Menu

Jouw instellingen

Mijn werkbank

Krijg snel toegang tot handleidingen, onderdelen en antwoorden voor jouw apparaten
Winkelwagen

Het lijkt erop dat je mandje leeg is

Doorblader onze winkel

Sony Ericsson Z500a Logic Board Replacement

Geschreven door: Tim (en 5 andere bijdragers)
  • Reacties: 0
  • Favorieten: 0

Moeilijkheid

Eenvoudig

Stappen

7

Tijd vereist

5 - 10 minuten

Secties

2

Markeringen

1

Step Trimmer

Stappen inkorten

Deze handleiding heeft onnodige stappen. Kort ze in om beknopter te kunnen zijn!

Inleiding

The Logic Board is the part that the keys hit and translates the signals to the phone.

Gereedschap

Koop deze gereedschappen

Onderdelen

Geen onderdelen opgegeven.

  1. Remove the back cover and the battery. Remove the back cover and the battery. Remove the back cover and the battery.

    • Remove the back cover and the battery.

    Bewerken

  2. Remove the 4 screws using a T6 precision screwdriver.

    • Remove the 4 screws using a T6 precision screwdriver.

    • Flip open the phone, and keep the back cover facing you.

    Bewerken

  3. Take the plastic opening tool and run it between the phone case and phone body to loosen the key pad while the phone is open. There are 2 clamps that lock it to the phone case (1 on each side).

    • Take the plastic opening tool and run it between the phone case and phone body to loosen the key pad while the phone is open.

    • There are 2 clamps that lock it to the phone case (1 on each side).

    Bewerken

  4. iPhone Batterij Fix Kits

    Slechts $29.99

    Buy Now

    iPhone Batterij Fix Kits

    Slechts $29.99

    Buy Now

  5. Flip the phone over and lift straight up on the key pad to remove it.

    • Flip the phone over and lift straight up on the key pad to remove it.

    • Be sure to hold the phone flat (parallel to the table), because there are loose parts that may fall out.

    Bewerken

  6. Use the i Pod opening tool to remove the 2 ribbon wires (boxed in the photo) from the logic board.

    • Use the i Pod opening tool to remove the 2 ribbon wires (boxed in the photo) from the logic board.

    Bewerken

  7. Gently lift the back of the logic board and then pull outwards. Be careful not to rip the ribbon wire.

    • Gently lift the back of the logic board and then pull outwards. Be careful not to rip the ribbon wire.

    Bewerken

  8. If the parts are loose you can remove the black sim card reader and green vibrator before continuing, otherwise they may fall out. If the parts are loose you can remove the black sim card reader and green vibrator before continuing, otherwise they may fall out.

    • If the parts are loose you can remove the black sim card reader and green vibrator before continuing, otherwise they may fall out.

    Bewerken
Conclusie

To reassemble your device, follow these instructions in reverse order.

Auteur

met 5 andere bijdragers

Tim

Lid sinds: 20-04-10

9 Reputatie

2 handleidingen geschreven

Badges: 5

+2 andere badges

Team

Cal Poly, Team 7-12, Maness Spring 2010 Lid van Cal Poly, Team 7-12, Maness Spring 2010

CPSU-MANESS-S10S7G12

4 Leden

10 handleidingen geschreven

0 Opmerkingen

Een opmerking toevoegen

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 2

Afgelopen 30 Dagen: 5

Altijd: 1,564