Inleiding

How to remove the Ethernet port from the Sony Vaio VGN-S260 laptop

Onderdelen

Geen onderdelen nodig.

Flip the laptop over so the Vaio logo is facing down
  • Flip the laptop over so the Vaio logo is facing down

  • Locate the battery at the top and Find the release and unlock slides on the battery

  • Slide the unlock tab to the unlock position

  • Slide the release tab in the direction of the arrow, i.e. towards the unlock tab

Voeg opmerking toe

With the tabs still in the unlock position, slide the battery away from the main case.
  • With the tabs still in the unlock position, slide the battery away from the main case.

Voeg opmerking toe

  • Flip the computer over so the Vaio logo is facedown

  • Unscrew the 2 screws next to the battery

Voeg opmerking toe

  • Flip the computer over again so the Vaio logo is face up

  • Open the lid

Voeg opmerking toe

  • Press down on the outer gray shell around the keyboard

  • Use the spudger to gently lift keyboard

  • Do not pull up the keyboard too far as it is attached to a ribbon underneath

There are 2 spring-held latches, one above the F4 and one above the F12. Push a latch up into the frame of the keyboard, then lift the keyboard gently in that area so the latch doesn't spring back. Then push the other latch and the keyboard will be released.

Yishai Sered - Antwoord

  • Lift up lever underneath the ribbon to detach the keyboard.

Voeg opmerking toe

  • Remove memory/wireless compartment cover

Voeg opmerking toe

  • Flip so the Vaio Logo is face down

  • Locate and remove a total of 8 screws on the bottom.

There are 2 more screws on the bottom, one in the middle of the front next to the flash stick socket, and one under the memory door.

Yishai Sered - Antwoord

  • Find and remove 5 screws (they all have arrows next to them) from cover

Voeg opmerking toe

  • Flip the laptop over so the Vaio logo is face up

  • Use the spudger to pop up the upper casing

  • Do not lift too much as the Uppercasing is attached to wires underneath

  • Remove the wires that are attaching the uppercasing to the motherboard

There are also 5 screws from the top of the uppercasing.

Yishai Sered - Antwoord

The are 4 cables to remove: flat cable for the power and S buttons at top center; flat cable for the touchpad at bottom center; and 2 twisted pairs for the speakers.

The speaker cable socket is very delicate. If all you are getting at is the CPU or the hard drive, it may be enough to disconnect the flat cables and gently rotate the uppercasing shifting it left to allow access to the right-hand side with the CPU fan and the hard drive.

Yishai Sered - Antwoord

The top panel has cutouts that allow the cables to be disconnected before the top of the case is removed. The two flat cables are not clamped and can be pulled vertically out of their connectors. The delicate speaker cables are connected to the motherboard with plugs which can be gently levered up out of their sockets.

roberttrevellyan - Antwoord

  • Remove the uppercasing

Voeg opmerking toe

  • Locate the screw holding the optical drive casing to the logic board

  • Remove this screw

This screw is from the bottom, will not be there since you removed it to get the uppercasing.

Yishai Sered - Antwoord

However, there is a screw on the bottom right of the PC-CARD cage to remove.

Yishai Sered - Antwoord

  • Locate ribbon connecting optical drive case to logic board.

  • Pop off the ribbon

  • Remove the metal PC-Card cage

Voeg opmerking toe

  • Locate the four screws holding the optical drive to the logic board

  • Remove the screws

Voeg opmerking toe

  • Locate brown locking tab above optical drive.

  • Lift up on brown locking tab until ribbon is loose

  • Gently slide out and remove the optical drive from the computer

Voeg opmerking toe

  • Remove the blue ribbon from the Ethernet Circuit Board

Voeg opmerking toe

  • Locate the screws near the Ethernet Port circuit board

  • Remove the screws.

Voeg opmerking toe

  • Locate the screws for the second ethernet circuit board

  • Remove the screws

Voeg opmerking toe

  • Remove the ethernet ports

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Één andere persoon heeft deze handleiding voltooid.

Jeffrey Bryan

Lid sinds: 20-04-10

552 Reputatie

11 handleidingen geschreven

Team

Cal Poly, Team 16-4, Maness Spring 2010 Lid van Cal Poly, Team 16-4, Maness Spring 2010

CPSU-MANESS-S10S16G4

4 Leden

11 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 2

Afgelopen 30 Dagen: 8

Altijd: 3,095