Inleiding

This guide will allow the user to access the motherboard for installation, replacement, or removal.

The battery cover is located on the right side of the camera.
  • The battery cover is located on the right side of the camera.

  • Slide the cover to expose the battery.

Voeg opmerking toe

Ensure that the battery lines up properly with the slot in the camera.
  • Ensure that the battery lines up properly with the slot in the camera.

  • Slide battery in.

  • Slide cover closed.

  • Battery not shown

Voeg opmerking toe

Remove screws from outside of camera. There are 6 screws total. 3 screws on underside. 1 screw on right side, near battery cover.
  • Remove screws from outside of camera. There are 6 screws total.

  • 3 screws on underside.

  • 1 screw on right side, near battery cover.

  • 2 screws on left side.

Voeg opmerking toe

Use screwdriver to remove screws.
  • Use screwdriver to remove screws.

Voeg opmerking toe

Gently pull the front cover off of the main camera.
  • Gently pull the front cover off of the main camera.

  • All of the inner parts of the camera are attached to the back screen.

Voeg opmerking toe

The front cover is now removed from the camera and the internal hardware is now exposed.
  • The front cover is now removed from the camera and the internal hardware is now exposed.

Voeg opmerking toe

This is the camera without the front cover.
  • This is the camera without the front cover.

Voeg opmerking toe

Remove tripod piece located at the bottom of the camera. This piece should slide out with ease.
  • Remove tripod piece located at the bottom of the camera. This piece should slide out with ease.

Voeg opmerking toe

Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are. Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are. Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are.
  • Slide open the top panel. This is located on the top of the camera, where the power button and shutter button are.

Voeg opmerking toe

Pull apart the inner hardware from the back case by prying on the left side. Pull apart the inner hardware from the back case by prying on the left side. Pull apart the inner hardware from the back case by prying on the left side.
  • Pull apart the inner hardware from the back case by prying on the left side.

Voeg opmerking toe

Remove the back cover.
  • Remove the back cover.

Voeg opmerking toe

The back cover is now removed from the internal hardware.
  • The back cover is now removed from the internal hardware.

Voeg opmerking toe

Use the spudger to pry the LCD from the camera.
  • Use the spudger to pry the LCD from the camera.

Voeg opmerking toe

The LCD is now removed from the camera, although attached by a ribbon at the bottom of the camera.
  • The LCD is now removed from the camera, although attached by a ribbon at the bottom of the camera.

Voeg opmerking toe

Flip camera to other side. Use tweezers to peel off black sticker, located in middle of the motherboard.
  • Flip camera to other side.

  • Use tweezers to peel off black sticker, located in middle of the motherboard.

Voeg opmerking toe

Use pry stick to pop out LCD connector ribbon, also called the ZIF connector. Use pry stick to pop out LCD connector ribbon, also called the ZIF connector.
  • Use pry stick to pop out LCD connector ribbon, also called the ZIF connector.

Voeg opmerking toe

The LCD is now removed from the camera.
  • The LCD is now removed from the camera.

Voeg opmerking toe

This is the CCD module.
  • This is the CCD module.

Voeg opmerking toe

Use plastic opening tool pop open the two ribbons attaching to the CCD module.
  • Use plastic opening tool pop open the two ribbons attaching to the CCD module.

  • These are the two ribbons.

Voeg opmerking toe

Remove CCD module.
  • Remove CCD module.

    • You may have to tug on the ribbons to remove the CCD module.

Voeg opmerking toe

The CCD module is now removed from the camera.
  • The CCD module is now removed from the camera.

Voeg opmerking toe

These two screws hold in the AV port. Use Phillips screwdriver to remove screws.
  • These two screws hold in the AV port.

  • Use Phillips screwdriver to remove screws.

Voeg opmerking toe

Remove metal screw plate.
  • Remove metal screw plate.

Voeg opmerking toe

Use pry stick to pop off ribbon.
  • Use pry stick to pop off ribbon.

Voeg opmerking toe

Remove AV port from camera.
  • Remove AV port from camera.

Voeg opmerking toe

The battery cover is located here. Pull away from camera to remove.
  • The battery cover is located here.

  • Pull away from camera to remove.

Voeg opmerking toe

Grip on the top and bottom. Pull up and out to remove motherboard and attached parts.
  • Grip on the top and bottom.

  • Pull up and out to remove motherboard and attached parts.

Voeg opmerking toe

Flip motherboard parts to position shown. There are three ribbons still attached to the motherboard. Pull these three ribbons to remove remaining parts from motherboard.
  • Flip motherboard parts to position shown.

  • There are three ribbons still attached to the motherboard.

  • Pull these three ribbons to remove remaining parts from motherboard.

Voeg opmerking toe

The motherboard is now removed from the camera.
  • The motherboard is now removed from the camera.

Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

3 andere personen hebben deze handleiding voltooid.

Stephannie Allen

Lid sinds: 11-03-13

189 Reputatie

10 handleidingen geschreven

Team

Clemson, Team 13-1, Benson Spring 2013 Lid van Clemson, Team 13-1, Benson Spring 2013

CLEM-BENSON-S13S13G1

4 Leden

10 handleidingen geschreven

Één commentaar

Superb,thank you very much !!!

Vedrasco Victor Vasili - Antwoord

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 1

Altijd: 387