Deze versie kan foutieve bewerkingen bevatten. Schakel over naar de recentste gecontroleerde momentopname.
Wat je nodig hebt
-
Deze stap is niet vertaald. Help het te vertalen
-
Heat the back cover of your Xperia Z3 to loosen the adhesive underneath.
-
Lift up the back cover with a suction handle and put an opening pick in the gap.
-
Move the pick carefully around the edges to loosen the adhesive on every side of the phone.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
When the edges of the cover are free from adhesive, tilt it to allow access to the battery tabs.
-
Use tweezers to pull the two black adhesive strips out of the phone but don't pull just yet.
-
-
Deze stap is niet vertaald. Help het te vertalen
Gereedschap gebruikt in deze stap:Plastic Cards$2.99-
Gently pull out both of the adhesive tabs out of the phone, parallel to the rear cover.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
After pulling out the adhesive tabs, you can lift the back cover and remove it.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Unplug the battery flex connector.
-
Use a tweezer to gently pull off the adhesive strip on the bottom part of the battery.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a spudger on the left side of the frame to lever out the battery.
-
Remove the battery.
-
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Unplug the antenna cable with a tweezer.
-
Use a Spudger to unplug the main flex connector and the flex connector of the vibration motor.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Remove the cover on top of the loudspeaker assembly.
-
Use a spudger to pull out the vibration motor and remove its rubber gasket with a tweezer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a tweezer to remove the adhesive strip of the loudspeaker assembly.
-
Pull up the metal clamp at the upper end of the loudspeaker assembly by using a tweezer and remove it.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift up the main flex cable covering the loudspeaker assembly with a Spudger
-
Lift up the whole loudspeaker assembly with a spudger and remove it.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a spudger to lift up the end of the main flex.
-
Remove the bronze foil covering the connector of the main flex with a tweezer.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Lift up the metal plate which is placed beneath the loudspeaker assembly and remove it.
-
Unplug the main flex cable.
-
Use a tweezer to remove the yellow adhesive foil covering the display flex cable.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use a spudger to gently slide beneath the display flex cable and lift it up.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
Use an iOpener to loosen the adhesive underneath the display of your phone.
-
After the adhesive at the lower end of your phone is loosened, pull up the display with your suction handle and insert an opening pick.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
After loosening the adhesive in the lower area of your phone with an opening pick, insert an other opening pick approximately 1/16 of an inch and slide it along both sides of the phone to sparate the display from the frame.
-
After loosening all the adhesive beneath the display twist the opening pick in the lower end of your phone a little bit to lift up the display.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
To fully remove the display off your phone, you need to thread the display flex cable through the gap of the mid frame in the bottom end of your phone.
-
-
Deze stap is niet vertaald. Help het te vertalen
-
If you didn't manage to keep the earpiece in its place while removing the display you have to remove it now.
-
Use an iOpener to soften the glue, then use an opening pick to slide between the the earpiece and the display and carefully take off the earpiece speaker.
-
Annuleren: ik heb deze handleiding niet afgemaakt.
37 andere personen hebben deze handleiding voltooid.
7 opmerkingen
What website is best to obtain a genuine screen and back from?
The back cover won’t fall off Josua but I would definitely recommend new adhesive!
But only for the phone to be waterproof? Because mine is definitely not waterproof anymore.. So I think this wouldn’t make any difference.
Josua -
In our case the back cover just held semi tight to the phone assembly without new adhesive. It could happen that the back cover falls off, when you pull the phone out of your pocket or you drop it. New adhesive also protects your phone from dust which can cause overheating.