadloze oplaadspoel direct onder de batterij kan beschadigen.

    if you use a guitar string, remember NOT to use a METALLIC guitar string.

    Ross King - Antwoord

    flexible plastic rules with alcohol work too

    Wex - Antwoord

    I can confirm that IPA (Iso Propyl Alcohol) and, in my case, the plastic plectra in any iFixit kit worked a treat.

    P Bond -

  47. iPhone X Vervanging van de batterij: stap 47, afbeelding 1 van 1
    • Pak de batterij aan de onderkant vast en verwijder deze uit je iPhone.

    • Zorg dat je alle alcoholresten in de telefoon verwijdert door deze voorzichtig weg te vegen of door deze te laten drogen voordat je je nieuwe batterij installeert.

    • Herinstalleer de trilmotor en de speaker voordat je de nieuwe batterij installeert. Dit zorgt ervoor dat je nieuwe batterij makkelijker correct te positioneren is bij het installeren.

    • Zorg dat je, voordat je je nieuwe batterij bevestigt, eerst de batterijaansluiting weer tijdelijk op het contact op het logic board aansluit. Dit helpt bij het op de juiste plek plaatsen van de batterij.

    • Bevestig je nieuwe batterij, koppel deze weer los van het logic board en ga verder met het in elkaar zetten van je toestel.

    • Als je nieuwe batterij niet wordt geleverd met vooraf geïnstalleerde kleefstrips, kun je deze handleiding gebruiken om de kleefstrips te vervangen.

    • Voer een geforceerde herstart uit na het weer in elkaar zetten van je telefoon. Dit kan een aantal problemen voorkomen en eventuele probleemoplossing makkelijker maken.

    When reinstalling the battery, the Taptic Engine does serve as a useful way to orient the battery, but it should also be noted that if you push right up against that as you install the battery (as I did) and don’t pay any attention to power connector (shown in step 14), there is a risk that the connector from the battery will not line exactly with the connector port on the board. Mine was only off a mm so I had to get a little creative to try to get it to stretch to reach and connect to the port on the board. Just keep that in mind as you place the battery (with adhesive) down.

    Jesse Bolane - Antwoord

    Connect the battery first then put it in place. Other way it is hard to adjust power connector.

    Alexander - Antwoord

    I would also HIGHLY suggest re-installing the speaker as well before installing the battery - it was a very tight squeeze as the bottom-right of the battery was snug against the speaker when I tried to get that back in.

    cgtyoder - Antwoord

Conclusie

Vergelijk je vervangende onderdeel met het originele onderdeel — het kan zijn dat je meerdere onderdelen mee over moet zetten of beschermlagen voor de lijm moet verwijderen voordat je het nieuwe onderdeel kunt installeren.

Om je toestel weer in elkaar te zetten, volg je deze instructies in omgekeerde volgorde.

Breng je e-afval naar een R2 of e-Stewards gecertificeerde recycler.

Ging je reparatie niet zoals gepland? Check dan onze Antwoordencommunity voor hulp bij het oplossen van je probleem.

391 andere personen hebben deze handleiding voltooid.

Met dank aan deze vertalers:

en nl

100%

Thomas Keulemans helpt ons de wereld te herstellen! Wil je bijdragen?
Begin met vertalen ›

Jeff Suovanen

Lid sinds: 08/06/13

427.144 Reputatie

259 handleidingen geschreven

Team

iFixit Lid van iFixit

Staff

136 Leden

16.579 handleidingen geschreven

51 opmerkingen

In the store it says the iSlack is only for iPhone 5 and 6. In this review the iSlack is used (without tray). Does that mean it can be used on the iPhone X as well?

Ronald van der Meer - Antwoord

@rvdm The little bracket in the middle of the iSclack is sized for iPhone 5, but that bracket is optional and very easy to detach. At that point you have a really great general-purpose suction tool that works for all kinds of devices (even bigger ones like tablets). I’ll see about updating the description on the store page to reflect that fact. ;)

Jeff Suovanen -

Have you all ever had a problem of the phone staying stuck on a percentage and takes so long to charge plz let me know because I just got my iPhone X and it take so long to charge and I got it brand new from AT&T

Cristan Montes - Antwoord

Esta solucionado el tema del Chip Texas instrument para baterias no reemplazadas en Apple, gracias.

FELIX MARQUEZ - Antwoord

¿A qué te refieres con eso?

Tomas -

C’è un errore di traduzione al passo 33 BATTERIA , iphone X diventa iphone 8.

Marco

Marco Pautasso - Antwoord

Ciao Marco! Hai occhi di lince! Grazie per il commento. Ho corretto la traduzione. Commenti di questo tipo sono sempre benvenuti. Hai anche la possibilità di adattare direttamente la traduzione, cliccando sull’icona “Traduci”. Saluti, Claire

Claire Miesch -

Note that my replacement battery was completely dead when I installed it, so when I tested it, I thought perhaps something wasn’t hooked up right. After removing the bracket for the connectors and reattaching the battery connector I tried again. Since that failed, I plugged the phone in. I got a “no charge” battery icon. After a few minutes I removed the phone from the charger. The phone stayed on with the “plug in the phone” icon, so I knew everything was put back together correctly.

Jon12 - Antwoord

Critical Note! When installing the new battery make sure the connector lines up. The instructions mention having the speaker and taptic engine in place so I focused on squaring up with those. This was a mistake! Now my connector is 2mm too low and won’t line up. Not sure how I will fix this yet but hopefully I won't need to remove everything again.

Christopher Jones - Antwoord

Where can I buy a genuine original iPhone X battery as amazon Walmart sells fake batteries

masrin - Antwoord

You can not buy a genuine battery.

Alexander -

How to make out a genuine original battery from a fake one sold all over the globe?

masrin - Antwoord

Super Set, auch toll das hier die Dichtung dabei ist. Akku lädt und zeit die %-Werte an. Beim nächsten Mal kauf Ichs gleich hier"! War jetzt schon die 2te Reparatur. Mittlerweile schaff ich das schon ca. 40 min ;)

Danke

Peter - Antwoord

Aparecerá el porcentaje de la batería en el apartado de “salud”?

Gustavo González Martínez - Antwoord

removing the components that are below the battery seems rather unnecessary to me, you could remove the battery without taking those out

Samuel Casas - Antwoord

I had an issue with a swollen battery on a iphone X, the battery was pushing the display assembly and the phone couldn’t close properly. Replaced with new battery and all went fine. Great guide as always

Georgi Ivanov - Antwoord

This battery already comes with battery health indicator or need to reprogram the battery ?

danial nabil - Antwoord

Big thank you for introduction!

commaai - Antwoord

It would be nice if this addressed the waterproof adhesive, mentioned in Step 6. Doesn’t pulling the phone apart make it no longer watertight?

Winston - Antwoord

Instructions for replacing the adhesive seals are linked in the guide (Step 19). I wouldn’t count on your phone being waterproof after a repair, but a phone from 2017-2018 likely won’t be particularly water-resistant anymore, anyway. Those seals tend to degrade over time.

Jeff Suovanen -

Hi, I bought the battery from you and installed it exactly like your steps.

But after two days of use, a message appears to me that this battery is not original and its percentage cannot be read !!!

What to do now ???

Fahad Mohammad Fahad - Antwoord

When changing the battery to a third party one, are there any notifications that appear such as “not a genuine battery” and does reprogramming the battery help prevent this.

Farjad Akram - Antwoord

BE WARNED! THE IPHONE’S OUTSIDE IS VERY, VERY SHARP! I escaped with 4 cuts on my fingers.

AemVR - Antwoord

I replaced two of these in one night. The first one worked great but the second’s OLED screen won’t come on. The phone is on because I can hear it charge when I plug it in, but for some reason the screen is dead.

Lucas - Antwoord

If you’re buying the battery from iFixit I strongly suggest getting the full kit and not the battery-only option so that you get the glue and the gasket. Great guide, thank you!

Grant - Antwoord

It is perfectly possible to do the replacement without removing anything other than the bracket and the battery connector.

This reduces the number of steps to about 10 and takes about 15 minutes.

Neil Roberts - Antwoord

Awesome guide! I finished it, and now I have a fully working X

Just one thing: the video and the instructions differ on step 20, making the rest unnecessary according to the video guide. On the other hand, it may facilitate taking the glue off, especially for newbies.

Ed Oliver - Antwoord

I don’t want to sound like “that guy,” but the cost of a battery replacement is only $69 at an Apple Store. This DIY solution, which can go t!ts up anywhere along the 43 steps, requires the purchase of parts that cost almost as much as just letting Apple do it. I love fixing/replacing/upgrading my hardware as much as the next guy, but this seems like a scenario where the majority of people would be better off visiting an Apple Store.

koelpien - Antwoord

Except that authorized stores won’t replace a swollen battery, and neither will Apple. Otherwise yes, if the few hours extra and a few 10s of dollars is the additional price for a turnkey solution, most folks are better off having the work done for them.

Mike Hocker -

Was suffering from a hugely swollen battery so it made removing the adhesive pretty difficult (and I was being super careful since the battery had swollen so much). The “stretch and pull” with the adhesive was a no-go and I was hesitant to heat the phone. I ended up slowly pulling up on the battery at the top and gently working the adhesive away. It took some time, but worked out.

Great guide, as usual!

Patrick C - Antwoord

Jeg har lige skiftet batteri på min iPhone X i starten kunne jeg kun oplade trådløst, men nu kan jeg slet ikke oplade Den reagerer slet ikke på noget mere den er helt død Hvad kan jeg gøre ???

enok - Antwoord

The adhesive under the original battery broke. ALL TABS RIPPED APART! I have no floss nor metal guitar string. Help please. This is my only mobile phone. I need it 24/7.

vmm - Antwoord

Commentary on swelled batteries: don’t tell Apple, they will mark your iPhone SerialNumber in their database as not repairable and you will never be able to get a battery replacement in the future (per Apple phone support, as we tried to get their swollen battery replaced by appointment). We are not happy campers, now I need to use up valuable time replacing the battery. At least replacing the battery is an option with the help of iFixit. (oh, and they won’t put in a new battery if I remove the old one either— although once the old one is removed the hardest part of the work is done)

Mike Hocker - Antwoord

Wasn’t too bad, except some of the screws that need to be removed are tiny and I found out that my eyes are not the best anymore ?.

jabuka - Antwoord

Many thanks for this great tutorial !! Just changed the battery of my 4 years old iPhone X, I’m very happy to have a fresh one inside !

Faabio - Antwoord

Hello,

I have an iPhone X Model number MQAF2LZ/A bought in Perú and once I started removing the display I noticed it doesn’t open like in the pictures or video here. There is a connector behind the ear piece that connects to the main board and I can’t open it. I see if I force it I will break this connector. Have somebody worked with this model? and recommend where to buy a replacement display? The one I bought is for model number MQAF2LL/A (USA). (the ribbon cables look different)

John W - Antwoord

Today I show you how to replace the battery of the Iphone X. We need one screwdriver, one suction cup, 1 iopener, 1 pair of tweezers, 1 plastic pry tool, and 1 spudger.  Remember to turn off the power. The replacement can cause the loss of water resistance. To replace the battery for iphone X, do the following steps. Step 1, use the screwdrive to remove the screws at the bottom. Use Iopener to soften the adhesive. Clip the suction cup onto the screen and use a pry tool to pry out the screen. Lift up the screen 90 degrees on the right. Take off the small screws holding the battery cable and the motherboard. Next, use the tweezers to lift up the metal bracket. Use a spudger to pry away the battery connector and 3 display connectors. Use tweezers to remove the battery stripe. Remove the old battery. Reverse the above steps to install the new battery.

Hội Nguyễn - Antwoord

This takes me like 2 mins no tools required and I reused the adhesives also so less waste . I dont pull anything or use tools bar a tri star….. Should be updated . Soak in alcohol slightly leave for 2 mins remove battery , dry and replace using old adhesive (which is perfect) no cleaning ….Digithaiz

Sam Barton - Antwoord

Jeez I dont mind even making you a guide for this as its mostly sit and wait for all of the 5 mins max this takes!

Sam Barton - Antwoord

Porcentaje de la Condición de la batería funcionará bien?

Inksane BēLCK - Antwoord

Misma pregunta.

Tomas -

Hallo,

ich habe mein iphone x display und batterie ausgetauscht, allerdings bekomme ich die fehlermeldung

Apple erfasst die Hardwarekennungen Ihres iPhones, um unsere Dienste zu identifizieren und zu aktivieren.

İch habe mein iphone x damals in der türkei gekauft und leider komme ich nach weiter woran kann das liegen ?

mst Ozyn - Antwoord

Excellent guide! Took about1,5 - 2 hours too including trying to remove all of that black sticky stuff! :) Should have bought some isopropanol... Aligning and fixing the new sealing was a bit tricky! Really had to think for a while which layer of plastic to remove first...

No problem removing the adhesive under the battery which never has worked on older iphones! pehww.... :)

Thomas Lundström - Antwoord

Worked great. Only putting the display adhesive on was difficult. I am thinking about fixing the broken display now, because it maked so much fun!

Mike Stanke - Antwoord

Personnellement je n’ai pas démonté les haut parleur et le bas de l’iPhone … j’ai directement chauffé à l’arrière et décollé la batterie …. Plus rapide et moins dangereux pour le reste

Dark Stig - Antwoord

I don't know if it's common knowledge, but I just flashed on what the first sign of my battery expanding was. I used an Otterbox Defender case on my iPhone X. 3-6 months before the battery made its expansion obvious, the volume buttons started not working well. I thought it was the Otterbox. But now that I've replaced the battery the volume buttons are working fine. Somehow the battery was distorting the physical interface between the phone buttons and the case buttons. By the time I noticed the battery inflating, it had pushed up the display screen away from its frame. Apparently the battery was getting rather dangerous for possible setting itself ablaze.

MrRoundel - Antwoord

0% Remaining cómo solucionar ??

Ernesto Salazar - Antwoord

I replaced my battery just fine but now my screen is wonky. I’m getting yellow and black lines and it’s not working properly. I reattached everything twice but still no luck. Any body have the same issues or a fix? My screen was perfect before changing out my battery.

Jeremy - Antwoord

This battery has to be reprogrammed to work with the health condition battery?

Tomas - Antwoord

Thanks so much - this is exactly what I needed :)

Molly Floyd - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 214

Afgelopen 7 dagen: 1,263

Afgelopen 30 dagen: 5,846

Altijd: 776,407