Inleiding

The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function. The vacuum's belt is designed to last approximately 7 years. Replacement of the belt is needed to keep the vacuum at optimal working condition. This replacement guide demonstrates how to replace the belt in the vacuum.

  1. Turn the vacuum on its side.
    • Turn the vacuum on its side.

    • Using a quarter, twist the three green locks to the unlock position.

    • Pull the bottom roller brush cover to open the vacuum.

    Voeg opmerking toe

  2. Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.
    • Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.

    Voeg opmerking toe

    • Remove the three 14.3 mm screws with a T20 screwdriver.

    Voeg opmerking toe

    • Remove the two 14.3 mm screws under the wheels with a T20 screwdriver bit.

    Voeg opmerking toe

    • Remove the two 15.9 mm screws from behind the wheels with a T20 bit screwdriver.

    Voeg opmerking toe

    • Remove the single 13.4 mm small screw behind the roller brush with a PH0 screwdriver bit.

    Voeg opmerking toe

  3. Verspreid de kerstsfeer
    Krijg 12€ korting op je aankoop van 50€ of meer met de code FIXMAS12
    Verspreid de kerstsfeer
    Krijg 12€ korting op je aankoop van 50€ of meer met de code FIXMAS12
    • Remove the single 13.4 mm screw from behind the belted end of the roller brush with a T20 screwdriver bit.

    Voeg opmerking toe

    • Turn the vacuum around.

    • Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights.

    Voeg opmerking toe

    • Remove both of the headlight covers with the spudger.

    Voeg opmerking toe

    • Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel.

    Voeg opmerking toe

    • Remove the two 13.4 mm screws with a T20 bit screwdriver.

    Voeg opmerking toe

    • Remove the single 13.4 mm screw located next to where the belt was detached, securing the motor in place, with a PH1 screwdriver.

    Voeg opmerking toe

    • Remove the visible side of the belt from the gear with a spudger.

    Voeg opmerking toe

    • Remove the grey panel from the opposite side, by uncrewing the single 13.4 mm screw with a PH1 screwdriver. This will release the container for the roller brush and belt motor.

    Voeg opmerking toe

    • Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward.

    Voeg opmerking toe

    • Remove the belt from the gear.

    Voeg opmerking toe

Conclusie

To reassemble your device, follow these instructions in reverse order.

Dakota Rodriguez-Ransom

Lid sinds: 08-10-18

587 Reputatie

2 handleidingen geschreven

Team

Cal Poly, Team S4-G6, White Fall 2018 Lid van Cal Poly, Team S4-G6, White Fall 2018

CPSU-WHITE-F18S4G6

4 Leden

5 handleidingen geschreven

Voeg opmerking toe

Weergavestatistieken:

Afgelopen 24 Uren: 0

Afgelopen 7 Dagen: 0

Afgelopen 30 Dagen: 21

Altijd: 58