Repareer je spullen Gemeenschap Winkel

ULCO Integrus PSV ventilator O-Ring Replacement

Medische apparatuur
Noch iFixit, noch deze reparatiehandleiding worden onderschreven door of zijn gelieerd aan de fabrikant van de desbetreffende medische apparatuur.

Inleiding

This guide will serve to help access and replace the O-Ring.

Preparation to Service:

  1. Make sure that the anesthetic machine is OFF
  2. Gain access to ventilator housing from this guide here

Wat je nodig hebt

    • Before disassembly, make sure the front wheel breaks are on.

    Vertaal

    • Make sure ALL gas supplies are disconnected and the system has been purged, and make sure all electrical supplies have been disconnected.

    Vertaal

  3. Vertaal

  4. ULCO Integrus PSV ventilator O-Ring Replacement: stap 4, afbeelding 1 van 1

    • With one hand on the ventilator removal handle and one holding the lower half of the ventilator, pull up firmly on the handle so that the mounting slides up the slots in the frame.

    Vertaal

  5. ULCO Integrus PSV ventilator O-Ring Replacement: stap 5, afbeelding 1 van 1

    • Pull the ventilator housing towards you so that the mounting tabs come out of the frame slots rest the ventilator housing on the plastic skirt at the rear of the workstation as shown in the photo.

    Vertaal

  6. ULCO Integrus PSV ventilator O-Ring Replacement, O-Ring: stap 6, afbeelding 1 van 1

    • Pull out the exhaust gas tube (EV910424) and replace the O-ring in the groove on the tube and smear with silicone grease.

    Vertaal

  7. ULCO Integrus PSV ventilator O-Ring Replacement: stap 7, afbeelding 1 van 1

    • Pull out the drive gas tube (EV9104251) and replace the O-ring in the groove on the tube and smear with silicone grease.

    Vertaal

  8. ULCO Integrus PSV ventilator O-Ring Replacement: stap 8, afbeelding 1 van 1

    • Pull out the blow off gas tube (EV910426).

    Vertaal

  9. ULCO Integrus PSV ventilator O-Ring Replacement: stap 9, afbeelding 1 van 1

    • Unscrew the 12 retaining screws on the top plate. Carefully lever the top plate back taking care to ensure that none of the cables connecting it to the body of the ventilator become disconnected.

    Vertaal

  10. ULCO Integrus PSV ventilator O-Ring Replacement: stap 10, afbeelding 1 van 1

    • Using tweezers, remove the O-ring from inside the blow off gas tube receptacle on the flow block. Smear the O-ring groove with silicone grease and insert the new O-ring.

    Vertaal
Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Auteur

met 3 andere bijdragers

Preston Myers

Lid sinds: 04/09/20

493 Reputatie

4 handleidingen geschreven

Medailles: 6

+3 andere badges

Team

Cal Poly, Team S7-G13, Paton Spring 2020 Lid van Cal Poly, Team S7-G13, Paton Spring 2020

CPSU-PATON-S20S7G13

3 Leden

8 handleidingen geschreven

0 opmerkingen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 3

Altijd: 31