Ga door naar hoofdinhoud

Inleiding

If you are noticing problems with your screen, such as distortions or the entire screen going black, and have decided to replace the screen, use this guide.

Onderdelen

Geen onderdelen opgegeven.

  1. Locate the round stickers on each corner of the screen covering the screws. Use a sharp tool, such as a pointy metal spudger or tweezers, to gently remove these stickers.
    • Locate the round stickers on each corner of the screen covering the screws. Use a sharp tool, such as a pointy metal spudger or tweezers, to gently remove these stickers.

  2. Unscrew the screws using a Phillips Head #1 screwdriver; there should be four in total, one on each corner.
    • Unscrew the screws using a Phillips Head #1 screwdriver; there should be four in total, one on each corner.

  3. Take the opening tool and gently place it under the plastic framing the screen. Gently slip the opening tool between the plastic frame and the screen, until a change in pressure is felt, the feeling of the plastic clasps dislodging.
    • Take the opening tool and gently place it under the plastic framing the screen. Gently slip the opening tool between the plastic frame and the screen, until a change in pressure is felt, the feeling of the plastic clasps dislodging.

  4. Laptop batterijen

    Batterijen voor alle grote PC-merken, met onze kwaliteitsgarantie.

    Nu winkelen

    Laptop batterijen

    Batterijen voor alle grote PC-merken, met onze kwaliteitsgarantie.

    Nu winkelen
  5. Repeat this process along the interior edges of the plastic frame. Once the all plastic locks are unhooked the plastic frame should fall off the screen.
    • Repeat this process along the interior edges of the plastic frame. Once the all plastic locks are unhooked the plastic frame should fall off the screen.

  6. Locate the two screws at the bottom corners of the screen.
    • Locate the two screws at the bottom corners of the screen.

  7. Using the same screwdriver (Phillips Head #1), unscrew all the screws on both sides of the screen.
    • Using the same screwdriver (Phillips Head #1), unscrew all the screws on both sides of the screen.

  8. Find and unscrew the six screws (3 on each side) on the sides of the screen. Be careful while unscrewing the last few screws as the screen will still be attached to the computer in two different places and may fall out of its casing.
    • Find and unscrew the six screws (3 on each side) on the sides of the screen. Be careful while unscrewing the last few screws as the screen will still be attached to the computer in two different places and may fall out of its casing.

  9. At the top of the computer, there should be a cable still wired to the detached screen. Gently pull the head of the cable away from its connector until the cable dislodges.
    • At the top of the computer, there should be a cable still wired to the detached screen. Gently pull the head of the cable away from its connector until the cable dislodges.

  10. At the back of the screen, there will be one more connector at the bottom. Remove the tape to disconnect this wire.
    • At the back of the screen, there will be one more connector at the bottom. Remove the tape to disconnect this wire.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Ian M Sloop

Lid sinds: 20-10-18

667 Reputatie

4 handleidingen geschreven

Team

UC Davis, Team S7-G7, Lore Fall 2018 Lid van UC Davis, Team S7-G7, Lore Fall 2018

UCD-LORE-F18S7G7

4 Leden

4 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 2

Afgelopen 30 Dagen: 7

Altijd: 59