Ga door naar hoofdinhoud

Deze handleiding heeft recentere wijzigingen. Schakel over naar de nieuwste niet-geverifieerde versie.

iPhone 11 SIM Card Reader Replacement

Wat je nodig hebt

  1. iPhone 11 SIM Card Reader Replacement, Remove the pentalobe screws: stap 1, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Remove the pentalobe screws: stap 1, afbeelding 2 van 2
    • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

    • Power off your iPhone before beginning disassembly.

    • Remove the two 6.7 mm-long pentalobe screws at the bottom edge of the iPhone.

    • Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

    the right screws wouldn’t come off

    Yusef San Inocencio - Antwoord

    ok one came of but my right wont come of either!!!!

    Aisa Jawara -

    Hello guys, I still haven't found away to power off the iphone without using the screen. Cheers!

    danielaguirre93 - Antwoord

    You can try this.

    Quickly Press and release the volume up button.

    then Quickly Press and release the volume down button.

    then press and hold the power button and wait until it turns off.

    worked for me :D

    Benóný Egilson - Antwoord

    Where does one get replacement seals? Is this the same as the display assembly adhesive?

    Brian Baker - Antwoord

    not of the screwdrivers i have seem to be able to turn the screws

    Aisa Jawara - Antwoord

  2. iPhone 11 SIM Card Reader Replacement, Tape over any cracks: stap 2, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement, Tape over any cracks: stap 2, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement, Tape over any cracks: stap 2, afbeelding 3 van 3
    • If your iPhone has a cracked screen, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.

    • Lay overlapping strips of clear packing tape over the iPhone's screen until the whole face is covered.

    • Wear safety glasses to protect your eyes from any glass shaken free during the repair.

    • If you can't get the suction cup to stick in the next few steps, fold a strong piece of tape (such as duct tape) into a handle and lift the screen with that instead.

    • If all else fails, you can superglue the suction cup to the screen.

  3. iPhone 11 SIM Card Reader Replacement, Anti-Clamp instructions: stap 3, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement, Anti-Clamp instructions: stap 3, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement, Anti-Clamp instructions: stap 3, afbeelding 3 van 3
    Gereedschap gebruikt in deze stap:
    Anti-Clamp
    $24.95
    Koop
    • The next three steps demonstrate the Anti-Clamp, a tool we designed to make the opening procedure easier. If you aren't using the Anti-Clamp, skip down three steps for an alternate method.

    • For complete instructions on how to use the Anti-Clamp, check out this guide.

    • Pull the blue handle backwards to unlock the Anti-Clamp's arms.

    • Slide the arms over either the left or right edge of your iPhone.

    • Position the suction cups near the bottom edge of the iPhone—one on the top, and one on the bottom.

    • Squeeze the cups together to apply suction to the desired area.

    • If you find that the surface of your iPhone is too slippery for the Anti-Clamp to hold onto, you can use tape to create a grippier surface.

  4. iPhone 11 SIM Card Reader Replacement: stap 4, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement: stap 4, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement: stap 4, afbeelding 3 van 3
    • Pull the blue handle forward to lock the arms.

    • Turn the handle clockwise 360 degrees or until the cups start to stretch.

    • Make sure the suction cups remain aligned with each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms.

  5. iPhone 11 SIM Card Reader Replacement: stap 5, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement: stap 5, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement: stap 5, afbeelding 3 van 3
    • Heat an iOpener and thread it through the arms of the Anti-Clamp.

    • You can also use a hair dryer, heat gun, or hot plate—but extreme heat can damage the display and/or internal battery, so proceed with care.

    • Fold the iOpener so it lays on the bottom edge of the iPhone.

    • Wait one minute to give the adhesive a chance to release and present an opening gap.

    • Insert an opening pick into the gap under the screen and the plastic bezel, not the screen itself.

    • If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle a quarter turn.

    • Don't crank more than a quarter turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the work for you.

    • Skip the next three steps.

  6. iPhone 11 SIM Card Reader Replacement, Heat the lower edge of the phone: stap 6, afbeelding 1 van 1
    • Heating the lower edge of the iPhone helps soften the adhesive securing the display, making it easier to open.

    • Use a hairdryer or heat gun or prepare an iOpener and apply it to the lower edge of the iPhone for about a minute.

  7. iPhone 11 SIM Card Reader Replacement: stap 7, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement: stap 7, afbeelding 2 van 2
    • If you're using a single suction handle, apply it to the bottom edge of the phone, while avoiding the curved portion of the glass.

  8. iPhone 11 SIM Card Reader Replacement, Lift the display slightly: stap 8, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement, Lift the display slightly: stap 8, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement, Lift the display slightly: stap 8, afbeelding 3 van 3
    • Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.

    • Insert an opening pick into the gap under the screen and the plastic bezelnot the screen itself.

    • The watertight adhesive holding the display in place is very strong; creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your tool.

    This turned out to be the most difficult part for me. My old ifixit suction cup didn't suck hard enough to generate enough force to pry the display from the case. I ended up applying heat at least a dozen times, and I had to pull up on the suction cup forcefully over and over and over while repositioning it several times. I finally had success inserting my pick into the tiny gap after 30 or so rapid tugs on the suction cup.

    matthew r - Antwoord

    I pulled the screen by accident instead of the bottom layer, now what?

    Alvaro - Antwoord

    I have the same question

    Konstantinos Solakoglou -

  9. iPhone 11 SIM Card Reader Replacement, Separate the screen adhesive: stap 9, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement, Separate the screen adhesive: stap 9, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement, Separate the screen adhesive: stap 9, afbeelding 3 van 3
    • Slide the opening pick around the lower left corner and up the left edge of the iPhone, slicing through the adhesive holding the display in place.

    • Don't insert your pick more than 3 mm, as you may damage internal components.

  10. iPhone 11 SIM Card Reader Replacement, Screen information: stap 10, afbeelding 1 van 1
    • There are delicate cables along the right edge of your iPhone. Don't insert your pick here, as you may damage the cables.

  11. iPhone 11 SIM Card Reader Replacement: stap 11, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement: stap 11, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement: stap 11, afbeelding 3 van 3
    • Re-insert your pick at the bottom edge of the iPhone, and slide it up the right side to continue separating the adhesive.

    • Don't insert your pick more than 3 mm, as you may damage the display cables.

    Instructions are confusing as the last step says not to insert at certain points, while this says to slide all the way up the right side - is it that sliding is ok but inserting isn't (whatever that might mean) or just not more than 3mm?

    Peter Hill - Antwoord

    Just slide slightly and the display will rise without problems on all iPhone models, sometimes if I have long nails I even insert a fingernail and lift the display.

    Tonynox -

  12. iPhone 11 SIM Card Reader Replacement: stap 12, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement: stap 12, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement: stap 12, afbeelding 3 van 3
    • The top edge of the display is secured with both glue and clips.

    • Gently pull the right edge of the display down slightly (in the direction of the Lightning port).

    • Insert your pick into the top-right corner of the phone.

  13. iPhone 11 SIM Card Reader Replacement: stap 13, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement: stap 13, afbeelding 2 van 2
    • Continue pulling the display down (toward the Lightning port) as needed in order to make a gap large enough for the pick.

    • Slide the pick to the top left corner and cut any remaining adhesive securing the display.

    • Don't insert your pick more than 3 mm, as you may damage the Face ID sensor array.

  14. iPhone 11 SIM Card Reader Replacement, Remove the suction cup: stap 14, afbeelding 1 van 1
    • Pull the small nub on the suction cup to detach it from the front panel.

  15. iPhone 11 SIM Card Reader Replacement, Open the iPhone: stap 15, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement, Open the iPhone: stap 15, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement, Open the iPhone: stap 15, afbeelding 3 van 3
    • Open the iPhone by swinging the display up from the left side, like the back cover of a book.

    • Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.

    • Prop the display up against something sturdy.

    • During reassembly, lay the display in position, align the clips along the top edge, and carefully press the top edge into place before snapping the rest of the display down. If it doesn't click easily into place, check the condition of the clips around the perimeter of the display and make sure they aren't bent.

  16. iPhone 11 SIM Card Reader Replacement, Display Assembly: stap 16, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Display Assembly: stap 16, afbeelding 2 van 2
    • To access the screws in the following step, tilt the display by slightly lifting its lower edge.

    • Be careful not to strain or tear the display cables.

  17. iPhone 11 SIM Card Reader Replacement, Unscrew the battery connector cover: stap 17, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Unscrew the battery connector cover: stap 17, afbeelding 2 van 2
    Gereedschap gebruikt in deze stap:
    Magnetic Project Mat
    $19.95
    Koop
    • Use a Y000 driver to remove the three 1.1 mm-long screws securing the battery connector bracket.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

    • During reassembly, this is a good point to power on your iPhone and test all functions before you seal the display in place. Be sure to power your iPhone back down completely before you continue working.

    During reassembly, I had to connect my phone to the charger before it would power up.

    Austin Culberson - Antwoord

    Die Schrauben sind wahnsinnig kurz, tatsächlich winzig klein. Nach dem Herausdrehen könnte es im ersten Moment so aussehen, als habe man die Schrauben ausgebohrt anstatt herauszudrehen, sie sind jedoch sehr schnell gelöst und liegen dann entweder im Gehäuse oder sind neben dem Gehäuse herausgefallen. In jedem Fall sollten sie nie auf den Boden fallen, da sie dann kaum mehr auffindbar wären.

    Bernd Sonneck - Antwoord

  18. iPhone 11 SIM Card Reader Replacement, Remove the battery connector cover: stap 18, afbeelding 1 van 1
    • Remove the bracket.

  19. iPhone 11 SIM Card Reader Replacement, Disconnect the battery: stap 19, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Disconnect the battery: stap 19, afbeelding 2 van 2
    • Use a spudger or a clean fingernail to pry the battery connector up from its socket on the logic board.

    • Try not to damage the black silicone seal surrounding this and other board connections. These seals provide extra protection against water and dust intrusion.

    • Bend the connector slightly away from the logic board to prevent it from accidentally contacting the socket.

  20. iPhone 11 SIM Card Reader Replacement, Unscrew the logic board cover screws: stap 20, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Unscrew the logic board cover screws: stap 20, afbeelding 2 van 2
    • Use a Y000 driver to remove the five 1.1 mm screws securing the logic board cover bracket.

    Die Schrauben sind wahnsinnig kurz, tatsächlich winzig klein. Nach dem Herausdrehen könnte es im ersten Moment so aussehen, als habe man die Schrauben ausgebohrt anstatt herauszudrehen, sie sind jedoch sehr schnell gelöst und liegen dann entweder im Gehäuse oder sind neben dem Gehäuse herausgefallen. In jedem Fall sollten sie nie auf den Boden fallen, da sie dann kaum mehr auffindbar wären.

    Bernd Sonneck - Antwoord

  21. iPhone 11 SIM Card Reader Replacement, Remove the logic board cover bracket: stap 21, afbeelding 1 van 1
    • Remove the bracket.

  22. iPhone 11 SIM Card Reader Replacement, Disconnect the display: stap 22, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement, Disconnect the display: stap 22, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement, Disconnect the display: stap 22, afbeelding 3 van 3
    • Use a spudger or a fingernail to disconnect the LCD panel cable connector.

    • Disconnect the digitizer connector next to it.

    Be mindful when reconnecting LCD panel connector and digitizer connector. It’s looks very similar. These 2 ribbon connectors a slightly different.

    Pay attention.

    Josmaknolavic - Antwoord

    내 아이폰이 디스플레이 분리 단계를 거친 후, 전원이 들어오지 않습니다. 층전기를 꽂아도 배터리에 미세한 전기 반응이 느껴지지 않고, 탭틱 엔진도 작동하지 않게 되었습니다. cpu 온도는 여전히 뜨껍습니다. 내 마더보드가 디스플레이 분리 후 갑자기 고장난건가요?

    Protoncal - Antwoord

    Hast Du das Problem gelöst?

    Bernd Sonneck -

  23. iPhone 11 SIM Card Reader Replacement, Disconnect the front sensors: stap 23, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Disconnect the front sensors: stap 23, afbeelding 2 van 2
    • Use the point of a spudger or a fingernail to disconnect the front panel sensor assembly connector.

  24. iPhone 11 SIM Card Reader Replacement, Remove the display assembly: stap 24, afbeelding 1 van 1

    After this step its probably a good idea to test the new screen (you dont have to plug in the front camera assembly)

    Richard Kraus - Antwoord

    Not a technician, so correct me if I'm wrong: I think that it's at this step of reassembly (before you reattach the screen) that you apply waterproof glue, if you have it.

    Athanasius Pernath - Antwoord

  25. iPhone 11 SIM Card Reader Replacement, Disconnect the Lightning port flex cable: stap 25, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Disconnect the Lightning port flex cable: stap 25, afbeelding 2 van 2
    • Use a spudger or a fingernail to pry up and disconnect the flex cable for the Lightning connector assembly.

  26. iPhone 11 SIM Card Reader Replacement, Remove three Phillips screws: stap 26, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement, Remove three Phillips screws: stap 26, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement, Remove three Phillips screws: stap 26, afbeelding 3 van 3
    • Remove the three Phillips screws surrounding the SIM card reader:

    • One 1.5 mm screw

    • One 1.9 mm screw

    • One 1.6 mm screw securing a grounding bracket

    • Removing the grounding bracket secured by the final screw.

  27. iPhone 11 SIM Card Reader Replacement, Remove the standoff screw: stap 27, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Remove the standoff screw: stap 27, afbeelding 2 van 2
    • Use a standoff driver to remove the 3.1 mm screw securing the SIM card reader connector bracket.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage nearby components.

  28. iPhone 11 SIM Card Reader Replacement, Remove the SIM reader's connector bracket: stap 28, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Remove the SIM reader's connector bracket: stap 28, afbeelding 2 van 2
    • Remove the SIM reader's connector bracket.

  29. iPhone 11 SIM Card Reader Replacement, Disconnect the SIM card reader: stap 29, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Disconnect the SIM card reader: stap 29, afbeelding 2 van 2
    • While gently lifting the Lightning connector flex cable out of the way, use the point of a spudger to pry up and disconnect the SIM card reader flex cable.

  30. iPhone 11 SIM Card Reader Replacement, Push the SIM eject plunger aside: stap 30, afbeelding 1 van 2 iPhone 11 SIM Card Reader Replacement, Push the SIM eject plunger aside: stap 30, afbeelding 2 van 2
    • Use the point of a spudger to push the SIM eject plunger out towards the edge of the phone.

  31. iPhone 11 SIM Card Reader Replacement, Remove the SIM reader: stap 31, afbeelding 1 van 3 iPhone 11 SIM Card Reader Replacement, Remove the SIM reader: stap 31, afbeelding 2 van 3 iPhone 11 SIM Card Reader Replacement, Remove the SIM reader: stap 31, afbeelding 3 van 3
    • Lift the SIM card reader and slide it toward the outside edge of the iPhone.

    • Remove the SIM card reader.

Conclusie

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our iPhone 11 Answers community for help.

17 andere personen hebben deze handleiding voltooid.

Jeff Suovanen

Lid sinds: 08/06/13

427.129 Reputatie

259 handleidingen geschreven

Team

iFixit Lid van iFixit

Staff

136 Leden

16.578 handleidingen geschreven

10 opmerkingen

Puedo cambiar una single SIM tray por una dual SIM tray?

Gracias

Overth Castellanos - Antwoord

Helpful guide as always! I will note, I get a “SIM Failure” message after completing this repair.. It works properly but the message pops up (multiple times) on a reboot. Potentially a low quality part? I’ve only done this once so I can’t say if this is a common issue.

cheers!

Andrew - Antwoord

Hello,

It could be a low quality part, if you can found, try with a genuine parts, maybe removed from a broken iPhone.

Cheers :)

jacopo -

can I change a single SIM card reader for a dual SIM card reader on my iPhone 11?

josealejandro94 - Antwoord

We haven’t tested this yet (we will!) but internet sources seem to point towards yes!

Arthur Shi -

I have done this successfully also. Thank you for your guide.

Now, I am planning to do it on an iPhone 11 Pro. Is it possible?

Dennis Capulong - Antwoord

Why does my iphone 11 pro max turn off after sim slot replamcemnt

Dulce Pacheco - Antwoord

Hello..is there a connection if my sim reader is broken,i also cannot activated my iphone 11?

Romero Kuduro - Antwoord

Alguien me puede ayudar por favor mi celular no agarra el ship y todo da perfectamente es un iPhone 11 que puedo hacer gracias se los agradecería mucho saludos desde Londres Inglaterra muchas bendiciones

Jorge Alfonso Viera Zavala - Antwoord

Tengo un iPhone 11 y no agarra la targeta sin( el Ship )me pueden ayudar por favor favor saludos muchas bendiciones a cada uno

Jorge Alfonso Viera Zavala - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 14

Afgelopen 7 dagen: 185

Afgelopen 30 dagen: 772

Altijd: 34,143