Deze versie kan foutieve bewerkingen bevatten. Schakel over naar de recentste gecontroleerde momentopname.
Wat je nodig hebt
-
Deze stap is niet vertaald. Help het te vertalen
-
Power off your iPhone before beginning disassembly.
-
Remove the two 3.6 mm Pentalobe P2 screws next to the dock connector.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Push the rear panel toward the top edge of the iPhone.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Pull the rear panel away from the back of the iPhone, being careful not to damage the plastic clips attached to the rear panel.
-
Remove the rear panel from the iPhone.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the following screws securing the battery connector to the logic board:
-
One 1.7 mm Phillips screw
-
One 1.5 mm Phillips screw
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Carefully push the pressure contact away from the battery connector until it slides free from its position.
-
Remove the pressure contact.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a plastic opening tool to gently pry up the battery connector from its socket on the logic board.
-
Place the tip of the tool between the loudspeaker enclosure and the metal cover of the connector, and lift the bottom edge of the connector first.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Insert the edge of a plastic opening tool between the battery and the outer case near the bottom of the iPhone.
-
Run the plastic opening tool along the right edge of the battery and pry up at several points to completely separate it from the adhesive securing it to the outer case.
-
Wait about one minute for the alcohol solution to weaken the adhesive.
-
Use the flat end of a plastic opening tool to gently lift the battery.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the exposed clear plastic pull tab to peel the battery off the adhesive securing it to the iPhone.
-
Remove the battery.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the following screws securing the dock connector cable cover to the logic board:
-
One 1.5 mm Phillips screw
-
One 1.2 mm Phillips screw
-
Remove the metal dock connector cable cover.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the edge of a plastic opening tool to pry the dock cable up from its socket on the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Peel the dock connector cable off the adhesive securing it to the logic board and the side of the speaker enclosure.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the edge of a plastic opening tool to pry the cellular antenna cable up from its socket on the logic board.
-
De-route the cellular antenna cable out from under the metal fingers attached to the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the following four screws securing the cable cover to the logic board:
-
One 2.7 mm Phillips screw
-
One 2.6 mm Phillips screw
-
One 1.3 mm Phillips screw
-
One 1.2 mm Phillips screw
-
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the edge of a plastic opening tool to pry the cable cover tabs out of their slots cut into the EMI shield on the logic board.
-
Lift the cable cover from its edge nearest the top and remove it from the iPhone.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the edge of a plastic opening tool to pry the rear camera connector up from its socket on the logic board.
-
Remove the rear camera from the iPhone.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a SIM eject tool or a paperclip to eject the SIM and its tray.
-
Remove the SIM and its tray.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the five cables near the top of the logic board in the following order:
-
Headphone jack/volume button cable
-
Front facing camera cable
-
Digitizer cable
-
Display data cable
-
Power button cable (located underneath the headphone jack/volume button cable as shown in the second picture.)
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the 1.5 mm Phillips screw securing the grounding clip to the logic board near the headphone jack.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the tip of a spudger to pry the small grounding clip up off the logic board.
-
Carefully grasp the grounding clip and remove it from the iPhone.
-
-
Deze stap is niet vertaald. Help het te vertalen
Gereedschap gebruikt in deze stap:Standoff Screwdriver for iPhones$5.49-
Remove the 4.8 mm standoff screw near the headphone jack.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the edge of a plastic opening tool to disconnect the Wi-Fi antenna from the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
If present, peel the piece of black tape covering the hidden screw near the power button.
-
Remove the 2.6 mm Phillips screw securing the logic board near the power button.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the following screws securing the logic board to the case:
-
One 2.5 mm Phillips screw near the vibrator motor
-
One 2.4 mm Phillips screw
-
One 3.6 mm standoff along the side of the logic board nearest the battery opening.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Carefully lift the logic board from the end closest to the speaker enclosure and slide it away from the top edge of the iPhone.
-
Remove the logic board.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Wedge the plastic opening tool between the vibrator and the side of the iPhone.
-
Pry the vibrator up to release it from the adhesive securing it to the iPhone.
-
Remove the vibrator.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the two 2.4 mm Phillips screws from the sides of the speaker enclosure assembly.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the small plastic bracket that was installed under the screw closest to the dock connector cable.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the speaker enclosure assembly from the iPhone.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the small pieces of black tape covering the display mounting tabs.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the 1.5 mm Phillips screw securing the display assembly near the power button.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the 1.5 mm Phillips screw near the headphone jack.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the 1.5 mm Phillips screw near the lower microphone.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the 1.5 mm Phillips screw near the dock connector cable.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Loosen the three large-headed Phillips screws along the volume button side of the iPhone about one half turn.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Loosen the three large-headed Phillips screws along the other side of the iPhone about one half turn.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use the edge of a plastic opening tool to gently pry up the display assembly around its perimeter.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remember to switch the home button from your old display to the new display (in most cases, this is not provided). The home button gasket is thin rubber, so care must be taken not to tear it. Also, check that the mesh for the speaker hole is present in the replacement; if not, move it over from the old display.
-
Be sure to peel off the protective backing (usually blue or pink) from the new panel before installing it.
-
If your replacement display does not come with a 7 mm clear plastic ring surrounding the front-facing camera, be sure to transfer it between the old and new display.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Carefully straighten the digitizer and LCD data cables, and feed them through the slot cut in the outer case.
-
This photo shows the display assembly being installed incorrectly, with too much slack in the digitizer cable, which then forms a bend/loop that gets caught in the slot. The third photo also shows this loop.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
During reassembly, do not touch the metallic area at the base of the LCD data cable, as this can cause problems with the LCD. If you do touch it accidentally, clean it gently with an alcohol wipe before continuing.
-
After reassembly, protect your new display from any scratches by installing a new screen protector.
-
Annuleren: ik heb deze handleiding niet afgemaakt.
2740 andere personen hebben deze handleiding voltooid.
162 opmerkingen
Helpfull tip... I printed these instructions and then taped each screw to the spot in the instructions with scotch tape.
AWESOME guide - very impressed. All works but I did wind up with an extra part so I must've improved upon Apple's design. The part is a small, rectangular grounding clip (black and gold) with a single brass finger and a hole through the black part... this is NOT the one mentioned in Step 26. Not sure from where it came off & not inclined to dig back into it - but would love to know where it was from. It's 1:30 am here and I may be overlooking something idiotic... any help would be much appreciated. Thanks again, Jim
Turns out my "extra" part was the one that James Molyneux mentioned, which comes out as part of Step 5. (The clip provides a bit of extra ground contact between the back of the WiFi antenna and the rear case.) Again, totally awesome instructions - thanks!