Ga door naar hoofdinhoud

iPhone 7 Vervanging van de aan-/uitknop

Wat je nodig hebt

  1. iPhone 7 Vervanging van de aan-/uitknop, Pentalobe schroeven: stap 1, afbeelding 1 van 1
    • Ontlaad je iPhone, voordat je begint, tot onder de 25%. Een geladen lithium-ion batterij kan in brand vliegen en/of exploderen als deze per ongeluk wordt doorboord.

    • Schakel je iPhone uit voordat je begint deze uit elkaar te halen.

    • Verwijder de twee 3.4 mm pentalobe schroeven aan de onderkant van de iPhone.

    • Het openen van het scherm van de iPhone zal de waterdichte sluiting van de telefoon aantasten. Zorg dat je vervangende sluitingen klaar hebt liggen voordat je verdergaat of zorg ervoor dat je telefoon niet wordt blootgesteld aan water als je ervoor kiest de sluitingen niet te vervangen.

    Can anyone confirm 7/7P's pentalobe screws have a ring of seal near the screw head?

    Cooper Chase - Antwoord

    Confirmed, the screws have a black ring seal around the head.

    rcheing - Antwoord

    Can’t get the display front

    Bernadette Pfeifer - Antwoord

    From personal experience, I highly recommend before doing this procedure or any other, that you do a backup of your phone (preferably local) in case your procedure goes south.

    ballina5ny - Antwoord

    I purchased the repair tools with the replacement battery from iFixit. The tools include a screw driver and three heads none were labeled 3.4 mm. I think the one that fit the pentalobe screws was labeled Y000. The guide should identify the screw driver head supplied by the kit not 3.4mm.

    Mark Lieberman - Antwoord

    in the iphone 7 replacement battery kit from iFixit, the screwdriver that fits the 3.4 mm pentalobe screws is labeled P2 (and not Y000)

    Jan-Tijn Oppermann -

    3.4 mm is the height of the screw and is not related to the screw driver code.

    Ahmad Vaziri -

    the screwdriver PH000 does not work i wasted two screws and now they dont have the 4 cross mark they are now a circle, i buyed it all from Paraguay and it doesnt work, had to assembly back the parts because i got stuck like i mention with some screws, well im just going to send to a professional to install, thanks

    Martin Frutos, Nuñez - Antwoord

    The bottom screws are Pentalobe, not Phillips.

    Bram Driesen -

    Before starting, I would recommend backing up your Iphone’s data just in case.

    Jon Moylan - Antwoord

    If you managed to make it to this section, just send the phone into apple for 50 + 6 dollars shipping. The ribbon cables on the screen are designed to break. I can literally twist on the rest of the cable and it won’t fall apart but there is a diagonal section where it snaps. This is the fault of apple and the fault of ifixit for misrepresenting the fragility of the cables.

    Ryan Huebert - Antwoord

    Had to reheat it a few times for a minute each with a hairdryer to get the seal to break after pulling and rocking the suction

    Cynthia Lamb - Antwoord

    I’m technically challenged. Is there a premier national service who can professionally install a replacement battery got my 7 +?

    Richard - Antwoord

    Do the screws come out in total?

    YVES THEUGELS - Antwoord

    They may come out or may not. If you loosen as much as you can and they don't come out you should still be able to pry open the bottom. Once you get the screen off you can then push the screws out from the inside.

    Anthony Falabella -

    Is it the P2 you should use for the bottom??

    YVES THEUGELS - Antwoord

    I heated the bottom of the phone with a hairdryer and then used a syringe to put a couple of drops of acetone directly into the bottom two screw holes. I GENTLY pulled on the screen with the suction cup and used the pry tool to GENTLY separate the screen. The sealant is applied around the entire display so be very careful pulling it off so you don’t break the fragile display cables.

    Anthony Scaminaci - Antwoord

    At first it was very difficult to open, per instructions. I used a heat/ice pack and nuked it for 1 minute. The pry tool wasn’t working so I carefully used my pocket knife to wedge the cover open. The rest of the procedure went well until I cracked the glass while trying to get the top right corner to pop off. Other than that mistake, all went well. Tip: before setting the new battery, attach the battery connector first and leave enough room for the taptic engine, or better yet, place the taptic engine before adhering the replacement battery. This way you’ll have a small gap between the two, whereas mine barely fit. Good job on hosting the video, Gwendyl.

    Klaus Preiss - Antwoord

    I love the fact that the screw bit and shaft are magnetic! I almost lost a screw and found it attached to the magnet.

    I used a heat/ice pack and nuked it for 1 minute. At first the display cover was very difficult to open with the pry tool, per instructions. The pry tool wasn’t working so I carefully used the blade of my pocket knife to wedge the cover open. The rest of the procedure went well until I cracked the glass while trying to get the top right corner to pop off. Other than that mistake, all went well. Tip: before setting the new battery, attach the battery connector first and leave enough room for the taptic engine, or better yet, see the taptic engine in place before adhering the replacement battery. This way you’ll have a small gap between the two, whereas mine barely fit because I placed it almost too low.

    Good job on hosting the video, Gwendyl.

    Klaus Preiss - Antwoord

    I replaced the lightning connector assembly and reassembled. The old one did not 'click' into the cable and had corrosion inside, it needed the cable to be placed in a specific way to charge. The new part - does not recognize that a charger is plugged in at all.

    I backtracked the assembly - took it apart, put it back again - and find that every thing on the part works - the mic, speakers, taptic engine.

    The original problem with the cable still persists. Any ideas?

    H K - Antwoord

  2. iPhone 7 Vervanging van de aan-/uitknop, Markeer je plectrums: stap 2, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop, Markeer je plectrums: stap 2, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop, Markeer je plectrums: stap 2, afbeelding 3 van 3
    • Je kunt de onderdelen in je telefoon gemakkelijk beschadigen met het te diep inbrengen van je openingsplectrum. Volg deze stap om je plectrum te markeren en schade aan je toestel te voorkomen.

    • Plaats op 3 mm van de punt van je plectrum een markering met een stift.

    • Je kunt op iedere punt voor een andere markering kiezen.

    • Als alternatief kun je ook een munt als markering gebruiken in plaats van een stift. Plak hierbij de munt op de plectrum zodat de munt tegen je telefoon aandrukt zodra deze een bepaalde diepte bereikt.

  3. iPhone 7 Vervanging van de aan-/uitknop, Instructies voor de anti-klem: stap 3, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop, Instructies voor de anti-klem: stap 3, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop, Instructies voor de anti-klem: stap 3, afbeelding 3 van 3
    • De volgende twee stappen introduceren de Anti-Klem, een handige tool die we aanraden aan iedereen die regelmatig reparaties uitvoert. Als je de Anti-Klem niet gebruikt, sla dan de volgende drie stappen over voor een alternatieve methode.

    • Voor uitgebreider instructies voor het gebruik van de Anti-Klem, lees je deze handleiding door.

    • Trek de blauwe hendel naar achteren zodat de anti-klem vrij kan bewegen. (Op deze manier deactiveer je de openingsstand van de anti-klem.)

    • Schuif de armen over de linker- of rechterzijde van je iPhone.

    • Plaats de zuignappen dichtbij de onderkant van de telefoon—één op de voorkant en één aan de achterkant.

    • Druk beide zuignappen aan, om zuigkracht uit te oefenen op de gewenste plek.

    • Als het oppervlak waarop de zuignappen zich moeten vastzuigen te glad is, kun je wat tape gebruiken voor meer grip.

  4. iPhone 7 Vervanging van de aan-/uitknop: stap 4, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 4, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 4, afbeelding 3 van 3
    • Trek het blauwe handvat naar voren om de armen van de anti-klem te vergrendelen.

    • Draai het handvat 360 graden met de klok mee of tot de zuignappen uit beginnen te rekken.

    • Zorg dat de zuignappen op één lijn met elkaar zitten voordat je begint met het openen van het toestel. Als je ziet dat de zuignappen niet meer op één lijn zitten, maak je ze los en breng je ze weer op de juiste positie aan.

  5. iPhone 7 Vervanging van de aan-/uitknop: stap 5, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 5, afbeelding 2 van 2
    • Verwarm een iOpener en plaats deze tussen de armen van de anti-klem op je telefoon.

    • Je kunt ook een föhn, heteluchtpistool, of een kookplaat gebruiken, maar wees bij het gebruik hiervan extra voorzichtig. Te veel warmte kan tot warmteschade leiden. Vooral het scherm en de batterij zijn hier erg vatbaar voor.

    • Vouw de iOpener zodat deze op de onderkant van de iPhone komt te liggen.

    • Geef de lijm een minuutje de tijd om los te komen zodat de anti-klem een opening kan creëren.

    • Steek een plectrum in de opening onder het scherm.

    • Als de anti-klem er niet in slaagt een opening te creëren die groot genoeg is voor je plectrum gebruik je meer warmte en draai je het blauwe handvat een kwartslag met de klok mee.

    • Draai het handvat nooit verder dan een kwartslag per keer en wacht een minuut voordat je de anti-klem weer besluit aan te draaien. Laat de anti-klem het werk voor je doen.

    • Sla de volgende drie stappen over.

  6. iPhone 7 Vervanging van de aan-/uitknop, Verwarm het scherm: stap 6, afbeelding 1 van 1
    • De volgende drie stappen laten je zien hoe je het scherm opent met behulp van een enkele zuignap.

    • Het verwarmen van de onderkant van de iPhone helpt de lijm, die het scherm op z'n plek houdt, te verzachten, wat het makkelijker maakt om de telefoon te openen.

    • Gebruik een föhn of een warmtepistool, of prepareer een iOpener en leg deze op de onderkant van de iPhone gedurende ongeveer 90 seconden om zo de lijm die eronder zit te verzachten.

  7. iPhone 7 Vervanging van de aan-/uitknop, Haal het scherm los: stap 7, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop, Haal het scherm los: stap 7, afbeelding 2 van 2
    • Druk een zuignap op de onderste helft van het voorste paneel, net boven de thuisknop.

    • Zorg dat de zuignap niet overlapt met de thuisknop, aangezien dit ervoor zal zorgen dat de zuignap zich niet vast kan zuigen aan het scherm.

  8. iPhone 7 Vervanging van de aan-/uitknop: stap 8, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 8, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 8, afbeelding 3 van 3
    • Trek de zuignap omhoog met een stevige, constante kracht om zo een kleine opening tussen het voorste paneel en het frame van de telefoon te creëren.

    • Steek een openingsplectrum in de opening.

    • De waterdichte lijm die het scherm op z'n plek houdt is erg sterk; het creëren van de opening kan dus heel wat kracht vereisen. Als je moeite hebt met het openen van de telefoon, dien dan meer warmte toe en wiebel het scherm op en neer om de lijm te verzachten totdat de opening groot genoeg is voor je tool.

  9. iPhone 7 Vervanging van de aan-/uitknop: stap 9, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 9, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 9, afbeelding 3 van 3
    • Schuif je openingsplectrum langs de linkerkant van de telefoon omhoog, beginnend bij de onderkant en in de richting van de volumeknoppen en de stilteknop, en snijd onderweg alle lijm door die het scherm op z'n plek houdt.

    • Stop in de buurt van de linker bovenhoek van het scherm.

    • Probeer de bovenkant van het scherm niet los te wrikken van de achterste behuizing, aangezien deze wordt vastgehouden door middel van plastic klemmen die kunnen breken.

  10. iPhone 7 Vervanging van de aan-/uitknop, Informatie over het scherm: stap 10, afbeelding 1 van 1
    • Er loopt een aantal makkelijk te beschadigen kabels langs de rechterkant van de iPhone. Steek je plectrum daar niet in de opening om te voorkomen dat je je toestel beschadigt.

  11. iPhone 7 Vervanging van de aan-/uitknop: stap 11, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 11, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 11, afbeelding 3 van 3
    • Steek je openingsplectrum opnieuw in de rechter onderhoek van de iPhone en schuif deze nu langs de rechterzijkant omhoog. Snijd ook hier alle lijm door die je onderweg tegenkomt.

    • Steek je plectrum ook hier niet dieper dan 3 mm in de opening om te voorkomen dat je de schermkabels beschadigt.

  12. iPhone 7 Vervanging van de aan-/uitknop: stap 12, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 12, afbeelding 2 van 2
    • Trek met beleid aan de zuignap om zo de onderkant van het scherm op te tillen.

    • Til het scherm niet meer dan 15º omhoog of je riskeert het afklemmen of afscheuren van de lintkabels die het scherm verbinden.

    • Trek aan het kleine lipje op de zuignap om deze van het voorste paneel te kunnen verwijderen.

  13. iPhone 7 Vervanging van de aan-/uitknop: stap 13, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 13, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 13, afbeelding 3 van 3
    • Steek een openingsplectrum onder het scherm en schuif deze langs de linker onderhoek en linkerzijde omhoog om de laatste lijm door te snijden.

  14. iPhone 7 Vervanging van de aan-/uitknop: stap 14, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 14, afbeelding 2 van 2
    • Schuif de schermmodule een beetje omlaag (weg van de bovenkant van de telefoon) om deze los te krijgen uit de klemmen die het scherm aan de achterste behuizing bevestigen.

  15. iPhone 7 Vervanging van de aan-/uitknop: stap 15, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 15, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 15, afbeelding 3 van 3
    • Open de iPhone door het scherm van de linkerkant naar rechts te kantelen, alsof je de achterste kaft van een boek opent.

    • Probeer het scherm nog niet volledig los te koppelen, aangezien deze nog steeds aan het logic board van de iPhone verbonden is met een aantal kwetsbare lintkabels.

    • Om het scherm open te houden en aan de telefoon te kunnen werken, kun je het scherm tegen een object laten leunen.

  16. iPhone 7 Vervanging van de aan-/uitknop, Loskoppelen van de batterij: stap 16, afbeelding 1 van 1
    Gereedschap gebruikt in deze stap:
    Tri-point Y000 Screwdriver
    $5.99
    Koop

    Ahhh shoot! accidentally ordered tri-wing vs tri-point (must have just looked for y000).. It seems they only did this to annoy repair folks because not everything is tri-point on the phone...

    Steve - Antwoord

    These screws just spin for me. They don't back out, but the heads aren't stripped either. I've tried applying backpressure to help lift the screws, but no luck

    Jeff Hurst - Antwoord

    The Y000 took out one of the screws but not the other 3. I even tried the PH000 as suggested but nothing.

    dbright - Antwoord

    What driver do I need to remove these screws i’m stuck

    Nasser Nader - Antwoord

    i cant use, the Y000 it isnt working.

    joscarlos91 - Antwoord

    What if I stripped a screw what do I do??

    Jacob Ramos - Antwoord

    Yep, only the 2.4mm came out, other 3 won’t budge, and worried I’ve stripped the heads. Anyone got any ideas?

    Stephen Babbage - Antwoord

    It’s the screwdriver bit that is the problem. I had the same issue with 2 Y000 bits not grabbing the screw properly. I fixed it by using a small 3 sided file to slightly grind the groves in the Y000 bit just a bit deeper. Then the bit worked like a charm on these screws.

    Jim Staples - Antwoord

    Use Y000 on all 4. U have to be very sensitive on the 1.2mm screws. Put the bit in the screw, put the left pointing finger on top of the screwdriver and turn the driver carefully to the right until you feel a “bump”, thats the trick :-), then you are able to screw the screw out.

    Magne Eivindson - Antwoord

    For me the key here was a LOT of downward pressure to ensure the Y000 bit caught in the screw. Not sure i can describe how much exactly, but is was significant. Otherwise the bit would not catch.

    Erik Fredriksen - Antwoord

    What do I do if I Stripped one of them?

    Adam Corral - Antwoord

    Can’t get them removed what to do ?

    cowling_luke - Antwoord

    Managed to get the central one out. The upper one won't move, the lower one I've popped out with some force. This allows you to rotate the cover enough to unplug the various bits. Not ideal, but works. I've tried applying a lot of pressure, using the tighten/ loosen method, but the heads have just got mashed… no wonder Samsung are now No1, sigh…

    jimpoolio - Antwoord

    You need to be careful when just rotating the cover as you can accidentally slice through the two black antennas! You only need to nip them…As you can tell I have done this in the past :/

    Kyle Webb -

    The first, longer screw came out fine, but the other three wouldn’t budge, regardless of more/less pressure or a slight angle or anything. I finally filed down the tip of the Y000 bit ever so slightly, and then it worked. Hope this helps someone.

    Harmony - Antwoord

    Filing down the bit worked for me. The tip about putting an index finger on the end of the screwdriver handles and then turning gently until it clicks into place was very helpful! Using these 2 tips I didn't need much downward pressure. Screws are out in a few turns.

    Chris Bennett - Antwoord

    If you can’t get the bit to grip the screw properly, you can use a little bit of the water-proof sealing between the bit and the screw. That worked for me. Hope this helps anyone.

    jvalaamo - Antwoord

    Mine came out easily. I placed the screws in the area where the bit goes in my kit so I can keep track.

    Gina Torres - Antwoord

    I used a bunch of medicine cups to track my screws. You need like 12 if you want them all in cups. I ran out. There are so many different sizes that literally vary by 1mm. The tolerances on these things are tight.

    Ray Bieze - Antwoord

    I use a 28 day pill box and keep every screw separate and reburn to exact slot because they all vary in length, width and can really damage u phone if too long and nt secure if to small.  use a magnetised screwdriver,  or make the cheap freebees magnetic for a short period by rubbing it up an a magnet. lol

    scallyteacher - Antwoord

    Absolutely ridiculous had to go get a different one just stupid

    mark golling - Antwoord

    I couldn’t get the lowest one out and just turned the metal bracket out of the way and replaced battery.

    qwerty77x - Antwoord

    Was able to get the outer bracket screws out using fine needle nose pliers 90 degrees straight down for the outer ones by pressing down a little and using medium gripping force. Had to take these out first before i could use tweezers on the middle one, for which I had to use tweezers to hold the screw, then rotating the bracket (not the screw) counter clockwise a few mm many times over to slowly unscrew it 1/32th of a turn at a time, repeat. (this loosened middle screw). Think ‘rotating bracket 3minutes/degrees counterclockwise at a time while holding screw in place.) You are gonna need really small/fine pliers and tweezers for this because the heads are countersunk into the bracket.

    Galen Wollenberg - Antwoord

    The top screw in the step was much longer than 1.2mm. It has the same head as the 1.2mm, but different than the 2.4mm. It’s good to keep track of where they came from.

    All are so small that I thought I’d lost one, when it was still sitting in the phone.

    Mark - Antwoord

    To help tell if the screw is turning, put a small dot from a marker on the head of the screws.  This helped me to know I wasn't just stripping the head.

    Darren Thibodaux - Antwoord

    try heating the iPhone with a hairdryer or a bag of rice or about 60 degrees in an oven for 3 minutes . It has worked for me. If the screws don’t come out while hot the will come out as the iPhone cools.

    David Howard - Antwoord

    A small tapered triangle file using moderate pressure did the trick for me.

    Jack - Antwoord

  17. iPhone 7 Vervanging van de aan-/uitknop: stap 17, afbeelding 1 van 1
    • Verwijder het plaatje op de onderste batterijaansluiting.

    my battery cable connector was stuck to the bottom of this metal bracket plate so be careful when you lift it off

    Josh Martin - Antwoord

    This may have been intentionally done by Apple to make sure the battery gets disconnected before any other connector is disconnected. So always make sure to disconnect the battery before disconnecting and reconnecting the connectors for the display.

    Oscar Moreno - Antwoord

    So…I forgot to put this bracket back on when reassembling. Now I’ve adhered the display to the case and don’t have another adhesive strip…so I’m wondering: what purpose does this bracket serve? The phone is powering on and seems to work okay.

    Am I going to run into trouble with this bracket missing?

    Ian Fritz - Antwoord

    Well, that didn’t last long. The phone shuts down without warning. So I guess that plate is important…

    Ian Fritz -

    I also forgot to put the battery shield in, and adhered the display. I’m tempted to leave it like that. However, your negative experience is a good data point telling me to not be cheap.

    Ordered a new adhesive , under $2 shipped from eBay.

    Yishai Sered -

    Thanks, Josh Martin! Mine was stuck too, so I lifted carefully.

    Cynthia Lamb - Antwoord

  18. iPhone 7 Vervanging van de aan-/uitknop: stap 18, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 18, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 18, afbeelding 3 van 3
    • Gebruik de punt van een spudger om de batterijaansluiting uit het contact op het logic board omhoog te duwen.

    • Buig de kabel lichtjes omhoog om te voorkomen dat deze tijdens de reparatie per ongeluk contact maakt met het contact en de telefoon inschakelt.

    Was kann passieren wenn man diesses Kabel vergessen hat zu entfernen `?

    Julian Eltrich - Antwoord

    Reconnecting the battery poorly can cause the iPhone to appear to be properly powered and functional, but then suffer a reboot loop.

    I had difficulty after a screen replacement, and the Console app on my Mac showed that the ‘thermalmonitord’ process was throwing lots of errors from not getting any sensor readings from the battery. It would never charge past 1% and just kept rebooting.

    The contacts on this conector looked fine so even though I had reseated this connector several times already, I reconnected it very firmly using my thumb and a spudger to really press all the corners and middle and really gave it a good massage and then finally it showed the normal dead battery screen and started properly charging and eventually booted back up to normal functionality.

    It seems the battery has to be able to transmit data to the phone to say it’s not overheating or iOS will not allow any current into the battery to recharge it, and the kernel will panic from the null readings and just reboot over and over again.

    jason - Antwoord

    In my case, the battery connector was attached to the bracket. We just left it connected bracket when we pryed it up.

    Dave Miller - Antwoord

    Reconnecting the battery connector was a bit difficult in my case. The cable that comes out of the battery was a tiny bit too long, or that I placed the battery a bit too high (i.e., too close to the top of the phone). It took me several frustrating minutes of fiddling with the connector for it to sit right into the socket. I was not sure if that was connected correctly but, alas, the phone came back to life when it was turned back on.

    Tomoharu Eguchi - Antwoord

    VERY IMPORTANT NOTE: Please READ the reply here by jason.

    It is very easy to knock off or nudge the little pins near the battery socket, see https://guide-images.cdn.ifixit.com/igi/... and https://guide-images.cdn.ifixit.com/igi/....

    Those pins are the data lines to extract battery info: temperature, charge, etc. If you accidentally nudge/knock off them the phone could appear to work normally, even for a few days. But then you will start getting wrong battery reads and then after that it may suffer a reboot loop. If you enter settings > privacy > analytics & improvements and you scroll down you will find panic errors from thermalmonitord that there are missing sensors (TG0B or TGXXX) and you will have to micro solder them. DO NOT NUDGE THEM and double check the socket connector when reconnecting the battery.

    PJM - Antwoord

    After successful screen replacement, returning to give my thanks here. Excellent tips from you all! Careful removing the lower bracket - mine was stuck to this battery connector, which came up with the bracket. Luckily no cable or connector damage. Be careful. Thank you all!

    dantegd - Antwoord

    after installing new ifixit battery kit, note the foam on the new battery is thicker than old apple one, managed to remove the old foam and swap to new battery connector, sheild plate now level

    Neil Mills - Antwoord

  19. iPhone 7 Vervanging van de aan-/uitknop, Schermmodule: stap 19, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop, Schermmodule: stap 19, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop, Schermmodule: stap 19, afbeelding 3 van 3
    • Zorg dat de batterij is losgekoppeled voordat je de kabels in deze stap los- of vastkoppelt.

    • Gebruik een spudger of je nagel om de twee onderste schermaansluitingen los te koppelen door deze in een rechte beweging uit het contact op het logic board omhoog te duwen.

    • Om drukaansluitingen zoals deze weer aan te sluiten, positioneer je deze totdat op z'n plek lijkt te zitten en duw je één kant van de aansluiting omlaag tot deze vastklikt, om vervolgens hetzelfde te doen aan de andere kant. Druk niet op het midden, want als de aansluiting verkeerd zit, zul je de pinnen buigen en zo schade veroorzaken.

    • Als je witte lijnen op het scherm of een volledig wit scherm ziet, of de touchscreen-functie werkt gedeeltelijk of helemaal niet na het in elkaar zetten van je telefoon, kun je proberen deze kabels weer los te koppelen en opnieuw aan te sluiten. Zorg ervoor dat ze goed en stevig aangesloten zijn.

    To be honest you don’t really need to disconnect the display cables in step 15 or 16 to get the battery out. Just keep the suction cup on the screen to keep it propped up and to give the cables some slack. The only reason to take these cables off is that it’s a pain to apply the replacement display adhesive with those cables in the way. If you’re not re-waterproofing your phone just leave these attached.

    Vervanging van de kleefstrips van een iPhone-scherm

    minimalist - Antwoord

    MAKE SURE you hold the top screen when dislodging the cable connections. I let the screen lie flat down and ended up tearing one of the cable connections, now my touch ID does not work at all! I’m going to have to order a whole new screen.

    Arjun Nagarajan - Antwoord

    Don’t miss that SECOND CONNECTOR like I did. It will break very easily if not disconnected :(

    garrett peek - Antwoord

    An earlier comment said to re-apply the suction cup to the right side of the display so that it acts as a stand when the phone is partially opened. That’s a great idea, and helps a lot for this step and the next.

    Mark - Antwoord

    Hey – I broke one of these flex cables and I cant find them to purchase anywhere. Can somebody help me? It’s the LCD connector first and what is the second flex cable for? Thanks!

    Chan Ty - Antwoord

    I broke the second (smaller) display connector flex cable.

    1) Is it replaceable or repairable?

    2) Where can I get the replacement?

    Ben Blom - Antwoord

    Same happened to me. What solution did you find? Could you replace a part to make it work? Thank you!

    Viktoria -

    I replaced the screen and have ended up with a blank screen. Touch control seem to work (touch button works and I can shut down the phone by pressing power button for some seconds and then swipe left to right in the upper part of the screen). But the screen is blank. I’ve tried to disconnect and connect the two connectors in step 16 but with the same result (blank screen). What do I need to do?

    Thanks for advice!

    Bjorn - Antwoord

    this point is the most important in the whole manual.

    Please pay attention not to strain the flex cables or they will end up breaking

    Jose Joaquín Sanz Iniesta - Antwoord

    I should have been more careful - the second cable tore off.

    My own fault after having done this replacement about four times previously without any issues, I clearly got cocky and didn’t pay enough attention.

    Be VERY CAREFUL and remember to unplug those cables. Don’t skip steps.

    I’ve now had to order a replacement screen.

    Stuart - Antwoord

    Echo minimalist’s comment here. Prop the display up and skip to step 19 to save time and remove risk.

    .A. - Antwoord

    If you replace the screen and there is no display apply io propyl alcohol 99.9 & purse to both connectors on the screen and on the iPhone with a clean toothbrush and let them dry for 45 minutes and then fit the screen and reassemble the iPhone..

    It works for me . when I get a new screen I do t5his before fitting it.

    David Howard - Antwoord

    I tried to save time by not removing the screen during battery replacement as some comment here, HOWEVER, I ended up having to use a little force to remove the battery and in the process broke the second, lower smaller cable, resulting in loss of home button function and needing to get a new screen. Next time I will follow these steps and completely remove the screen during a battery replacement

    chrislacey - Antwoord

    I removed the screen and cable still got ripped during reassembling :(

    Viktoria -

    There is a critical fact missing from the steps here, for reassembly: That bottom (underlying) cable is longer than it should be. Loads of people are reporting that the Home button is dead after this repair, but the cables aren't torn. I'm pretty sure this is why. Here is a picture of the problem.

    When reassembling the phone, you must poke this cable back into the body of the phone while you bring the halves together, or you will crush, crimp, and destroy the cable.

    Gavin Stokes - Antwoord

    I’m only reading your very useful comment now, after the exact thing happened to me and my cable got ripped during reassembling phone. Would you be able helping me naming this part, so I can look for a new one? Thank you very much!

    Viktoria -

    thanks gavin. ifixit should have included this piece of info.

    soupamanx -

    Can somebody help me with the name of the part that these cables belong to? The bottom one got ripped during my battery replacement, I need a new one but unsure what to look for.

    Viktoria - Antwoord

  20. iPhone 7 Vervanging van de aan-/uitknop: stap 20, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 20, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 20, afbeelding 3 van 3
    • Verwijder de twee 1.3 mm Phillips #000 schroeven die het plaatje bovenop de aansluiting van de sensormodule in het voorste paneel bevestigen.

    • Het kan voorkomen dat sommige van deze modellen Y000-schroeven bevatten. Apple heeft op een gegeven moment gekozen deze specifieke schroeven in plaats van de Phillips-schroeven te gaan gebruiken.

    Has anyone had trouble getting these two screws off? I’ve been working on these for about 10 minutes and the LEFT screw wont spin. It seems like the little PH000 screwdriver bit won’t even grip it. (The one of the right comes off, no problem)

    It looks like I’ll have to pick this project up again with a screwdriver that will actually take off this piece.

    Makana Sylva - Antwoord

    If you’re having trouble removing these screws;

    the screw on the right goes into a standoff screw that is screwed into the frame.The left one goes into the logicboard.

    If your phone is used most likely it has been repaired in the past and the person that repaired it put the screws in way too tight.

    If your phone is brand new And you know 100% it is then the problem is your screwdriver.Stop before you strip it completely and buy a better screwdriver (EBAY).

    If you already stripped the screw head take the phone to a shop before you break it.

    there are ways to get them out but truthfully it’s extremely dangerous and sometimes your better off quitting while you are ahead.

    Vegeta Barrett -

    The right screw kept spinning, tried different levels of force but didn’t work. I left the screw on and bent the shield to get to the cable.

    s h - Antwoord

    I used a #1 flat head tip to loosen.

    Peter Pearson - Antwoord

    I couldn’t get the two screws out either—used the correct screw tip and everything. Stripped the screw. Will now attempt to just keep the cable attached…..

    Therese Peffer - Antwoord

    Use the PH000 and apply a little more force before spinning, should come right out!

    Sierra Scolaro - Antwoord

    ^To anyone having trouble, this is the correct answer. Put the phone on a firm surface, align your driver carefully, press down hard, and twist. As long as your driver is approximately the right size, it’ll come out.

    Jeff Suovanen -

    the two screw i have are stripped and i have n way of getting either screws off whats my next bet

    Alexis Marie Colon - Antwoord

    The PH000 bit is to large. I can’t get the screws out either which really sucks…now I have to put everything back together, find another bit that will work and try this again another day. Not impressed with IFIXIT’s attention to detail so far :-(

    Ryan Welborn - Antwoord

    Using iFixit’s driver kit, I prefer a PH00 for this, which is larger than the PH000. If you think the PH000 is too big, something is wrong.

    Jeff Suovanen -

    I think part of the issue with the iFixit PH000 is that it is slightly too pointy. The PH00 fits better because the splines engage the slots of the screw before the point bottoms out. The PH000 tip bottoms out in the screw’s center point and the splines don’t engage as well. I have other PH000 tips that are more blunt nose and they work better than the iFixit bit.

    rcarswell - Antwoord

    Use the J00 bit. Worked perfectly

    efazio588 - Antwoord

    PH000 screwdriver didn’t work for any of these screws, or the barometric vent, or the taptic engine. It was too big. I had to use a different screwdriver from another kit I had.

    minimalist - Antwoord

    I’d do this step before removing the ribbon cables by the battery connector. That way you can disconnect all of them at the same time.

    Ray Bieze - Antwoord

    i used the little +-shape 30 mm screwdriver (not the Y…but the + shape).

    mason - Antwoord

    the cable tore. is that it i need a new phone?

    patricia loving - Antwoord

    You don’t need a new phone, but your selfie camera and phone speaker will not work. You can get replacements for that about $10.

    jack jones - Antwoord

    Reconnecting this cable and coverplate took a good 20 minutes. O_O

    Nicole Crome - Antwoord

    What can I do to remove the screw (I stripped it)

    Alex Vu - Antwoord

    I also had issues to loosen up the screws, in two parts the right side up and the left side down, i think the PH000 is to pointy or something or its too hard for the srews of the iphone, i cannot take it off and know im regreting i bought i order all the way from Paraguay in south america and know so angry it doesnt work

    Martin Frutos, Nuñez - Antwoord

    I skipped this step. Just be really careful not to pull on the screen.

    Takumi Arai - Antwoord

    The guide says they changed these to the Y000 “at some point in the t middle of the product’s lifecycle”…

    That can’t be true, I have a *day one*, preordered iPhone 7, and mine had, unmistakably, Y000 screws!

    and also, I’m just faithfully following the guide here, but can anyone clarify *why* is is necessary to entirely remove the display AND the Taptic Engine at all? The battery seems accessible just fine… oh well

    PS- I’m doing this on an older backup iPhone 7. My iPhone 12 Pro just went berserk and stopped working completely a little over a year after I got it day one of its release… since the iPhone X I’ve only had easily breakable, overly sensitive phones. I’ve had every numbered iPhone except for the 8 (I got the X released at the same date) and the 11, and man, are these newer iPhones post X fragile!

    Cam F - Antwoord

    This worked for me! As mentioned use PH000 and apply pressure and then unscrew the screws. They are tiny, adhere to a piece of tape so you don't lose them.

    Rosie J - Antwoord

  21. iPhone 7 Vervanging van de aan-/uitknop: stap 21, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 21, afbeelding 2 van 2
    • Koppel de aansluiting van de sensormodule in het voorste paneel los van het contact op het logic board.

    • Zorg dat je, bij het opnieuw aansluiten van deze drukaansluiting, één kant per keer vastklikt om het risico te vermijden dat je de aansluiting verbuigt.

    Das ist sehr mutig, das Kabel dort so zu strapazieren.

    Mich würde das Display daneben stellen und mit irgendetwas stützen, dass es nicht umkippen kann um Beschädigungen an dem Kabel zu vermeiden. Das reißt sehr schnell ein.

    Detlef Menninger - Antwoord

    Is this the connector for the earpiece, as well? I did the screen replacement and everything worked, except now I can’t use my earpiece… I’m afraid I didn’t fully connect this particular portion.

    Victor Bui - Antwoord

    @victorbui714 Correct, this is also the connector for the earpiece speaker. Check the flex cable carefully and make sure it wasn’t pinched or torn. Make sure the connector socket is clean (give it a blast with some compressed air if needed) and try reseating it. If that doesn’t help, you may want to remove the earpiece speaker and inspect the four springs on the back, and check that they’re intact and making good contact with the four circular pads on the flex cable. Give the pads a wipe with some IPA and try not to leave any skin oils on them. If none of that works, try replacing the entire flex cable/sensor assembly. Good luck!

    Jeff Suovanen -

    This is the only connector that is quite easily possible to put back in the wrong way. If you do so, the phone will just get into a continuous loop where it shows the boot screen, goes blank and then shows the boot screen again and again. If this happens, do not despair-just put it back in the right way.

    Roy Mathew - Antwoord

    After putting together, I had a continuous loop boot up (as noted above). I saw articles where this (front panel sensor connection) was the reason. I disconnected this connection and the boot up loop stopped. I tried reconnecting several times but had the same problem (boot up loop). However, it turns out that I needed to apply extra pressure when installing until a heard a (faint) second click when pressing down. Note - before I was using the spudger to press the connection together, which didn’t do the job. I ended up using my finger to press harder to get it to click in. Solved that issue.

    Ed Scannell - Antwoord

    The ribbon cable on this step is torn. Is this something that can be replaced? Is this only to the earpiece?

    John Daily - Antwoord

    The ribbon cable on this step is torn. Is this something that can be replaced? Is this only to the earpiece?

    Sarah Valencia - Antwoord

  22. iPhone 7 Vervanging van de aan-/uitknop: stap 22, afbeelding 1 van 1

    When removing the screen, be aware of the two tiny square black rubber grommets on the Penelope screw brackets that secure the screen. They can fall off very easily and be lost without even knowing it (it happened to me, but was lucky enough to find them).

    Guy Cooley - Antwoord

    Sorry, I’m so unclear about when to replace the Adhesive tape. Should I put the iPhone 7 Display Assembly Adhesive at this step, or after I’ve replaced the battery?

    Victor Bui - Antwoord

    @victorbui714 Battery first, then adhesive during reassembly, as it says in the instructions. ;)

    Jeff Suovanen -

    This is the 3rd screen iv put in my phone and everyone them bust at the top by the camera every time iv bought one of these screen idk if it’s the manufactures fault or what?

    trent bost - Antwoord

    @trentb28922 Ouch! That’s not normal. Is your phone’s frame bent? Are you having to use a lot of force when you install the display?

    Jeff Suovanen -

    If the instructions are followed step by step, then adding the adhesive comes before changing the battery.

    If I had to do it all over again, I'd skip adding the adhesive, because you have to disconnect the battery, plus the two lower display connecters and the front panel sensor assembly connector. It was a nightmare trying to marry the components back together without disturbing the wire prongs, and I don't even want to talk about reinserting the tiny screws that kept twirling around on the tip of the screwdriver as well. It wasn't worth the time or aggravation!!

    If you decide to skip this step, just avoid using your iPhone near water.

    Rosie J - Antwoord

  23. iPhone 7 Vervanging van de aan-/uitknop, SIM-kaart: stap 23, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop, SIM-kaart: stap 23, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop, SIM-kaart: stap 23, afbeelding 3 van 3
    • Steek een uitwerpingstool voor de SIM-kaart of een paperclip in het kleine gaatje in de SIM-kaarthouder.

    • Duw deze naar binnen om de kaarthouder naar buiten te duwen.

    • Dit kan wat kracht vereisen. Zorg daarom ook dat de uitwerptool recht in het gat geplaatst is om zeker te weten dat je het uitwerpmechanisme in de telefoon niet zult beschadigen.

    • Verwijder de SIM-kaarthoudermodule uit de iPhone.

    • Zorg dat de SIM-kaart, wanneer je deze terugplaatst, correct is geplaatst ten opzichte van de SIM-kaarthouder.

    Received a sim card tray from IFIXIT for my iphone 7. I can’t seem to get it to close flush no matter how hard I try. Any suggestions?

    AJ Dereume - Antwoord

    Why would it require a significant amount of force? Is it because the iPhone 7 is water resistant? When I removed my tray it was like it was stuck in goop inside the phone and the tray had a glue like sticky substance on it? It did not ‘click’ back in smoothly like my other iPhones, I had to push it against the ‘goop’. Is this normal for iPhone 7??

    Rebecca Diakun - Antwoord

    I used the tip of the super pointy tweezers, and it worked well.

    Cynthia Lamb - Antwoord

  24. iPhone 7 Vervanging van de aan-/uitknop, Logic board aansluitingen: stap 24, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop, Logic board aansluitingen: stap 24, afbeelding 2 van 2
    • Gebruik het platte einde van een spudger om de naar achteren gerichte camera-aansluiting los te koppelen.

  25. iPhone 7 Vervanging van de aan-/uitknop: stap 25, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 25, afbeelding 2 van 2
    • Verwijder de volgende Phillips schroeven die het plaatje over de naar achteren gerichte camera aan de achterste behuizing bevestigen:

    • Eén 1.3 mm lange schroef

    • Eén 2.5 mm lange schroef

    I couldn’t get my 1.3mm screw out. It’s not required thankfully as you can just bend the cover up and out of the way to complete the rest of the steps.

    Ray Bieze - Antwoord

    i removed them with PH000

    Flavien - Antwoord

  26. iPhone 7 Vervanging van de aan-/uitknop: stap 26, afbeelding 1 van 1
    • Verwijder het plaatje.

  27. iPhone 7 Vervanging van de aan-/uitknop: stap 27, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 27, afbeelding 2 van 2
    • Gebruik de punt van een spudger om de antennebusaansluiting, welke zich links naast de achterste cameramodule bevindt, omhoog te duwen en los te koppelen.

    There is one Step missing before removing the flash light cable: Remove Camera cable, right?

    Achim Breidenbach - Antwoord

    I broke this and can’t find it on amazon. Is it part of the volume control flash connector? If not, can you send me a link on where to find this connector,…and possible instructions on how to replace?

    Daniel Buhler - Antwoord

  28. iPhone 7 Vervanging van de aan-/uitknop: stap 28, afbeelding 1 van 1
    • Verwijder de twee 1.2 mm lange tri-point schroeven die het plaatje over de bovenste kabel bevestigen.

    these are too tight cant get rid off them from y000

    Narendra Mane - Antwoord

    ok with Y000 from pro tool kit

    Flavien - Antwoord

    Had to push down to get the Y000 in place

    Cynthia Lamb - Antwoord

  29. iPhone 7 Vervanging van de aan-/uitknop: stap 29, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 29, afbeelding 2 van 2
    • Verwijder het plaatje over de bovenste kabel.

  30. iPhone 7 Vervanging van de aan-/uitknop: stap 30, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 30, afbeelding 2 van 2
    • Gebruik het platte einde van een spudger om de bovenste kabelaansluiting los te koppelen.

    Este cable q funciona tiene porfavor lo desconecte y funciona normal

    Johnny Bolaños - Antwoord

  31. iPhone 7 Vervanging van de aan-/uitknop: stap 31, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 31, afbeelding 2 van 2
    • Verwijder de vier Phillips-schroeven die de Wi-Fi-antenne bevestigen:

    • Drie 1.2 mm lange schroeven

    • Eén 1.7 mm lange schroef

    I lost one of these 1.2 mm screws. Will that affect the signal reception?

    Bethany Knaebel - Antwoord

    There is another screw connecting the antenna to the case.

    tbaiello - Antwoord

    How do you open the 1.7mm screw? LOL

    Kyle Victor - Antwoord

    The screws are not threading in for some reason. I measured the screws to be exactly 1.2mm with a caliper.

    Loopy75 - Antwoord

    Yes there are 4 x screw 3 x 1.2mm and 1x 1.7mm securing the antenna to the case

    ANDREW - Antwoord

    Yes : 4 screws and not 3 !!

    sirthomasnardin -

  32. iPhone 7 Vervanging van de aan-/uitknop: stap 32, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 32, afbeelding 2 van 2
    • Verwijder de antenne die linksboven geplaatst is.

    ** also remove the small Phillips screw fastening the WiFi antenna to the top rear casing of the phone

    iBroke - Antwoord

  33. iPhone 7 Vervanging van de aan-/uitknop: stap 33, afbeelding 1 van 1
    • Verwijder de volgende Phillips schroeven:

    • Eén 1.3 mm lange schroef

    • Eén 2.2 mm lange schroef

    Möglicherweise muss man den Kleber zuerst entfernen!

    Evan Winter - Antwoord

  34. iPhone 7 Vervanging van de aan-/uitknop: stap 34, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 34, afbeelding 2 van 2
    • Verwijder het plaatje.

    What's this bracket called

    Cris Velasquez - Antwoord

    %#*@, lost that part during the job, thought it’d be alright without it. Couple days later figured out NFC doesn’t work anymore. Any ideas on where to get this part from, colleagues?

    azowux - Antwoord

  35. iPhone 7 Vervanging van de aan-/uitknop: stap 35, afbeelding 1 van 1
    Gereedschap gebruikt in deze stap:
    Standoff Screwdriver for iPhones
    $5.49
    Koop
    • Verwijder de 2.2 mm lange standoff schroef van de aardingsbeugel.

    • Standoff schroeven kun je het beste verwijderen met behulp van een standoff-schroevendraaier of -bitje.

    • Het moet ook lukken met een kleine platkopschroevendraaier—maar wees in dat geval wel extra voorzichtig en zorg ervoor dat de schroevendraaier niet wegschiet en omringende onderdelen beschadigt.

    What bit is this? The link doesn’t use the same name.

    Mike Moran - Antwoord

    I didn’t even have an eyeglass repair kit flathead, so I hit the end of a paperclip with a hammer to make a flathead, and it works!

    Ark - Antwoord

    I hate getting the deep into a repair to find there’s a tool missing. This bit should be part of the toolkit!

    Ark - Antwoord

    Its in the toolkit now. Looks like a Philips head but up close the end is squared off with a point in the middle.

    Jesse de Vries -

    I received two boxes - one box contained the repair part, the other was the tool kit. I only opened the tool kit before disassembling the phone. The standoff screwdriver bit was not in there. Neither was the guitar pick. I used a real guitar pick and a small standard screwdriver from my toolbox. When I was ready to reassemble, I opened the repair part box and guess what was in there - the standoff screwdriver bit and guitar pick. So, I guess if you just order the part it will come with (at least) those two tools. The tool kit contains tweezers, suction cup, three screwdriver bits (tri-point, pentalobe, and phillips) and screwdriver handle, a long black spudger with a flat end and a pointy end, and a smaller, thicker spudger with a wide, flat ends.

    bronyaur - Antwoord

    The flat end of the spudger works a treat too.

    Robert Trammel - Antwoord

    Thank you, bronyar. Since there is a box labeled “Repair Tools”, I never would have looked in the parts box for tools. I was able to use the standoff tool to takie the phone apart, not just to put it back together.

    Mike Ruzicka - Antwoord

    I used standoff bit for iPhone from my pro tool kit

    Flavien - Antwoord

  36. iPhone 7 Vervanging van de aan-/uitknop: stap 36, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 36, afbeelding 2 van 2
    • Gebruik een pincet om de aardingsbeugel van het logic board op voorzichtige wijze uit de weg te buigen.

    I accidentally broke the grounding bracket, is it very important to get a new one to replace? as I can't seem to find them for sale anywhere

    Mustifa shah - Antwoord

    I also broke it. Did your phone work after?

    Did you find a replacement?

    Ben Schorr - Antwoord

    Did your phone work ?

    Emin -

    also broken does it work without?

    Emin - Antwoord

    I broke mine while doing this step. A bit confusing. You’re just supposed to bend it out the way, not pull on it entirely. Will the phone still work without this?

    Chandler Forrest - Antwoord

    $@$*, i broke the grounding bracket

    Z1xus - Antwoord

    I just didnt bend this one.. Ill tell you how it went

    Lauren Campbell - Antwoord

  37. iPhone 7 Vervanging van de aan-/uitknop, Logic board: stap 37, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop, Logic board: stap 37, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop, Logic board: stap 37, afbeelding 3 van 3
    • Gebruik de punt van een spudger om de twee antennekabelaansluitingen uit hun contacten op het logic board te tillen.

  38. iPhone 7 Vervanging van de aan-/uitknop: stap 38, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 38, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 38, afbeelding 3 van 3
    • Gebruik een pincet om de antennekabels voorzichtig los te koppelen van het metalen contact op het logic board en deze aan de kant te duwen.

  39. iPhone 7 Vervanging van de aan-/uitknop: stap 39, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 39, afbeelding 2 van 2
    • Gebruik de punt van een spudger om de onderste kabelaansluiting los te koppelen.

    Wat voor kabel is dit? Deze is beschadigd bij mijn IPhone 8 Plus

    Maarten - Antwoord

  40. iPhone 7 Vervanging van de aan-/uitknop: stap 40, afbeelding 1 van 1
    Gereedschap gebruikt in deze stap:
    iFixit Precision 4 mm Screwdriver Bit
    $2.99
    Koop
    • Verwijder de volgende schroeven:

    • Eén 1.4 mm lange Phillips schroef

    • Drie 2.2 mm lange standoff schroeven

    • Standoff schroeven kun je het beste verwijderen met een iPhone Standoff-schroevendraaierbitje en een bijbehorende schroevendraaier.

    • In het ergste geval zou het ook met een platkopschroevendraaier moeten lukken—maar wees in dat geval extra voorzichtig en zorg ervoor dat je niet uitschiet en daarbij omringende onderdelen beschadigt.

    Link may be missing or broken!

    Standoff screws are best removed using an [linked product missing or disabled: IF145-343-1] and driver handle.

    Phrase Neither - Antwoord

  41. iPhone 7 Vervanging van de aan-/uitknop: stap 41, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 41, afbeelding 2 van 2
    • Gebruik de punt van een spudger om het uitwerpmechanisme van de SIM-kaart uit de weg te halen van het logic board.

  42. iPhone 7 Vervanging van de aan-/uitknop: stap 42, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 42, afbeelding 2 van 2
    • Gebruik het platte eind van een spudger om het logic board, aan de kant van de batterijaansluiting, op voorzichtige wijze omhoog te tillen.

    • Zorg dat je het logic board niet per ongeluk tegen een kabel aantrekt. Als je enige vorm van weerstand voelt, check dan of alle kabels, aansluitingen en onderdelen uit de weg van het logic board zijn gehaald.

  43. iPhone 7 Vervanging van de aan-/uitknop: stap 43, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 43, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 43, afbeelding 3 van 3
    • Til het logic board, aan de kant van de batterijaansluiting, omhoog en trek deze vervolgens weg uit de achterste behuizing.

    • Wees voorzichtig dat je geen kabels meeneemt bij deze stap, dit kan zowel de kabels als het logic board beschadigen.

    Très bien pour ces étapes

    Théophile Bita - Antwoord

  44. iPhone 7 Vervanging van de aan-/uitknop, Stroom- en volumecontrolekabel: stap 44, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop, Stroom- en volumecontrolekabel: stap 44, afbeelding 2 van 2
    • Verwijder de volgende Phillips schroeven:

    • Twee 1.9 mm lange schroeven die de aan-/uitknop bevestigen.

    • Drie 2.3 mm lange schroeven die de volumeknoppen bevestigen.

    You need to remove the battery first.

    Jasper Shemilt - Antwoord

  45. iPhone 7 Vervanging van de aan-/uitknop: stap 45, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 45, afbeelding 2 van 2
    • Verwijder de volgende 1.3 mm lange Phillips schroeven:

    • Eén schroef naast de naar achteren gerichte camera

    • Eén schroef in de achterste behuizing

  46. iPhone 7 Vervanging van de aan-/uitknop: stap 46, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 46, afbeelding 2 van 2
    • Duw, vanaf de buitenkant, de luid-/stilteknop naar binnen met de punt van een spudger.

    • Dit zal de schakelaar en bijbehorende pakking losmaken van de achterste behuizing.

  47. iPhone 7 Vervanging van de aan-/uitknop: stap 47, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 47, afbeelding 2 van 2
    • Gebruik een pincet om de naar achteren gerichte camera te verwijderen.

  48. iPhone 7 Vervanging van de aan-/uitknop: stap 48, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 48, afbeelding 2 van 2
    • Gebruik een openingsplectrum om, beginnend vanaf de kant van de aan-/uitknop, de lijm die de flexkabel van de antenne aan de achterste behuizing bevestigt los te maken.

  49. iPhone 7 Vervanging van de aan-/uitknop: stap 49, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 49, afbeelding 2 van 2
    • Steek de punt van je openingsplectrum onder de flexkabel van de antenne, schuif deze richting de bovenkant van de telefoon en snijd daarbij de lijm ertussen door.

  50. iPhone 7 Vervanging van de aan-/uitknop: stap 50, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 50, afbeelding 2 van 2
    • Gebruik een pincet om de flexkabel van de antenne weg te te duwen van de zijkant van de telefoon, daarbij ruimte makend voor de schroefbeugel van de achterste behuizing.

    • Verwijder de flexkabel van de antenne.

  51. iPhone 7 Vervanging van de aan-/uitknop: stap 51, afbeelding 1 van 1
    Gereedschap gebruikt in deze stap:
    iFixit Precision Bit Driver, Aluminum
    $9.99
    Koop
    • Verwijder de 2.3 mm lange standoff schroef die de beugel van de flits aan de achterste behuizing bevestigt.

    • Standoff schroeven kun je het beste verwijderen met behulp van een iPhone Standoff schroevendraaierbitje en een bijbehorende schroevendraaier.

    • Met een platkopschroevendraaier zou het ook moeten lukken—maar wees in dat geval extra voorzichtig en zorg ervoor dat je niet wegschiet en daarmee omringende onderdelen beschadigt.

  52. iPhone 7 Vervanging van de aan-/uitknop: stap 52, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 52, afbeelding 2 van 2
    • Verwijder de beugel van de flits.

  53. iPhone 7 Vervanging van de aan-/uitknop: stap 53, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 53, afbeelding 2 van 2
    • Gebruik de punt van een spudger om de flitsmodule op voorzichtige wijze los te krijgen.

  54. iPhone 7 Vervanging van de aan-/uitknop: stap 54, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 54, afbeelding 2 van 2
    • Gebruik het mesje van de Halberd-spudger om de lijm die de microfoon aan de achterste behuizing bevestigt, los te snijden.

  55. iPhone 7 Vervanging van de aan-/uitknop: stap 55, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 55, afbeelding 2 van 2
    • Vouw de aan-/uitknopmodule weg van de zijkant van de achterste behuizing.

  56. iPhone 7 Vervanging van de aan-/uitknop: stap 56, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 56, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 56, afbeelding 3 van 3
    • Steek het mesje van een Halberd-spudger onder de kabel van de aan-/uitknop, aan de kant van de aan-/uitknop, om ook hier de lijm van de achterste behuizing te scheiden.

    • Verwijder ook verdere lijm door het mesje richting de bovenkant van de telefoon te schuiven.

  57. iPhone 7 Vervanging van de aan-/uitknop: stap 57, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 57, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 57, afbeelding 3 van 3
    • Schuif de halberd-spudger onder de kabel van de aan-/uitknop en volumeknoppen.

    • Schuif je spudger wel langzaam om ervoor te zorgen dat je de kabel tijdens het proces niet beschadigt.

  58. iPhone 7 Vervanging van de aan-/uitknop: stap 58, afbeelding 1 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 58, afbeelding 2 van 3 iPhone 7 Vervanging van de aan-/uitknop: stap 58, afbeelding 3 van 3
    • Schuif de halberd-spudger onder het deel van de kabel dat de volumeknoppen aanstuurt.

    • Schuif het mesje voorzicht onder de kabel in de richting van de onderkant van de telefoon en scheid daarbij de lijm die nog rest.

  59. iPhone 7 Vervanging van de aan-/uitknop: stap 59, afbeelding 1 van 1
    • Verwijder de kabel van de aan-/uitknop en de volumeknoppen.

    Thank you very much for this guide, I did the job perfectly, without this guide I would not have succeeded.

    Thanks thanks thanks :-)

    agibru - Antwoord

  60. iPhone 7 Vervanging van de aan-/uitknop, Aan-/uitknop: stap 60, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop, Aan-/uitknop: stap 60, afbeelding 2 van 2
    • Trek de klemmen in de richting van de onderkant van de telefoon en til deze op om deze uit de klem los te krijgen.

  61. iPhone 7 Vervanging van de aan-/uitknop: stap 61, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 61, afbeelding 2 van 2
    • Verwijder de klip van de achterste behuizing.

  62. iPhone 7 Vervanging van de aan-/uitknop: stap 62, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 62, afbeelding 2 van 2
    • Duw de onderkant van het aan-/uitknopplaatje los van de pin die het bevestigt.

    Step 89: helps to push the Power/Lock Button in while using the spudger. Otherwise, the bracket may get caught under the rim of the case.

    Mike - Antwoord

    good one mike! that helps alot. you need to use a little bit of force to lift up the right hand side ..towards bottom of phone..

    ANDREW -

    In my opinion its better to use a flat ended screw driver as it requires quite a bit of force to get these out. they clip in and clip out. when re attaching listen for the click sound so you know its located well.

    ANDREW - Antwoord

    I was having great difficulty on this step with this step with spudgers, flat head screwdrivers, etc. After much struggle I tried hooking the curved end of a Halberd Spudger, and it worked immediately with little effort.

    TL;DR - Hook a Halberd Spudger under the bottom right edge and gently pry.

    Trevor Picard - Antwoord

  63. iPhone 7 Vervanging van de aan-/uitknop: stap 63, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 63, afbeelding 2 van 2
    • Trek het plaatje los van de achterste behuizing.

  64. iPhone 7 Vervanging van de aan-/uitknop: stap 64, afbeelding 1 van 2 iPhone 7 Vervanging van de aan-/uitknop: stap 64, afbeelding 2 van 2
    • Gebruik de punt van een spudger om de aan-/uitknop uit de achterste behuizing te duwen.

    • Verwijder de aan-/uitknop.

    arrivé jusqu’ici pour nettoyer mon bouton on/off. merci pour ce tutoriel

    Flavien - Antwoord

Conclusie

Om je toestel weer in elkaar te zetten, volg je deze instructies in omgekeerde volgorde.

21 andere personen hebben deze handleiding voltooid.

Met dank aan deze vertalers:

en nl

100%

Thomas Keulemans helpt ons de wereld te herstellen! Wil je bijdragen?
Begin met vertalen ›

Scott Havard

Lid sinds: 06/27/16

49.564 Reputatie

31 handleidingen geschreven

3 opmerkingen

Alright so quick question…….

the clip shown in step 57 the one that resembles a staple,is this necessary?

Im doing a housing swap for myself and I cannot get these back on going on an hour now my hands are huge so im wondering if everything will be okay if I don’t replace these.(normally if it were another person’s device I would never take a shortcut,Never have and Never will in fact I despise this,but it’s my phone so it’s cool).

thanks

Vegeta Barrett - Antwoord

I can't see a response. Are the clips necessary?

Martha Brewer - Antwoord

It is probably to keep it in place, so I think it’s not necessary but recommended

Ward Morren - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 9

Afgelopen 7 dagen: 48

Afgelopen 30 dagen: 262

Altijd: 58,285