Ga door naar hoofdinhoud

Inleiding

This guide give instructions on how to locate the speaker for removal and/or repair.

Onderdelen

Geen onderdelen opgegeven.

  1. Flip over the phone so that the back is facing up.
    • Flip over the phone so that the back is facing up.

    • Pressing your thumb against the back cover, slide the cover off of the phone.

  2. Remove the phone's battery.
    • Remove the phone's battery.

  3. With the phone closed, run a plastic opening tool along the seam of the top half of the phone. Make sure to disconnect each of the five clips before proceeding to the next step. There are two clips on each side of the phone and one on the top.
    • With the phone closed, run a plastic opening tool along the seam of the top half of the phone.

    • Make sure to disconnect each of the five clips before proceeding to the next step.

    • There are two clips on each side of the phone and one on the top.

  4. Remove the four 3.2 mm screws from the front panel using a T6 Torx screwdriver. The fourth screw is located under a fold in the ribbon cable.
    • Remove the four 3.2 mm screws from the front panel using a T6 Torx screwdriver.

    • The fourth screw is located under a fold in the ribbon cable.

  5. Starting in the lower right corner, slowly begin to lift the tape that is holding down the front LCD and cables. Be careful around the two ribbon cables attached to the tape. These cables are fragile. Lift the tape from the board.
    • Starting in the lower right corner, slowly begin to lift the tape that is holding down the front LCD and cables.

    • Be careful around the two ribbon cables attached to the tape. These cables are fragile.

    • Lift the tape from the board.

  6. Using a plastic opening tool, lift the ribbon cable connection below the front LCD.
    • Using a plastic opening tool, lift the ribbon cable connection below the front LCD.

  7. Using a plastic opening tool, slowly pry the LCD display from the bottom, releasing it from the glue that is holding it to the board. Using a plastic opening tool, slowly pry the LCD display from the bottom, releasing it from the glue that is holding it to the board. Using a plastic opening tool, slowly pry the LCD display from the bottom, releasing it from the glue that is holding it to the board.
    • Using a plastic opening tool, slowly pry the LCD display from the bottom, releasing it from the glue that is holding it to the board.

  8. Locate the ribbon cable connection in the upper right hand corner of the board.
    • Locate the ribbon cable connection in the upper right hand corner of the board.

    • Using a plastic opening tool, lift off the cable from the board.

    • Be gentle and make sure not to rip the ribbon cable.

  9. Using a plastic opening tool, slowly work the board off the mounts holding it to the frame. Flip the board over to reveal the main display.
    • Using a plastic opening tool, slowly work the board off the mounts holding it to the frame.

    • Flip the board over to reveal the main display.

  10. Locate the ribbon cable for the main display on the bottom of the board.
    • Locate the ribbon cable for the main display on the bottom of the board.

    • Slowly lift off the ribbon connector from its housing using a plastic opening tool.

  11. Slowly wedge the plastic opening tool under the bottom of the main display. Separate the display from the glue lifting it off the board.
    • Slowly wedge the plastic opening tool under the bottom of the main display.

    • Separate the display from the glue lifting it off the board.

  12. Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.
    • Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Andrew

Lid sinds: 04-10-10

397 Reputatie

4 handleidingen geschreven

Team

Cal Poly, Team 4-46, Amido Fall 2010 Lid van Cal Poly, Team 4-46, Amido Fall 2010

CPSU-AMIDO-F10S4G46

4 Leden

14 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 uren: 0

Afgelopen 7 dagen: 0

Afgelopen 30 dagen: 1

Altijd: 492