Menu

Jouw instellingen

Mijn werkbank

Krijg snel toegang tot handleidingen, onderdelen en antwoorden voor jouw apparaten
Winkelwagen

Het lijkt erop dat je mandje leeg is

Doorblader onze winkel

iBook G4 12" 800 MHz-1.2 GHz Rear Display Bezel Replacement

Geschreven door: Andrew Bookholt (en 5 andere bijdragers)
  • Reacties: 0
  • Favorieten: 0
  • Voltooide reparaties: 2

Moeilijkheid

Moeilijk

Stappen

8

Tijd vereist

Stel een tijd voor??

Secties

2

Markeringen

0

Inleiding

Remove your rear display bezel to access your display's internals.

Gereedschap

Koop deze gereedschappen

Onderdelen

  1. Use a coin to rotate the battery locking screw 90 degrees clockwise.

    • Use a coin to rotate the battery locking screw 90 degrees clockwise.

    Bewerken

  2. Lift the battery out of the computer.

    • Lift the battery out of the computer.

    Bewerken

  3. Use a 1.5mm hex screwdriver to remove the two hex screws on either side of the display (four screws total). If you don't have a 1.5mm hex driver, you can probably get these screws out with a T6 Torx screwdriver. However, if you use a T6 Torx driver you'll be more likely to strip the screws.

    • Use a 1.5mm hex screwdriver to remove the two hex screws on either side of the display (four screws total).

    • If you don't have a 1.5mm hex driver, you can probably get these screws out with a T6 Torx screwdriver. However, if you use a T6 Torx driver you'll be more likely to strip the screws.

    Bewerken

  4. Koop geen nieuw model.

    Bespaar $10 op $50 met coupon
    SKIPANDSAVE10

    Bespaar nu

    Koop geen nieuw model.

    Take $10 off $50 with
    SKIPANDSAVE10

    Bespaar nu

  5. Insert the flat end of a spudger perpendicular to the face of the display into the gap between the front and rear bezels near the upper left corner of the display. Rotate the spudger away from the display to pry the rear bezel off the front bezel.

    • Insert the flat end of a spudger perpendicular to the face of the display into the gap between the front and rear bezels near the upper left corner of the display.

    • Rotate the spudger away from the display to pry the rear bezel off the front bezel.

    Bewerken

  6. Run your spudger along the top edge of the front display bezel to evenly separate the two bezels.

    • Run your spudger along the top edge of the front display bezel to evenly separate the two bezels.

    Bewerken

  7. Working down from the upper left corner, use the flat end of a spudger to pry the rear bezel away from the left edge of the display. Working down from the upper left corner, use the flat end of a spudger to pry the rear bezel away from the left edge of the display.

    • Working down from the upper left corner, use the flat end of a spudger to pry the rear bezel away from the left edge of the display.

    Bewerken

  8. Use the flat end of a spudger to pry the rear bezel away from the right edge of the display.

    • Use the flat end of a spudger to pry the rear bezel away from the right edge of the display.

    • If necessary, pry along the bottom edge of the rear bezel to separate it from the display assembly.

    Bewerken

  9. Lift the rear bezel off the display assembly.

    • Lift the rear bezel off the display assembly.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

2 andere personen hebben deze handleiding voltooid.

Bijgevoegde documenten

0 Opmerkingen

Een opmerking toevoegen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 0

Altijd: 3,896