Ga door naar hoofdinhoud

Zenithink ZTPAD ZT280 C91 Front Panel Replacement

Wat je nodig hebt

  1. Zenithink ZTPAD ZT280 C91 Front Panel Replacement, Back Panel: stap 1, afbeelding 1 van 1
    • Remove the two screws on the bottom using a Phillips #00 screwdriver.

    • For differentiation purposes, these screws are 4mm long.

  2. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 2, afbeelding 1 van 3 Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 2, afbeelding 2 van 3 Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 2, afbeelding 3 van 3
    • Using a spudger, start prying the case apart by working around the edge slowly.

    • Be careful not to damage any of the latches that hold the back panel in place, especially if you are using a metal spudger.

    • While prying, be careful to not lose the power and volume buttons; the case is the only thing holding them in place so they will easily come out once the panel has been removed

    • Be careful to not damage the speaker cables, they will still be connecting both panels.

  3. Zenithink ZTPAD ZT280 C91 Front Panel Replacement, Motherboard: stap 3, afbeelding 1 van 1
    • Peel back the touch interface chip (which is on the top right of the motherboard, covered in yellow tape.)

  4. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 4, afbeelding 1 van 1
    • Flip up the small gate and unplug the ribbon cable shown.

  5. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 5, afbeelding 1 van 1
    • Using a Phillips #00 screwdriver, remove the screws highlighted with the orange rings as shown in the picture.

    • For differentiation purposes, these screws are 3.5mm long.

  6. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 6, afbeelding 1 van 1
    • Slide back the plastic latch for the main display cable.

    • Carefully unplug the cable with tweezers.

  7. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 7, afbeelding 1 van 2 Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 7, afbeelding 2 van 2
    • Slide back the plastic latch for the camera cable.

    • Carefully unplug the cable with tweezers.

  8. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 8, afbeelding 1 van 1
    • Peel back the reflective tape.

  9. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 9, afbeelding 1 van 2 Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 9, afbeelding 2 van 2
    • Lift up the motherboard assembly, starting by lifting up the top.

    • Be careful not to damage any of the ports on the underside of the tablet.

    • The camera cable will slide through a small notch and end up underneath the board.

  10. Zenithink ZTPAD ZT280 C91 Front Panel Replacement, Front Panel: stap 10, afbeelding 1 van 1
    • Remove the four highlighted screws using a Phillips #1 screwdriver.

    • For differentiation purposes, these screws are 4mm long and have a larger head than the rest of the screws.

  11. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: stap 11, afbeelding 1 van 1
    • Starting from the top, slowly lift everything up out of the front panel.

    • Remove the front panel off of the device.

    • Be careful not to damage the ports along the bottom.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Keelie Beach

Lid sinds: 09/21/18

435 Reputatie

3 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 1

Altijd: 123