Inleiding

The metallic bottom shield protects the logic board from electromagnetic interference.

Use a coin to rotate the battery locking screw 90 degrees clockwise.
  • Use a coin to rotate the battery locking screw 90 degrees clockwise.

Voeg opmerking toe

Lift the battery out of the computer.
  • Lift the battery out of the computer.

Voeg opmerking toe

  • Use a pin (or anything you like) to remove the three rubber feet from the lower case.

Voeg opmerking toe

  • Remove the three newly-revealed Phillips screws.

Voeg opmerking toe

  • Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.

Voeg opmerking toe

  • Remove the three hex screws using a T8 Torx screwdriver (or Allen screws using an Allen key if these are used).

  • The shorter screw is in the center of the computer.

Why use a T8 Torx when these screws are metric hex 2? The T8 didn't work at all. Other than that this was a very easy repair. It cost $29 instead of the $150 that I paid the last time a Mac shop made the same repair.

dalekaty - Antwoord

来自 dalekaty 的话:

Why use a T8 Torx when these screws are metric hex 2? The T8 didn't work at all. Other than that this was a very easy repair. It cost $29 instead of the $150 that I paid the last time a Mac shop made the same repair.

Had the same issue with a T8, although I blamed that on my T8 being quite stripped. Finding an appropriate bit was quite a challenge... but I'm pretty certain a T8 isn't correct. The screws have a hex head, not a Torx... maybe T8 is the closest thing that tends to fit...

Matt Falcon - Antwoord

The screw on the left wasnt able to get tight for some reason

Helena - Antwoord

Not Torx, but allen key (British wrench), 2mm

alicelittle - Antwoord

I attempted this last night following all the steps correctly, when I was done my ibook would not turn on. Now sure where I went wrong? Any ideas. Thank you

stefanienikole - Antwoord

  • Remove the two Phillips screws on either side of the battery contacts.

Voeg opmerking toe

  • Breathe deeply. Trying times are ahead, but we promise the lower case does come off.

  • Push the thin rims of the lower case surrounding the battery compartment in, bending them past the tabs, and then lift up to free that corner of the lower case.

I printed these instructions out, and this one was at the top of page 2. I found the first paragraph amusing enough that I had to show my boss.

Kristoffer Bisher - Antwoord

  • There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.

  • Be careful not to break this clip!

Voeg opmerking toe

  • Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.

Voeg opmerking toe

  • Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.

For me, this was really the toughest part! Trying to find/get a good grip on the iBook and really *forcing* that spudger around. All without scratching the display.

bccreative - Antwoord

Once you loosen the the front the seam is very tight. I was able to slide the spudger in the middle of the port side instead of starting at the corner.

Robert Oliver - Antwoord

  • There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.

Voeg opmerking toe

  • Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free (it may be helpful to jiggle the case up and down).

This was the scariest part for me. I had to wiggle it a lot as it seemed to be stuck. But it did come loose.

Robert Oliver - Antwoord

  • Remove the small greasy springs with white plastic caps from either side of the battery contacts.

Voeg opmerking toe

  • Remove the following 10 screws from the bottom shield:

    • Six 3 mm Phillips

    • Three 7.5 mm Phillips

    • One 14 mm Phillips

My 1 GHz iBook G4 only had the two 7.5 mm Phillips on the right and the two 3 mm Phillips above the battery compartment.

geekspeak - Antwoord

  • Lift the bottom shield off.

The front of the foil cover has a lip divided into four separate tabs. Use a blade to loosen each as they can be easily bent.

geekspeak - Antwoord

My dc board had 2 screws. for some reason when i tried to screw them both back in only one got tight. the other one just kept twirling so i left it out. i didnt want to have a loose screw rattling around in my computer.

also had trouble laying down the wire to the dc board. it wouldnt lay flat but i was able to get it flat enough. overall it worked and the computer is now up and running!

thank you! it was pretty easy

Helena - Antwoord

Conclusie

To reassemble your device, follow these instructions in reverse order.

7 andere personen hebben deze handleiding voltooid.

Bijgevoegde documenten

iRobot

Lid sinds: 24-09-09

1 Reputatie

621 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 1

Afgelopen 30 Dagen: 2

Altijd: 5,277